Mains PYQs
UPSC IFoS Mains Mech Engg paper 2 2019 questions
- A non-flow quasi-static process occurs for which $P=-3V+16$ bar, where V is the volume in $\mathrm{m^3}$. What is the work done when V changes from $2\,\mathrm{m^3}$ to $6\,\mathrm{m^3}$ ?
- Air flows steadily at the rate of 1 kg/s through an air compressor. The properties of air at entry are velocity 7 m/s, pressure 105 kPa, specific volume $0.95\,\mathrm{m^3/kg}$. The properties at exit are velocity 5 m/s, pressure 700 kPa, specific volume $0.19\,\mathrm{m^3/kg}$. The internal energy of the air increases by 95 kJ/kg, as it flows through the compressor. Cooling water in the compressor jacket removes heat from the air at the rate of 60 kW.
(i) Compute the rate of shaft work input to the air, in kW.
(ii) Find the ratio of inlet pipe diameter to outlet pipe diameter.
- Define specific speed of a turbine. Derive its expression in terms of speed, power and head.
- Explain what you understand by Similitude. Further, explain the following :
(i) Geometric Similarity
(ii) Kinematic Similarity
(iii) Dynamic Similarity
- Sketch and describe a natural circulation high pressure boiler.
- A system at 500 K receives 7000 kJ/min from a source at 1000 K. The temperature of atmosphere is 300 K. Assuming that the temperature of the system and source remain constant during heat transfer, find out :
(i) The entropy produced during heat transfer
(ii) The decrease in available energy of source after heat transfer and increase in available energy of the system.
Show the process on the T-s diagram and mark the increase in unavailable energy.
- Twenty people attend a cocktail party in a small room which measures 9.1 m by 7.6 m and 2.4 m ceiling. Each person generates about 131 W of heat. Assuming that the room is completely sealed off and well insulated, calculate the air temperature rise occurring within 15 minutes if the room temperature is $21^\circ\mathrm{C}$. Volume occupied by each person is $0.07\,\mathrm{m^3}$. The atmospheric pressure is 1.01325 bar. Take $C_v$ of the air as 718 J/kg K.
- Derive an equation describing a Fanno curve. Clearly mention the various assumptions made. Further, prove that at the maximum entropy point Mach number is unity and all processes approach this point.
- A centrifugal compressor compresses air at ambient temperature and pressure of 288 K and 1.01 bar respectively. The impeller tip speed is 364 m/s, the radial velocity at the exit from the impeller is 28 m/s, and the slip factor is 0.891. Calculate the Mach number of the flow at the impeller tip. If the impeller total-to-total efficiency is 0.881 and the flow area from the impeller is $0.085\,\mathrm{m^2}$, calculate the mass flow rate of air. Assume an axial entrance at the impeller eye and radial blades. Take isentropic index of air as 1.4, specific heat at constant pressure as 1005 J/kg K.
- The incremental fuel costs for two generating units a and b of a power plant are given by the following relations :
$$\frac{dF_a}{dP_a}=0.07P_a+55$$
$$\frac{dF_b}{dP_b}=0.08P_b+50$$
where F is the fuel cost in rupees per hour and P is the power output in MW. Calculate,
(i) the economic loading of the two units when the total load supplied by the power plants is 500 MW.
(ii) the loss in fuel cost per hour if the load is equally shared by both the units.
- Air at $15^\circ\mathrm{C}$ and 1.03 bar occupies $0.02\,\mathrm{m^3}$. The air is heated at constant volume until the pressure is 4.2 bar and then cooled at constant pressure to initial temperature $15^\circ\mathrm{C}$. Calculate the net heat flow to or from the air and the net entropy change of air. Treat air as ideal gas. Take $C_p$ of air as 1.005 kJ/kg K and $C_v$ as 0.718 kJ/kg K.
- Determine the value of compressibility factor at critical point for gases following Van der Waal's equation of state.
- The power P developed by a water turbine depends on the rotational speed N, operating head H, gravity g, diameter D and breadth B of the runner, density $\rho$ and viscosity $\mu$ of water. Show by using Buckingham's $\pi$-theorem method,
$$P=\rho D^5N^3\phi\left[\frac{H}{D},\frac{D}{B},\frac{\rho D^2N}{\mu},\frac{ND}{\sqrt{gH}}\right].$$
- The following particulars refer to an experimental determination of the calorific value of a sample of fuel containing 88% C and 4.2% $\mathrm{H_2}$. Mass of fuel is 0.848 gm. Mass of fuse wire 0.027 gm, of calorific value 6700 J/gm. Mass of water in the calorimeter is 1950 gm. Water equivalent of calorimeter is 380 gm. It is observed that rise in temperature is $3.06^\circ\mathrm{C}$. The cooling correction is $0.017^\circ\mathrm{C}$.
