Mains PYQs
UPSC IFoS Mains Mech Engg paper 2 2022 questions
- A $4\,\mathrm{m} \times 5\,\mathrm{m} \times 7\,\mathrm{m}$ room is heated by the radiator of steam heating system. The steam radiator transfers heat at a rate of 10,000 kJ/h and a 100 W fan is used to distribute the warm air in the room. The heat losses from the room are estimated to be at the rate of 5,000 kJ/h. If the initial temperature of the room air is $10^\circ$C, determine how long it will take for the air temperature to rise to $20^\circ$C. Assuming constant specific heat of air $[c_p = 1.007\,\mathrm{kJ/kg\,K}]$ and take the value of $R = 0.287\,\mathrm{kPa\,m^3/kg\,K}$ for air.
Further assume room pressure = 100 kPa.
- Using pressure vs crank angle diagrams compare the detonation observed in SI engines with knock of CI engines. Also show that factors which favour knock in SI engines are desirable in CI engines.
- Define the following non-dimensionless numbers and explain their physical significance :
(i) Nusselt number
(ii) Grashof number
(iii) Stanton number
(iv) Prandtl number
- On a cold winter night, with an outside ambient temperature of $5^\circ$C, a wall of the house loses 30 kJ per minute steadily. If the inner and outer surface temperatures of the wall are maintained at $25^\circ$C and $9^\circ$C respectively, what would be the energy destruction rate (in Watts) within the wall ?
- A furnace is shaped like a long equilateral triangular duct where the width of each side is 2 m. Heat is supplied from the base surface, whose emissivity is $\varepsilon_1 = 0.8$, at a rate of $800\,\mathrm{W/m^2}$, while the side surfaces, whose emissivities are 0.5, are maintained at 500 K. Neglecting the end effects, determine the temperature of the base surface. Can you treat this geometry as a two surface encloser ? Take $\sigma = 5.67 \times 10^{-8}\,\mathrm{W/m^2\,K^4}$ and area of base surface = $1\,\mathrm{m^2}$ and total area of other side surfaces = $2\,\mathrm{m^2}$.
- Tank A of volume 500 L contains air at room temperature and 700 kPa pressure. Cylinder B, initially empty, has a piston of mass 100 kg and cross-sectional area $0.5\,\mathrm{m^2}$, and linear spring with spring constant 150 kN/m as shown in the figure. Now the valve is opened and air flows slowly and steadily into cylinder B. The entire system eventually reaches room temperature. Assume air as an ideal gas and atmospheric pressure as 101 kPa. Draw the entire process on P-v diagram for air in cylinder B.
Determine :
(i) Pressure when piston just touches the spring.
(ii) Whether the piston will be at stops in the final state.
(iii) Final pressure of air.
(iv) Work done by air during each process.
[Figure] Tank A connected through a valve to Cylinder B with a piston at the bottom and a spring above; labelled distances 0.3 m (piston to spring) and 0.5 m (piston to stops).
- Consider a water-to-water counter-flow heat exchanger with these specifications. Hot water enters at $95^\circ$C while cold water enters at $20^\circ$C. The exit temperature of hot water is $15^\circ$C greater than that of cold water outlet and mass flow rate of hot water is 50 percent greater than that of cold water. The product of heat transfer surface area and overall heat transfer coefficient is $1400\,\mathrm{W/m^2\,^\circ C}$. Taking the specific heat of both cold and hot water to be $c_p = 4.18\,\mathrm{kJ/kg\,^\circ C}$, determine :
(i) outlet temperature of the cold water,
(ii) effectiveness of the heat exchanger,
(iii) mass flow rate of the cold water, and
(iv) the heat transfer rate.
- Explain the thermal NO formation in SI engines during combustion. List the factors which favour NO formation in-cylinder. Also describe the in-cylinder NO suppression techniques and exhaust treatment techniques followed in modern SI engines.
