Mains PYQs
UPSC Mains Mechanical Engineering paper 1 2026 questions
- A uniform beam has a mass of 50 kg per metre length. Compute the reactions at the support O. The force loads shown lie in a vertical plane.
[Figure] Beam fixed at O; horizontal run O to A of 1.8 m, then 0.6 m to the bend, inclined at 30 degrees with segments B and C of 0.6 m each; loads: 3 kN downward at A, 4 kN-m moment at B, 1.4 kN at C.
- [Figure] Fixed-ended bar ABCD, end segments of area $A_1$ and length $L_1$, middle segment BC of area $A_2$ and length $L_2$, loads $P_B$ at B and $P_C$ at C.
The fixed-ended bar ABCD consists of three prismatic segments, as shown in the figure. The end segments have a cross-sectional area $A_1 = 840\,\mathrm{mm^2}$ and length $L_1 = 200\,\mathrm{mm}$. The middle segment has a cross-sectional area $A_2 = 1260\,\mathrm{mm^2}$ and length $L_2 = 250\,\mathrm{mm}$. Loads $P_B$ and $P_C$ are equal to $25.5\,\mathrm{kN}$ and $17.0\,\mathrm{kN}$, respectively.
(i) Determine the reactions $R_A$ and $R_D$ at the fixed supports.
(ii) Determine the compressive axial force $F_{BC}$ in the middle segment of the bar.
- Why is grain size important in polycrystalline materials ? How is it estimated ?
(i) Determine the ASTM grain size number of a metal specimen if 75 grains/square inch are measured at a magnification of $100\times$.
(ii) For the same specimen, how many grains/$\mathrm{inch^2}$ can be estimated at a magnification of $60\times$ ?
- In a gear drive, the power component is 0.94 times the normal thrust with the addendum for stub teeth being 85% of the module. Determine the minimum number of teeth to avoid undercutting and length of path of contact in terms of module, m, if :
(i) The gear ratio is unity.
(ii) The gear ratio is 2.5.
- A turbine shaft of diameter d is under a thrust load P and torque T (as shown in the figure). Calculate the largest permissible value of the load P if the allowable normal stress is not to exceed $\sigma_{all}$.
[Figure] Shaft of diameter d with thrust P and torque T at the ends.
Given : $d = 60\,\mathrm{mm}$, $T = 2\,\mathrm{kN.m}$, $\sigma_{all} = 220\,\mathrm{MPa}$
- What is heat treatment ? What is its purpose ? Explain different heat treatment processes with the help of common microstructural phases of steel on an Iron-Carbon equilibrium diagram.
- A steel tube has a mean diameter of 100 mm and a thickness of 3 mm. Calculate the torque which can be transmitted by the tube with a factor of safety of 2.25, if the criterion of failure is :
(i) Maximum shear stress
(ii) Maximum strain energy
(iii) Maximum shear strain energy
The elastic limit of the steel in tension is $225\,\mathrm{MN/m^2}$ and Poisson's ratio $\nu$ is 0.3.
- The effective turning moment of a two-wheeler engine crankshaft for every $180^\circ$ of crank rotation is represented by :
$T\,(\mathrm{N\text{-}m}) = 8000 + 1000\sin 2\theta - 2000\cos 2\theta$
where $\theta$ is the crank inclination with respect to the inner dead centre. A flywheel of 500 kg mass with radius of gyration of 750 mm is provided on the crank. Assuming external resistance as constant at an engine speed of 300 rpm, determine :
(i) The maximum, minimum and mean torques. Also represent them on a $T - \theta$ diagram.
(ii) The power developed.
(iii) Total percentage fluctuation in speed.
(iv) If, owing to size constraints, radius of gyration of the flywheel is reduced to 600 mm, will the percentage (%) fluctuation of speed increase ? If yes, then by how much ?
- (i) The acceleration of a particle along a straight line is defined by $a = (2t - 9)\,\mathrm{m/s^2}$, where t is in seconds. At $t = 0$, $s = 1\,\mathrm{m}$ and $v = 10\,\mathrm{m/s}$. When $t = 9\,\mathrm{s}$, determine :
(I) The particle's position,
(II) The total distance travelled, and
(III) The velocity of the particle. [10]
(ii) A pressurized steel tank is constructed with a helical weld that makes an angle $\alpha = 55^\circ$ with the longitudinal axis (as shown in the figure). The tank has radius $r = 0.6\,\mathrm{m}$, wall thickness $t = 18\,\mathrm{mm}$, and internal pressure $P = 2.8\,\mathrm{MPa}$. Also, the steel has modulus of elasticity $E = 200\,\mathrm{GPa}$ and Poisson's ratio $\nu = 0.30$.
[Figure] Cylindrical tank with a helical weld at angle $\alpha$ to the longitudinal axis.
Determine the following quantities for the cylindrical part of the tank :
(I) The circumferential and longitudinal stresses.