Find the higher calorific value of the fuel. Take $C_p$ of water as 4.18 kJ/kg K.
- Define (i) fin effectiveness $\varepsilon_f$, and (ii) fin efficiency $\eta_f$. Obtain expressions for $\varepsilon_f$ and $\eta_f$ for an infinitely long fin of uniform cross-section. Also, from the expression derived for $\varepsilon_f$, enumerate the conditions under which use of fins can be justified.
- Liquid nitrogen is stored in a thin walled spherical container of 100 cm diameter. The system is insulated by an evacuated space between the inner sphere and the surroundings with 105 cm concentric sphere. Both the spheres are made of aluminium and have an emittance of 0.03. The inner surface of the sphere is maintained at 77.4 K and the temperature of the outer sphere is 280 K. The latent heat of vaporization of nitrogen is 200 kJ/kg.
Estimate
(i) the rate of heat flow by radiation to the nitrogen in the container, and
(ii) the nitrogen boil-off rate.
- A room is to be kept at a temperature of $20^\circ\mathrm{C}$ and a pressure of 1.013 bar. The moist air at $430\,\mathrm{m^3/hr}$ is drawn from a supply at $5^\circ\mathrm{C}$, 1.013 bar and 70% relative humidity, and is saturated with water vapour in a sprayer. Determine the amount of water added per hour at $5^\circ\mathrm{C}$.
Partial pressure of water vapour at $5^\circ\mathrm{C}$ = 0.0061 bar.
For air, R = 287 J/kJ K.
- Mention which factors affect the octane requirement of an engine.
- Draw the schematic representation of disintegration of fuel jet in CI engine without swirl and with swirl.
- A vapour compression refrigeration system of 2400 kJ/min capacity works at an evaporator temperature of $-10^\circ\mathrm{C}$ and a condenser temperature of $50^\circ\mathrm{C}$. The refrigerant R134a is subcooled by $5^\circ\mathrm{C}$ before entering the expansion valve and the vapour is superheated by $5^\circ\mathrm{C}$ before leaving the evaporator. The compression of the refrigerant is reversible adiabatic. The refrigeration compressor is having two cylinders, single acting with stroke equal to 1.5 times the bore and runs at 1000 rpm. Determine : (i) Refrigeration effect per kg of refrigerant, (ii) Mass of refrigerant circulated per minute, (iii) Theoretical piston displacement per minute, (iv) Power required to run the compressor, and (v) Bore by stroke of the compressor cylinder. Thermodynamic properties of R134a are attached.
- A simple jet carburettor is required to supply 6 kg of air per minute and 0.45 kg of fuel of density $740\,\mathrm{kg/m^3}$. The air is initially at 1.01325 bar and $27^\circ\mathrm{C}$. Calculate the throat diameter of the choke for a flow velocity of 92 m/s. Velocity coefficient is 0.81.
If the pressure drop across the fuel metering orifice is 0.75 of that of the choke, calculate orifice diameter assuming coefficient of discharge is 0.6. Take for air specific heat at constant pressure as 1000 J/kg K and isentropic index as 1.4.
- Show that by Reynolds analogy for turbulent flow through a tube $St_d=\frac{f}{8}$ where f is the friction factor.
- Two square gray surfaces are oriented as shown in the figure. Surface $A_1$ is to be maintained at $400^\circ\mathrm{C}$ and surface $A_2$ at $800^\circ\mathrm{C}$ in a large surrounding whose walls are at $30^\circ\mathrm{C}$. The surface properties are $\varepsilon_1=0.5$ and $\varepsilon_2=0.3$. Determine the energy supply requirements to maintain the surfaces at the given temperatures. Assume $F_{12}=F_{21}=0.28$. Draw the equivalent network for radiation.
[Figure] Two square surfaces $A_1$ (at $T_1$) and $A_2$ (at $T_2$) joined along an edge at right angles, with surroundings at $T_3$; each side marked 0.5.
