Mains PYQs
UPSC Mains Mechanical Engineering paper 2 2025 questions
- A lump of ice with a mass of 1.5 kg at an initial temperature of 260 K melts at the pressure of 1 bar as a result of heat transfer from the environment. After some time, the resulting water attains the temperature of environment, 293 K. Calculate the entropy production associated with this process. The latent heat of fusion of ice is 334 kJ/kg, the specific heat of ice and water are 2.07 kJ/kg-K and 4.2 kJ/kg-K, respectively. Assume that ice melts at 273.15 K.
- Downstream of a normal shock wave, the characteristic Mach number $M_y^* = 0.5$ and the stagnation pressure is 2 bar. Determine the following:
(i) The Mach number $M_y$ downstream of the shock
(ii) The stagnation pressure upstream of the shock
The fluid is air and $\gamma = 1.4$, and $R = 0.287$ kJ/kg-K.
Normal shock table and Isentropic flow table provided at the end, may be used.
- Show, in the form of a table, how the following parameters change (increase/decrease/remain constant) across a normal shock wave:
Static pressure, Static temperature, Stagnation pressure, Stagnation temperature, Stagnation density, Mach number, Entropy and Stagnation enthalpy
- At a certain instant of time, the temperature across a large wall of thickness 50 cm is given as
$$T(x) = 90 - 80x + 16x^2 + 32x^3 - 25x^4$$
where $x$ is in metres and measured from the left face of the wall as shown in the figure below and $T$ is in $^\circ$C. If the area of the wall is $10\,\mathrm{m^2}$ and there is no generation of heat in the wall, compute the following:
(i) The rate of heat entering and leaving the wall
(ii) The rate of heat energy stored in the wall
(iii) The rate of temperature change with time at $x = 0$ and $x = 0.5$ m
[Figure] Wall of thickness 50 cm with x-axis marked at x = 0 and x = 0.5 m
- A 120 W electric bulb has a filament temperature of 3005 $^\circ$C. Assuming the filament to be black, calculate (i) the diameter of the filament wire if the length is 250 mm and (ii) the efficiency of the bulb based on visible radiation if the visible radiation lies in the wavelength range from 0.4 $\mu$m to 0.75 $\mu$m. Assume Stefan-Boltzmann constant ($\sigma$) as $5.67\times10^{-8}\,\mathrm{W/m^2\text{-}K^4}$. The black body radiation functions are given in the table:
| $\lambda T$ ($\mu$m-K) | $f_{0\to\lambda}$ |
|---|---|
| 1300 | 0.004317 |
| 1400 | 0.007791 |
| 2400 | 0.140266 |
| 2500 | 0.161366 |
- (i) A reversible power cycle engine is used to drive a reversible heat pump. The power cycle takes in $Q_1$ heat units at temperature $T_1$ and rejects heat $Q_2$ at temperature $T_2$. The heat pump abstracts heat $Q_4$ from the sink at temperature $T_4$ and discharges heat $Q_3$ at temperature $T_3$. Develop an expression for the ratio $Q_4/Q_1$ in terms of the four temperatures $T_1$, $T_2$, $T_3$ and $T_4$. [10]
(ii) Argon gas expands adiabatically in a turbine from 2 MPa, 1000 $^\circ$C to 350 kPa. The mass flow rate of argon is 0.5 kg/s and the turbine develops power at the rate of 120 kW. Determine the following:
(1) The temperature of argon at the turbine exit
(2) The irreversibility rate
(3) The second law efficiency
Neglect kinetic and potential energy effects and take $T_0 = 20$ $^\circ$C and $P_0 = 1$ atm. Take molecular weight of argon as 40 kg/kmol and $\gamma = 1.67$. ($T_0$ and $P_0$ are the environment temperature and pressure, respectively) [10]
- Compressed air is transported in an industrial pipeline of 50 mm internal diameter. The stagnation conditions at the inlet are $P_0 = 10$ bar and $T_0 = 400$ K. The average Fanning friction factor $\bar{f} = 0.002$. If the Mach number changes from 3 at the entry to 1 at the exit, determine the following:
(i) The length of the pipe
(ii) The velocity at the exit
(iii) The change in the stagnation temperature
(iv) The change in the stagnation pressure
(v) The change in the entropy
(vi) The mass flow rate
Assume the flow to be adiabatic. For air, take $\gamma = 1.4$ and $R = 287$ J/kg-K.
