Mains PYQs
UPSC IFoS Mains Mech Engg paper 2 2021 questions
- Derive the following Clausius-Clapeyron equations :
$$\frac{dP}{dT} = \frac{h_{fg}}{T(V_g - V_f)}$$
and
$$\frac{dP}{P} = \frac{h_{fg}}{RT^2}\,dT$$
Also explain the physical significance of these equations.
- An iron cube at a temperature of $400^\circ\mathrm{C}$ is dropped into an insulated bath containing 10 kg water at $25^\circ\mathrm{C}$. The water finally reaches a temperature of $50^\circ\mathrm{C}$ at steady state. Given that the specific heat of water is 4186 J/kg K. Find the entropy changes for the iron cube and the water. Is the process reversible or irreversible ? (Take $0^\circ\mathrm{C}$ as datum)
- A 12-cylinder, two-stroke cycle CI engine produces 2440 kW of brake power at 550 rpm using stoichiometric light diesel. The engine has bore of 24 cm, stroke of 32 cm, volumetric efficiency of 97%, mechanical efficiency of 88%, combustion efficiency of 98% and air-fuel ratio of $14{\cdot}5$. Calculate the mass flow rate of fuel entering into the engine, brake specific fuel consumption, indicated specific fuel consumption and specific emissions of hydrocarbons due to unburned fuel. [Take density of air $\rho_a = 1{\cdot}181\,\mathrm{kg/m^3}$ and R = gas constant for air $= 0{\cdot}287\,\mathrm{kJ/kg\,K}$]
- What are the various methods for the determination of convection heat transfer coefficient ? Explain briefly.
- A gray, diffuse opaque surface ($\alpha = 0{\cdot}8$) is at $100^\circ\mathrm{C}$ and receives an irradiation of $1000\,\mathrm{W/m^2}$. If the surface area is $0{\cdot}1\,\mathrm{m^2}$, calculate,
(i) Radiosity of the surface.
(ii) Net radiative heat transfer rate from the surface.
(iii) Also calculate the above quantities, if the surface is black. Take $\sigma = 5{\cdot}67 \times 10^{-8}\,\mathrm{W/m^2\,K^4}$
- Oil is being cooled by water in a tube-in-tube parallel flow type heat exchanger. The water enters the inner tube at $15^\circ\mathrm{C}$ and is heated to $50^\circ\mathrm{C}$. The oil flows in the annulus and is cooled from $130^\circ\mathrm{C}$ to $60^\circ\mathrm{C}$. Calculate :
(i) Exit temperature of each of the fluids, if the existing heat exchanger is operated as a counter flow heat exchanger,
(ii) The minimum temperature to which oil may be cooled by increasing the tube length with parallel flow operation, and
(iii) The maximum possible effectiveness in parallel flow operation.
- A thin hollow stainless steel tube with inner diameter $= 7{\cdot}6$ mm and outer diameter $= 8$ mm is heated with a current of 250 A intensity. The outer surface of the tube is insulated and all the heat generated in the tube wall is transferred through its inner surface. The specific resistance and thermal conductivity of steel are $0{\cdot}85\,\mu\Omega\mathrm{m}$ and $18{\cdot}6$ W/mK respectively. Calculate :
(i) Volumetric rate of heat generation in the tube, and
(ii) Temperature drop across the wall.
- Why does a nonquasi-equilibrium expansion process deliver less work than the corresponding quasi-equilibrium one ?
A gas of mass $1{\cdot}5$ kg undergoes a quasi-static expansion which follows a relationship :
$P = a + bV$, where a and b are constants.
The initial and final pressures are 1000 kPa and 200 kPa respectively and the corresponding volumes are $0{\cdot}20\,\mathrm{m^3}$ and $1{\cdot}20\,\mathrm{m^3}$. The specific internal energy of the gas is given by the relation
$U = 1{\cdot}5\,PV - 85$ kJ/kg
where P is in kPa and V is in $\mathrm{m^3/kg}$. Calculate the net heat transfer and the maximum internal energy of the gas attained during expansion.
- Mention four points each of advantages and disadvantages of using hydrogen in SI engines. Explain two methods by which hydrogen can be used in CI engines.