- Consider a large plane wall of thickness $L = 0.4$ m, thermal conductivity $k = 2.3\,\mathrm{W/m\,^\circ C}$ and surface area $A = 20\,\mathrm{m^2}$. The left side of the wall is maintained at a constant temperature of $80^\circ$C while the right side loses heat by convection to the surrounding air at $T_\infty = 15^\circ$C with a heat transfer coefficient of $h = 24\,\mathrm{W/m^2\,^\circ C}$. Assuming constant thermal conductivity and no heat generation in the wall,
(i) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the wall,
(ii) obtain a relation for the variation of temperature in the wall by solving the differential equation, and
(iii) calculate the rate of heat transfer through the wall.
- Air enters the compressor at the ambient condition of 100 kPa and $25^\circ$C (state 1). At the compressor exit (state 2), the pressure is 10 times of inlet pressure. The compression process is polytropic with $n = 1.40645$. Constant pressure heat addition takes place in a heat exchanger, where the air enters after compression. The temperature at the exit of the heat exchanger is $726.85^\circ$C (state 3). The air then enters the turbine at state 3 and leaves the turbine at 110 kPa (state 4). The expansion process in turbine is polytropic with $n = 1.38727$. Assume air as an ideal gas with mass flow rate of 15 kg/s through all components.
Determine :
(i) the amount of power required for the compression process.
(ii) heat supplied in the heat exchanger (kW).
(iii) power generated by the turbine.
(iv) net power output.
Solve using Air table given.
- Explain the MPFI (Multipoint Port Fuel Injection) system layout which employs mass flow sensor used in multi-cylinder SI engines. Clearly indicate the components present in the layout and their sensing/operational functions.
- A frictionless constant-pressure piston cylinder device, initially contains $0.01\,\mathrm{m^3}$ of Argon gas at 400 K and 350 kPa. Heat is now transferred to Argon from a furnace at 1200 K, and Argon expands isothermally until its volume is doubled. No heat transfer takes place between the Argon and surrounding atmospheric air, which is at $T_0 = 300$ K and $P_0 = 100$ kPa.
Determine :
(i) the useful work output,
(ii) the energy destroyed,
(iii) the reversible work, and
(iv) the maximum available work for this process.
For Argon, take $R = 0.2081\,\mathrm{kJ/kg\,K}$.
- A four-cylinder, four-stroke diesel engine develops 85 kW at 2000 rpm with a specific fuel consumption of 0.235 kg/kWh, and the air/fuel ratio is 25 : 1. The analysis of the fuel shows 87% carbon and 13% hydrogen by mass. The calorific value of fuel used is 4,25,200 kJ/kg. The jacket cooling water flows at 0.25 kg/s and its temperature rise is 48 K. The exhaust gas temperature is $320^\circ$C. Draw up a Heat Balance Chart showing dry exhaust heat and steam heat separately. Take $c_p = 1.85\,\mathrm{kJ/kg\,K}$ for dry exhaust gas and $c_p = 1.9\,\mathrm{kJ/kg\,K}$ for superheated steam. The ambient temperature is $20^\circ$C and the exhaust gas pressure is 1.013 bar.
- Explain the construction and working of a three-way catalytic converter for SI engines. Give details of substrate and wash coat applied for catalysis. Also describe the working of Lambda sensor ($\mathrm{O_2}$-sensor) and explain how it helps in the control of pollutants leaving the tailpipe.
- Explain with a neat sketch, vapour absorption refrigeration system using water and ammonia, with all modifications.
- How can you explain using a Fanno line that a subsonic flow can never become supersonic ?
- Compare velocity compounded impulse turbines with pressure compounded impulse turbines based on the following :
(i) Number of stages
(ii) Position in the steam turbine layout
(iii) Efficiency per stage
(iv) Type of construction of nozzle blade and cost
(v) Possibility of partial admission
(vi) Type of sealing needed for nozzle blades
(vii) Pressure drop per stage
(viii) Total cost of all stages for a given pressure drop
- Explain the selection criteria of refrigerant based on :
(i) Thermodynamic and thermo-physical properties
(ii) Environmental and safety properties
- Discuss briefly the factors that should be considered while selecting the site for a nuclear power plant.