- Oil is used to heat water in a 1 - 2 heat exchanger (1 shell pass and 2 tube passes). Oil enters the tube at $240^\circ\mathrm{C}$ with a mass flow rate of 7 kg/sec. The heat exchanger is to be designed so that the water leaves the heat exchanger with a minimum temperature of $80^\circ\mathrm{C}$. The flow rate of water is 10 kg/sec and it enters the heat exchanger at $20^\circ\mathrm{C}$. Assuming an overall heat transfer coefficient of $525\,\mathrm{W/m^2K}$, determine heat transfer surface area required to achieve the outlet temperature of $80^\circ\mathrm{C}$. Assume $C_p$ of oil = 2.1 kJ/kg K.
[Figure] Chart of correction factor F against $P=(T_{t,out}-T_{t,in})/(T_{s,in}-T_{t,in})$ for a heat exchanger with one shell pass and two (or a multiple of two) tube passes, with curves for Z from 0.1 to 20.0, and a sketch of the exchanger with $T_{s,in}$, $T_{s,out}$, $T_{t,in}$, $T_{t,out}$.
- The following observations were made during a test on an oil engine : Brake power is 30 kW, fuel consumed is 10 kg/hr with calorific value of 42,000 kJ/kg. The mass flow rate of water circulated in water jacket is 9 kg/min. The rise in cooling water temperature is $60^\circ\mathrm{C}$.
The exhaust gases are passed through an exhaust gas calorimeter for determining the heat carried away by exhaust gases. The calorimeter detail are as follows : water circulated through the calorimeter is 9.5 kg/min and the rise in temperature is $40^\circ\mathrm{C}$. The exhaust gases leave the calorimeter at $80^\circ\mathrm{C}$. Air/fuel ratio on mass basis is 20 and the ambient temperature is $17^\circ\mathrm{C}$. Mean specific heat of exhaust gases is 1 kJ/kg K and specific heat of water is 4.18 kJ/kg K. Draw the heat balance on kJ/min and percentage basis.
- A spark ignition engine fuel has a composition of 86% carbon and 14% hydrogen by weight. The engine is supplied with a fuel having equivalence ratio of 1.20. Assume that all hydrogen is burnt and that the carbon burns to carbon monoxide and carbon dioxide so that there is no free carbon left. Calculate the percentage analysis of dry exhaust gases by volume.
- A bootstrap air refrigeration system is used for an aeroplane to take 10 TR load when it is flying at an altitude of 2000 m. The ambient air conditions are 0.8 bar and $15^\circ\mathrm{C}$. The air is rammed isentropically from 0.8 bar to 1.05 bar. The pressure of air after isentropic compression in the main compressor is 3.5 bar and this is further compressed in a secondary compressor to a pressure of 4.5 bar. The isentropic efficiencies of both the compressors are 90% and that of cooling turbine is 85%. The effectiveness of both the heat exchangers is 0.6. If the cabin is to be maintained at $20^\circ\mathrm{C}$ and the pressure in the cabin is 0.9 bar, find
(i) Mass of air passing through the cabin
(ii) Power used for the refrigeration system
(iii) COP of the system
Draw a neat sketch of the system and show the processes on T-s diagram. Take $C_p=1$ kJ/kg K.
- A horizontal cylinder of 50 cm length and 3 cm diameter is suspended in water at $20^\circ\mathrm{C}$. Calculate the rate of heat transfer if the surface temperature of the cylinder is maintained at $55^\circ\mathrm{C}$. Also, determine the rate of heat transfer if the same cylinder is kept horizontally in a bath of light oil at $55^\circ\mathrm{C}$.
Use the following properties :
| Property | Water | Oil |
|---|---|---|
| $\rho$ (kg/m$^3$) | 992 | 905 |
| $\mu$ (kg/m hr) | 2.47 | 82.0 |
| k (W/mK) | 0.622 | 0.133 |
| $\beta$ (K$^{-1}$) | $3.96\times10^{-4}$ | $7.2\times10^{-4}$ |
| Pr | 4.64 | 324 |
Use the following table :
| $Ra_D$ | C | n |
|---|---|---|
| $10^{-10}-10^{-2}$ | 0.675 | 0.058 |
| $10^{-2}-10^{2}$ | 1.02 | 0.148 |
| $10^{2}-10^{4}$ | 0.85 | 0.188 |
| $10^{4}-10^{7}$ | 0.48 | 0.25 |
| $10^{7}-10^{12}$ | 0.125 | 0.333 |