Isentropic flow table and Fanno flow table attached at the end, may be used.
- A thin flat plate, that is 0.2 m $\times$ 0.2 m on a side, is oriented parallel to an atmospheric air stream having a velocity of 40 m/s. The air is at a temperature of $T_\infty = 20$ $^\circ$C, while the plate is maintained at $T_s = 120$ $^\circ$C. The air flows over the top and bottom surfaces of the plate, and measurement of the drag force reveals a value of 0.075 N. What is the rate of heat transfer from both sides of the plate to the air?
(Assume $\rho_{air} = 0.995\,\mathrm{kg/m^3}$, $\nu_{air} = 20.92\times10^{-6}\,\mathrm{m^2/s}$, $\mathrm{Pr}_{air} = 0.7$, $k_{air} = 30\times10^{-3}$ W/m-K)
- A long cylindrical rod of radius 10 cm consists of a nuclear reacting material ($k = 0.5$ W/m-K) generating $24000\,\mathrm{W/m^3}$ uniformly throughout its volume. The rod is encapsulated within another cylinder whose outer radius is 20 cm and that has a thermal conductivity of 4 W/m-K. The outer surface is surrounded by a fluid at 100 $^\circ$C, and the convection coefficient between the surface and the fluid is 20 $\mathrm{W/m^2}$-K. Find the temperatures of the interface between the two cylinders, at the outer surface and the maximum temperature under steady-state condition.
- A centrifugal compressor is to be designed for an industrial application handling air. The inlet stagnation conditions are $P_{0_1} = 1.1$ bar and $T_{0_1} = 295$ K. The air enters the eye of the impeller axially, without any prewhirl. The axial velocity is uniform throughout the eye and is equal to 143 m/s. The eye tip and root diameters are 0.30 m and 0.15 m, respectively. Calculate the mass flow rate of air.
The overall diameter of the impeller is 0.50 m. The power input factor is 1.04 and the slip factor is 0.9. The rotational speed of the compressor is 290 revolutions/second. The isentropic efficiency of the compressor (based on total head) is 0.78. The radial velocity at the impeller tip is 143 m/s. Assume that 'half the total losses' occurs in the impeller. Determine the pressure ratio and the power required to drive the compressor. Also, determine the axial depth of the impeller channels at the periphery of the impeller. Draw the $T$-$s$ diagram showing the variations of both static and stagnation pressures and temperatures in the impeller and the diffuser.
For air, $\gamma = 1.4$, $C_p = 1.005$ kJ/kg-K.
- The velocity and temperature profiles for laminar flow in a tube of radius $r_0 = 10$ mm have the form at a particular axial location
$$u(r) = 0.1\left(1 - \frac{r^2}{r_0^2}\right)$$
$$T(r) = 344.8 + 75\frac{r^2}{r_0^2} - 18.8\frac{r^4}{r_0^4}$$
with units of m/s and K, respectively. Determine the corresponding value of the mean (or bulk) temperature $T_m$ at this axial position.
- A shell and tube type condenser is employed in a steam power plant to handle 35000 kg/h of dry and saturated steam at 50 $^\circ$C. The cooling water enters the condenser at 15 $^\circ$C and leaves at 25 $^\circ$C. The tubes are of 22.5 mm inside diameter and 25 mm outside diameter. The water flows through the tubes at an average velocity of 2 m/s. The heat transfer coefficient on steam side is 5001 $\mathrm{W/m^2}$-K.