- A freezer of 20 TR capacity has evaporator and condenser temperature of $-30^\circ$C and $25^\circ$C respectively. The refrigerant R-12 is subcooled by $4^\circ$C before it enters the expansion valve and is superheated by $5^\circ$C before leaving the evaporator. The compression is isentropic and the valve throttling and clearance are to be neglected. If a six-cylinder, single-acting compressor with stroke equal to bore running at 1000 rpm is used, determine :
(i) COP of the refrigeration system,
(ii) Mass of refrigerant to be circulated per min, and
(iii) Work input to the compressor in kW.
The specific heat of liquid R-12 is 1.235 kJ/kg K and of vapour R-12 is 0.733 kJ/kg K. The properties of R-12 are given below :
| Saturation Temp | Pressure (bar) | Enthalpy, kJ/kg (Liquid) | Enthalpy, kJ/kg (Vapour) | Entropy, kJ/kg K (Liquid) | Entropy, kJ/kg K (Vapour) | Specific volume, m^3/kg (Liquid) | Specific volume, m^3/kg (Vapour) |
|---|---|---|---|---|---|---|---|
| $-30^\circ$C | 1.0044 | 8.86 | 174.2 | 0.0371 | 0.7171 | 0.000673 | 0.1596 |
| $25^\circ$C | 6.5184 | 59.7 | 197.73 | 0.2239 | 0.6868 | 0.00764 | 0.0269 |
- A Parsons steam turbine with a rotor diameter of 1250 mm rotates at 2500 rpm. If the speed ratio is 0.7 and the blade angle at outlet is $20^\circ$, determine the blade angle at inlet and the diagram efficiency. Draw velocity triangles.
- What is a Deaerator ? Explain its role in a steam power plant. Also draw a sketch to explain its construction and operation.
- A compressor cascade has the following data :
Velocity of air at entry = 75 m/s
Air angle at entry = $48^\circ$
Air angle at exit = $25^\circ$
Pitch - Chord ratio = 1.1
Stagnation pressure loss = 11 m of air column
Density of air = $1.25\,\mathrm{kg/m^3}$
Determine the actual pressure recovery coefficient and the maximum diffuser efficiency.
- Steam at exit of a boiler is at 60 bar and $500^\circ$C. It flows with a velocity of 10 m/s and mass flow rate of 80 kg/s. Determine the number and length of superheater coils of 50 mm internal diameter and 5 mm thickness to be provided. Assume the heat flux in the superheater coils is to be limited to $140\,\mathrm{kW/m^2}$ due to materials restriction.
Use the attached table :
- Air at $30^\circ$C dry bulb temperature and 60% relative humidity is passed through a cooling coil at the rate of $250\,\mathrm{m^3/min}$. The air leaves the coil at $14^\circ$C dry bulb temperature. If the bypass factor of the cooling coil is 0.1, find :
(i) Surface temperature of the cooling coil,
(ii) Relative humidity of the air leaving the cooling coil,
(iii) Capacity of the cooling coil in kW, and
(iv) Sensible heat factor.
Assume barometric pressure = 1.01325 bar
Solve the problem by using Psychrometric chart.
- The maximum demand of a power station is 96 MW and the daily load curve is described below :
| Time (hours) | 0-6 | 6-8 | 8-12 | 12-14 | 14-18 | 18-22 | 22-24 |
|---|---|---|---|---|---|---|---|
| Load (MW) | 48 | 60 | 72 | 60 | 84 | 96 | 48 |
(i) Determine the load factor of the power station.
(ii) What is the load factor of standby equipment rated at 30 MW that takes up all load in excess of 72 MW ?
- Using Buckingham's Pi theorem obtain the expressions for head, capacity and power coefficients of an incompressible flow turbomachine.
- For a centrifugal air compressor running at 7200 rpm, the impeller diameter is 45 cm. The inlet stagnation temperature is 288 K and the pressure coefficient is 0.8. Assuming isentropic flow with no shock, determine the pressure ratio developed. For air, take specific heat at constant pressure as $1.005\,\mathrm{kJ/kg\,K}$ and assume zero swirl at entry.