(II) The maximum in-plane and out-of-plane shear stresses.
(III) The circumferential and longitudinal strains. [10]
- (i) The surface of an airplane wing is subjected to plane stress with normal stresses $\sigma_x$ and $\sigma_y$ and shear stress $\tau_{xy}$, as shown in the figure. At a counterclockwise angle $\theta = 32^\circ$ from the x-axis, the normal stress is 37 MPa tension, and at an angle $\theta = 48^\circ$, it is 12 MPa compression. If the stress $\sigma_x$ equals 110 MPa tension, what are the stresses $\sigma_y$ and $\tau_{xy}$ ?
[Figure] Stress element with $\sigma_x = 110\,\mathrm{MPa}$, $\sigma_y$ and $\tau_{xy}$. [10]
(ii) Determine the damped natural frequency of the system shown in the figure.
[Figure] Lever pivoted at O with spring k at A (distance a), damper C connected at distance b, mass m at distance l from O. [10]
- A glass-epoxy composite consists of full length fibers of E-glass with modulus 72.5 GPa embedded in epoxy matrix with modulus 3.5 GPa. The volume percentage of glass fibers is 35%.
Compute :
(i) The modulus of elasticity of the composite in longitudinal and transverse directions.
(ii) The strain sustained by fibers and matrix, if a stress of 50 MPa is imposed on a cross-sectional area of $250\,\mathrm{mm^2}$.
- A simple beam is loaded as shown in the figure. Using the double-integration method, determine the following :
[Figure] Simply supported beam AB of length L, support A (pin) and B (roller), triangular distributed load decreasing from $W_0$ at A to zero at B.
(i) The equation of the elastic curve
(ii) The slope at the end A
(iii) The deflection at the midspan
- A shaft carries three eccentric masses of 1 kg each at radial distances of 20, 30 and 20 mm with the central plane 50 mm apart. Their angular positions are $120^\circ$ apart. If the shaft is balanced by adding two masses at a radius of 700 mm and at distances of 100 mm each from the central plane of the middle eccentric,
(i) Determine the magnitudes and angular positions of the masses.
(ii) If one of the masses is shifted to a radius of 50 mm due to space constraints, determine the change in its magnitude. Will there be any change in the mass and location of the other masses ?
- Determine the magnitude P of the horizontal force required to initiate motion of the block of mass $m_0$ for the cases :
(A) P is applied to the right, and
(B) P is applied to the left.
Compute a general solution in each case, and then evaluate your expression for the values $\theta = 30^\circ$, $m = m_0 = 3\,\mathrm{kg}$, $\mu_s = 0.60$, and $\mu_k = 0.50$.
[Figure] Block $m_0$ on a horizontal floor against a wall, with a bar of mass m from A on the block to a hinge at B on the wall at angle $\theta$; force P(A) acts to the left of the block and P(B) to the right; friction coefficients $\mu_k$ and $\mu_s$ marked.
- A cylindrical workpiece of 60 mm diameter is turned down to 50 mm over a length of 120 mm on a CNC lathe with cutting speed of 120 m/min and feed of 0.3 mm/rev. Find the machining time.
- A firm chooses between two processes (X and Y) to manufacture a component. Process X has a fixed cost of ₹9,60,000/year with a variable cost of ₹55/unit. Process Y has a fixed cost of ₹15,00,000/year with a variable cost of ₹38/unit. The selling price is ₹110/unit.
(i) Calculate the break-even volume for each process independently.
(ii) Determine the cross-over point between Process X and Process Y.
(iii) If the firm forecasts demand of 35,000 units, compute the profit under each process and recommend a choice. What is the margin of safety (%) under the preferred process.
- A laser beam delivers 5 J of energy in 0.01 sec over an area of $0.5\,\mathrm{mm^2}$. Calculate the power density of the laser beam.
- A production process is monitored using $\bar{X}$ and R charts. Fifteen subgroups of size n = 5 were inspected. The grand mean $\bar{\bar{X}} = 48.6\,\mathrm{mm}$ and the mean range $\bar{R} = 4.2\,\mathrm{mm}$. Use the following control chart constants :
$A_2 = 0.577$, $D_3 = 0$, $D_4 = 2.114$, where
$A_2$ is for the $\bar{X}$ chart, $D_3$ and $D_4$ are for the R chart
(i) Compute the upper and lower control limits for both the $\bar{X}$ chart and the R chart.
(ii) A separate attribute inspection of 20 lots of 200 units each found a total of 184 defective units. Construct a p-chart : compute $\bar{p}$, upper control limit (UCL-p) and lower control limit (LCL-p).
- Discuss the factors affecting surface finish in machining operations, and list the different profile finishing techniques used in modern manufacturing.