- What are the reasons for the HC emissions in the exhaust of an automobile ? How are catalytic converters helpful in reducing HC, CO and $\mathrm{NO_x}$ emissions ? Why is it good to place a catalytic converter as close to the engine as possible ?
- A long thin glass-walled, $0{\cdot}3$ cm diameter, mercury thermometer is placed in an air stream with convection coefficient of $60\,\mathrm{W/m^2K}$ for measuring transient temperature of air. Consider cylindrical thermometer bulb consists of mercury only, for which $k = 8{\cdot}9$ W/mK and $\alpha = 0{\cdot}016\,\mathrm{m^2/h}$. Calculate the time constant and time required for temperature change to reach half of its initial value.
- An adiabatic turbine receives a gas ($C_P = 1{\cdot}09$ kJ/kg K and $C_V = 0{\cdot}838$ kJ/kg K) at 7 bar and $1000^\circ\mathrm{C}$ and discharges at $1{\cdot}5$ bar and $665^\circ\mathrm{C}$. Determine the Second Law Efficiency and Isentropic Efficiency of the turbine. [Take $T_0 = 298$ K]
- Using Maxwell's relations and the thermodynamic definition for $C_P$ and $C_V$ in terms of gradients, show the following :
(i) $$Tds = C_V\,dT + T\left(\frac{\partial P}{\partial T}\right)_V dV = C_P\,dT - T\left(\frac{\partial V}{\partial T}\right)_P dP$$
(ii) Joule-Thomson coefficient
$$\mu_J = \frac{1}{C_P}\left[T\left(\frac{\partial V}{\partial T}\right)_P - V\right]$$
(iii) Also prove that there is no change in temperature when an ideal gas is made to undergo Joule-Thomson expansion.
- State the three main advantages of induction swirl. The spark plug is fired at $18^\circ$ bTDC in an engine running at 1800 rpm. It takes $8^\circ$ of engine rotation to start combustion and get into flame propagation mode. Flame termination occurs at $12^\circ$ aTDC. Bore diameter is $8{\cdot}4$ cm, and the spark plug is offset by 8 mm from the centreline of the cylinder. The flame front can be approximated as a sphere moving out from the spark plug. Calculate the effective flame front speed during flame propagation.
- Mention the different factors to be considered for selecting the site of hydroelectric power plants.
- Discuss the various pollutants emitting from a steam power plant.
- Distinguish between Turbomachines and Positive Displacement Machines in respect of the following :
(i) Basic mechanism of energy transfer,
(ii) Features of applications, and
(iii) Features of mechanical construction.
- What is an Economiser ? Mention the advantages gained by using Economisers in a modern power plant.
- Explain the psychrometric process of steam injection. Give its applications.
- Distinguish among Fans, Blowers and Compressors.
A compressor draws air from the atmosphere at $1{\cdot}5$ bar and 300 K at a velocity of 80 m/s. The isentropic efficiency of the compressor is 70%. The stagnation pressure ratio is $3{\cdot}2$. Find the stagnation pressure at the exit and the power of the driving motor if the mechanical efficiency is 90% for a flow rate of 30 kg/minute.
Take for air
$\gamma = 1{\cdot}4$
$C_P = 1{\cdot}004$ kJ/kg K
- It is required to design an air-conditioning system for an industrial process for the following conditions :
Outdoor conditions : $32^\circ\mathrm{C}$ DBT and 65% RH
Inside design conditions : $25^\circ\mathrm{C}$ DBT and 60% RH
Volume flow rate of outside air : $195\,\mathrm{m^3/min}$
Coil ADP : $13^\circ\mathrm{C}$
The required condition is achieved by first cooling and dehumidifying the outside air and then by heating.
Calculate the following :
(i) The cooling capacity of the cooling coil and its bypass factor.
(ii) Heating capacity of the heating coil in kW and surface temperature of the heating coil if its bypass factor is $0{\cdot}35$.
(iii) The mass of water vapour removed per hour.
Show all processes on a psychrometric chart along with a schematic diagram to carry out the above processes.
(Psychrometric chart is attached)
- Explain the effect of increase in condenser temperature on the performance of vapour compression system. Draw T-S and P-h diagrams also.