Calculate the following:
(i) The mass flow rate of water (in kg/s)
(ii) The heat transfer surface area (based on $U_0$)
(iii) The number of tubes required for water flow
(iv) The number of tube passes in condenser if the length of each tube pass should not be more than 2.5 m
Assume that condensate coming out from the condenser is saturated water and resistance of tube wall is negligible. For waterside heat transfer coefficient, use the correlation Nu = $0.023\,\mathrm{Re}^{0.8}\,\mathrm{Pr}^{0.4}$. Take latent heat of steam as 2374 kJ/kg. The properties of water at mean bulk temperature of 20 $^\circ$C are as follows:
Pr = 6.98
$\rho = 998.9\,\mathrm{kg/m^3}$
$C_p = 4.180$ kJ/kg-K
$\nu = 1.0006\times10^{-6}\,\mathrm{m^2/s}$
$k_f = 0.59859$ W/m-K
Assume fully developed flow through tubes and a single shell is used.
- A stationary gas turbine plant operates on a Brayton cycle and delivers 20 MW to an electric generator. The maximum temperature is 1200 K and the minimum temperature is 290 K. The minimum pressure is 95 kPa and the maximum pressure is 380 kPa. If the isentropic efficiencies of the turbine and compressor are 0.85 and 0.8, respectively, find-
(i) the mass flow rate of air to the compressor;
(ii) the volume flow rate of air to the compressor;
(iii) the fraction of turbine work output needed to drive the compressor;
(iv) the cycle efficiency.
If a regenerator of 75% effectiveness is added to the plant, what would be the changes in the cycle efficiency and net work output?
Assume $C_p$ and $C_v$ for air as 1.005 kJ/kg-K and 0.718 kJ/kg-K, respectively.
- The heat transfer rate due to free convection from a vertical surface, 1 m high and 0.6 m wide, to quiescent air that is 20 K colder than the surface is known. What is the ratio of the heat transfer rate for that situation to the rate corresponding to a vertical surface, 0.6 m high and 1 m wide, when the quiescent air is 20 K warmer than the surface? Neglect heat transfer by radiation and any influence of temperature on the relevant thermophysical properties of air.
The correlation between Nusselt number and Rayleigh number is given as $\overline{\mathrm{Nu}}_L = 0.10\,\mathrm{Ra}_L^{0.25}$.
- With the help of $P$-$\theta$ (pressure-crank angle) diagram, compare the knock in SI and CI engines. Explain that "the factors which tend to prevent knock in SI engines in fact promote knock in CI engines".
- Describe the phenomenon of 'blowby losses'. What are the factors that increase the blowby losses? What are the effects of increased blowby losses on the engine performance?
- What are the advantages and disadvantages of supercritical pressure boilers as compared to that of subcritical boilers? Also, draw the Rankine cycle ($T$-$s$ diagram) for a steam power plant employing supercritical boiler with single stage of reheating.
- Derive the expression as given below for draught $h$ in mm of water column being created by a chimney of height $H$ metre:
$$h = 353H\left[\frac{1}{T_a} - \left(\frac{m_a+1}{m_a}\right)\frac{1}{T_g}\right]$$
where $m_a$ is mass of air supplied per kg of fuel, and $T_a$ and $T_g$ are ambient air and hot gas temperatures in Kelvin, respectively.
- What is the chemical name of R134a? Is R134a an ecofriendly refrigerant? Clarify.
- A single-cylinder, two-stroke, high-speed diesel engine working on 'dual cycle' has a compression ratio of 15 : 1. The engine takes in atmospheric air at 1 bar and 27 $^\circ$C. The maximum temperature in the cylinder is 1312 K. The cutoff ratio is 1.093. The engine has a bore of 200 mm and stroke length of 250 mm. The engine speed is 3000 r.p.m. Calculate the following:
(i) The cycle efficiency
(ii) The net work output per unit mass of air
(iii) The power output
(iv) The mean effective pressure
(v) The ratio of heat added in the constant-pressure process to that in the constant-volume process
Draw the $P$-$V$ and $T$-$s$ diagrams of the cycle.