- A strip of width 250 mm is reduced from 30 mm to 20 mm thickness in a rolling mill of roll radius 400 mm. Considering coefficient of friction 0.25 and average flow stress 300 MPa, find the following :
(i) Contact length
(ii) Rolling force
(iii) Check if the biting condition is satisfied
- A biomedical implant requires excellent surface integrity with no thermal damage. From the perspective of non-conventional machining, discuss the following :
(i) Suitability of USM, LBM, EDM for biomedical implant machining
(ii) Surface defects in each process
(iii) Best process selection with justification
(iv) Post-processing requirements of the selected process
- A job shop has four machines ($M_1 - M_4$) and five jobs ($J_1 - J_5$), all available at t = 0. Each job has a unique routing. The processing time (hours) and due dates are given below.
| Job | Routing | Total Work | Due Date |
|---|---|---|---|
| $J_1$ | $M_1 \to 6$, $M_2 \to 4$, $M_3 \to 8$, $M_4 \to 3$ | 21 | 28 |
| $J_2$ | $M_2 \to 5$, $M_1 \to 7$, $M_4 \to 2$, $M_3 \to 6$ | 20 | 25 |
| $J_3$ | $M_3 \to 4$, $M_2 \to 8$, $M_1 \to 3$, $M_4 \to 5$ | 20 | 30 |
| $J_4$ | $M_1 \to 9$, $M_3 \to 3$, $M_2 \to 5$, $M_4 \to 4$ | 21 | 35 |
| $J_5$ | $M_2 \to 6$, $M_3 \to 5$, $M_4 \to 7$, $M_1 \to 2$ | 20 | 32 |
(i) Define the critical ratio (CR). Compute the CR for each job at t = 0 and rank them by urgency (lowest CR = highest priority). State which job is the most critical and explain in two sentences why the CR is more informative than the due date or processing time alone.
(ii) Apply the shortest processing time (SPT) dispatching rule - at each machine, when free, select the waiting job with the smallest operation time for that machine. Construct a complete Gantt chart. Compute for each job : Completion time $C_j$, Flow time $F_j$, Lateness $L_j$, and Tardiness $T_j$. Summarise : makespan, mean flow time, total tardiness, maximum tardiness, number of tardy jobs.
- (i) In an orthogonal cutting operation, the following data are obtained :
Cutting force $F_c = 1500\,\mathrm{N}$
Thrust force $F_t = 900\,\mathrm{N}$
Rake angle $\alpha = 10^\circ$
Chip thickness ratio $r = 0.4$
Determine the following :
(I) Shear angle ($\phi$)
(II) Friction angle ($\beta$)
(III) Coefficient of friction ($\mu$)
(IV) Shear force ($F_s$) using Merchant's circle relations [15]
(ii) A hole is specified as $25 \pm 0.01\,\mathrm{mm}$. Using Taylor's principle, determine the following :
(I) GO gauge size
(II) NO-GO gauge size
Assume :
(A) Gauge tolerance = 10% of work tolerance
(B) Wear allowance = 10% (only GO gauge) [5]
- In an organization, what do you understand by the roles of flexibility, lean practices and agility ? Explain how flexibility, lean practices and agility are complementary approaches.
- A manufacturing firm is redesigning its assembly line and is debating whether to use traditional time study (stopwatch) or predetermined time standards (PTS). Answer the following :
(i) Explain the conceptual basis of PTS. What fundamental assumption makes it possible to preassign time values to basic motions independently of the task context ?
(ii) Describe two specific situations in which PTS would be preferred over time study for capacity planning purposes, and two situations where it would be inappropriate.
- A shaft of nominal size 60 mm is to be fitted into a hole. The tolerances are :
Hole tolerance - 0.030 mm
Shaft tolerance - 0.020 mm
Minimum clearance required - 0.010 mm
Determine the following :
(i) Maximum clearance
(ii) Hole and shaft limits
(iii) Allowance
- A manufacturing firm producing both standardized and customized products is planning a new facility.
(i) Critically compare product layout and process layout in terms of material flow, flexibility, cost, demand variability and machine utilization.
(ii) Explain the concept of cellular layout and analyze the challenges in its implementation along with its advantages.
- A spare parts store faces stochastic demand. Annual demand is normally distributed with mean ($\mu$) = 2400 units and standard deviation $\sigma_D$ = 300 units. Lead time is fixed at 2 weeks.
Assume 50 working weeks/year. Ordering cost = ₹800/order, Holding cost = ₹18/unit/year, Unit cost = ₹240, and Stockout cost = ₹90/unit short. The store operates with a continuous review policy.
(i) Compute the Economic Order Quantity.
(ii) Determine the demand during lead time (mean and standard deviation).
(iii) If the desired service level is 95% (z = 1.645), calculate the safety stock and reorder point.
(iv) Compute the total annual inventory cost (ordering + holding + safety stock holding). By how much does safety stock inflate total holding cost compared to the zero safety stock scenario ?