- A single cyclinder, single acting compressor having bore and stroke of 16 cm and 24 cm respectively runs at a speed of 120 rpm and the indicated mean effective pressure is $2{\cdot}2$ bar. The pressure limits of the refrigeration system operating on ammonia are $9{\cdot}74$ bar and $2{\cdot}47$ bar and the temperatures of refrigerant at entry to and exit from condenser are $40^\circ\mathrm{C}$ and $17^\circ\mathrm{C}$ respectively. The cooling water flow across the condenser is $15{\cdot}45$ kg/min and inlet and outlet temperatures of cooling water are $16^\circ\mathrm{C}$ and $24^\circ\mathrm{C}$ respectively. The mass of ice produced per hour from water at $20^\circ\mathrm{C}$ is 56 kg. Assume the latent heat of ice as 335 kJ/kg. Calculate the following :
(i) Compressor power in kW
(ii) Mass flow rate of ammonia/min
(iii) Coefficient of performance
(iv) Dryness fraction of ammonia entering the compressor
The relevant properties of ammonia are given in the table :
| Pressure, P (bar) | Saturation Temperature, $T_S$ ($^\circ$C) | Enthalpy (h), Liquid (kJ/kg) | Enthalpy (h), Vapour (kJ/kg) | Specific heat $C_P$, Liquid (kJ/kg K) | Specific heat $C_P$, Vapour (kJ/kg K) |
|---|---|---|---|---|---|
| 9.74 | 24 | 312.87 | 1482.53 | 4.61 | 2.87 |
| 2.47 | -14 | 135.82 | 1445.2 | - | - |
Take $C_P$ for water as $4{\cdot}1868$ kJ/kg K.
Draw T-S and P-h diagrams also. The state of ammonia is wet vapour at entry to compressor as mentioned in (iv). If the state of ammonia at entry to compressor is either dry saturated or superheated, then comment what will happen to COP and why.
- Explain Load Curves. Distinguish between Base Load and Peak Load power plants.
- For a single stage compressor, the pressure, temperature and velocity of air at the inlet are 120 kPa, 300 K and 12 m/s, respectively. The values of the pressure, temperature and velocity at the exit are 220 kPa, 380 K and 90 m/s, respectively. The exit is 2 m above the inlet. Determine,
(i) Actual work,
(ii) Isentropic work, and
(iii) Efficiency of the compressor.
For air, take
$\gamma = 1{\cdot}4$
$C_P = 1{\cdot}004$ kJ/kg K.
- The following data are related to the design of a single-sided centrifugal compressor :
Power input factor ($\psi$) $= 1{\cdot}02$
Slip factor ($\sigma$) $= 0{\cdot}8$
Rotational speed (N) = 300 rev/s
Overall diameter of impeller $= 0{\cdot}6$ m
Eye-tip diameter $= 0{\cdot}4$ m
Eye-root diameter $= 0{\cdot}2$ m
Air mass flow ($\dot{m}$) = 10 kg/s
Inlet stagnation temperature ($T_{01}$) = 300 K
Inlet stagnation pressure ($P_{01}$) $= 1{\cdot}1$ bar
Isentropic efficiency ($\eta_i$) = 77%
Density of air ($\rho_a$) $= 1{\cdot}185\,\mathrm{kg/m^3}$
Effective efficiency of compression ($\eta_{ec}$) = 88%
$R_{air} = 0{\cdot}287$ kJ/kg K, $C_P$ (air) $= 1{\cdot}005$ kJ/kg K
Take $(\gamma/\gamma - 1)_{air} = 3{\cdot}5$ and $C_{r2} = C_{a1}$.
Determine,
(i) Pressure ratio of the compressor and the power required to drive it, assuming that the velocity of the air at inlet is axial,
(ii) Inlet angle of the impeller vanes at root and tip radii of the eye, assuming that the axial inlet velocity is constant across the eye annulus, and
(iii) Axial depth of the impeller channels at the periphery of the impeller.
- A water turbine of runner diameter $1{\cdot}2$ m works with a head of 112 m of water, $5\,\mathrm{m^3/sec}$ of flow and produces a power of 2700 kW at a speed of 400 rpm. A one-fourth size model of the water turbine is required to be tested in a laboratory. The maximum head available in the laboratory is 8 m of water. Determine,
(i) the flow rate required to be planned,
(ii) the speed at which the model is to be tested, and
(iii) the output of the model.
- Give the mass balance of a steam generator.