For air, $\gamma = 1.4$, $R = 0.287$ kJ/kg-K.
- An ideal regenerative steam power cycle operates so that steam enters the turbine at 30 bar and 350 $^\circ$C, and exhausts at 0.1 bar. A single open feedwater heater is employed which operates at 5 bar. Compute the thermal efficiency of the cycle. The steam properties at 30 bar and 350 $^\circ$C are $h = 3115.3$ kJ/kg and $s = 6.7427$ kJ/kg-K.
Use Steam tables given at the end to get other properties.
- Why is vapour absorption refrigeration system considered to be a better option in comparison to vapour compression refrigeration system for large capacity refrigeration and air-conditioning plants?
- A two-stage turbine receives steam at 50 bar and 350 $^\circ$C. At 1.5 bar, the high-pressure stage exhausts and 12000 kg of steam per hour is taken at this stage for process heating purposes. The remainder steam is reheated to 250 $^\circ$C at 1.5 bar and then expanded through the low-pressure turbine to a condensate pressure of 0.05 bar. The power output from the turbine unit is to be 3750 kW. The isentropic efficiency of high-pressure stage is 0.84 and that of the low-pressure stage is 0.81. Calculate the rate of steam being generated per hour by the boiler.
Steam properties:
50 bar, 350 $^\circ$C: $h = 3068.4$ kJ/kg, $s = 6.4492$ kJ/kg-K
1.5 bar, 250 $^\circ$C: $h = 2972.65$ kJ/kg, $s = 7.8709$ kJ/kg-K
Use Steam tables given at the end to get other properties.
- (i) What is meant by effective temperature? List and explain briefly the factors which affect optimum effective temperature in air-conditioning. [10]
(ii) Explain psychrometric process of adiabatic mixing of two air streams. [10]
- Why is it necessary to cool IC engines? What are the disadvantages of overcooling an IC engine?
- The following data refers to a single-stage vapour compression refrigeration system:
Refrigerant = R134a
Condenser temperature = 35 $^\circ$C
Evaporator temperature = $-10$ $^\circ$C
Compressor motor speed = 2800 r.p.m.
Clearance ratio = 0.03
Swept volume = 269.4 $\mathrm{cm^3}$
Expansion index = 1.12
Compression isentropic efficiency = 75%
Condensate subcooling in condenser = 5 $^\circ$C
Draw $P$-$h$ diagram and determine the following:
(i) The capacity of the plant in TR
(ii) The power required in kW
(iii) The COP
(iv) The heat rejection to condenser
(v) The second law efficiency
The properties of R134a are given in the table:
| $T$ ($^\circ$C) | $P$ (bar) | Specific volume of saturated vapour $v_g$ ($\mathrm{m^3/kg}$) | Enthalpy $h_f$ (kJ/kg) | Enthalpy $h_g$ (kJ/kg) | Entropy $s_f$ (kJ/kg-K) | Entropy $s_g$ (kJ/kg-K) |
|---|---|---|---|---|---|---|
| $-10$ | 2.014 | 0.0994 | 186.7 | 392.4 | 0.9512 | 1.733 |
| 35 | 8.870 | - | 249.1 | 417.6 | 1.1680 | 1.715 |
Assume specific heat of liquid and vapour at 8.87 bar as 1.458 kJ/kg-K and 1.1 kJ/kg-K, respectively. The refrigerant at entry to compressor is in dry saturated state.
- (i) What are the important properties of lubricants used in IC engines? Discuss their significance. [10]
(ii) What are the advantages and disadvantages of the Indirect Injection (IDI) swirl chamber over the open-type Direct Injection (DI) combustion chamber in CI engines? [10]
- Calculate the critical pressure and throat area per unit mass flow rate of a convergent-divergent nozzle, expanding steam from 10 bar and dry saturated, down to atmospheric pressure of 1 bar. Assume that the inlet velocity is negligible and that the expansion is isentropic.
Use Steam tables given at the end to get the steam data.
The value of isentropic expansion index may be taken as 1.135.