Mains PYQs
UPSC Mains Mechanical Engineering paper 1 2024 questions
- A rod of length 2 m and weight 450 N rests on ground at one end. The other end is supported by a cord through which a force of 200 N is applied. What is the minimum angle $\alpha$ for which equilibrium is possible? The coefficient of static friction between the rod and the floor is 0.4:
[Figure] Rod of length 2 m (1 m + 1 m to the 450 N weight at midpoint), angle $\alpha$ with the ground, cord over a pulley at angle $\beta$ with 200 N force pulling horizontally, $\mu_s = 0.4$ at the floor.
- A shaft of span 1.5 m and diameter 20 mm is simply supported at the ends. It carries a 125 kg concentrated mass at midspan. If $E = 200$ GPa, calculate its fundamental frequency.
- Two thick washers are placed on the two ends of a copper tube and a steel bolt of pitch 1.8 mm is made to pass through these washers as shown in the figure below. The nut is tightened first with hand so that there are no stresses in the tube. Now, the nut is further tightened with the spanner through one-fourth of a turn. Calculate the axial stresses developed in the tube and the bolt. Young's modulus values for steel and copper are 200 GPa and 105 GPa, respectively:
[Figure] Washer, copper tube, steel bolt 12 mm dia, tube dimensions 14 mm and 20 mm, length 120 mm.
- Explain critical cooling rate using continuous cooling transformation (CCT) diagram and write its importance in hardening heat treatment of alloy steel.
- A single-cylinder reciprocating engine has speed 250 rpm, stroke 300 mm, mass of the reciprocating parts 60 kg and mass of the revolving parts 50 kg at 150 mm radius. If two-thirds of the reciprocating parts and all the revolving parts are to be balanced, find (i) the balance mass required at a radius of 400 mm and (ii) the residual unbalanced force when the crank has rotated 60° from top dead centre.
- Bodies A, B and C of weights 100 N, 200 N and 150 N, respectively are connected as shown. If released from rest, what would be their respective velocities after 1 s? The pulleys are massless:
[Figure] Pulley system with A, B (hanging from a movable pulley) and C on a 30° incline.
- The turning moment curve for one revolution of a multicylinder engine above and below the line of mean resisting torque are given by $-30, +360, -250, +300, -300, +250, -380, +260$ and $-210\ \mathrm{mm}^2$. The vertical and horizontal scales are 1 mm = 600 N-m and 1 mm = 5°, respectively. The fluctuation of speed is limited to $\pm 1.5\%$ of mean speed which is 250 rpm. The hoop stress in rim material is limited to $10\ \mathrm{N/mm}^2$. Neglecting the effect of boss and arms, determine the suitable diameter and cross-section of flywheel rim. The density of rim material is $7200\ \mathrm{kg/m}^3$. Assume width of rim equal to four times its thickness.
- Calculate the packing efficiency and packing density of carbon if mass of carbon atom is $1.992\times10^{-26}$ kg and unit cell side (a) is $3.57\times10^{-10}$ m. Assume crystal structure of carbon as diamond cubic.
- Show the loading on the beams corresponding to the bending moment diagrams shown below. The beams are simply supported at A and B:
[Figure] (i) Bending moment diagram with -1600 N-m at A and +800 N-m (parabolic) towards B, spans 3 m + 3 m. (ii) Bending moment diagram with -1500 N-m at A and -2300 N-m at B, span 3 m.
- A rectangular plate with a central circular hole of diameter 250 mm is subjected to two mutually perpendicular direct stresses of magnitudes $20\ \mathrm{MN/m}^2$ and $10\ \mathrm{MN/m}^2$ along the x and y directions, respectively. In addition, a shear stress of magnitude $7.5\ \mathrm{MN/m}^2$ acts on all the four planes on which the direct stresses act (see the figure below). The circular hole is deformed into the shape of an ellipse. If the value of Young's modulus of the material is $210\ \mathrm{GN/m}^2$ and Poisson's ratio is 0.3, find the lengths of the major and minor axes:
[Figure] Rectangular plate with central hole of 250 mm diameter, 20 MN/m^2 along x, 10 MN/m^2 along y, 7.5 MN/m^2 shear on all four edges.
- Compare different types of cast iron in respect of (i) form of carbon, (ii) micro-structure and (iii) mechanical properties.
- A governor of Hartnell type has each ball of weight 20 N and the lengths of vertical and horizontal arms of the bell crank lever are 125 mm and 65 mm, respectively. The fulcrum of the bell crank lever is at a distance of 100 mm from the axis of rotation. The maximum and minimum radii of rotation of the balls are 125 mm and 80 mm, and the corresponding equilibrium speeds are 325 rpm and 300 rpm, respectively. Find the stiffness of the spring and the equilibrium speed when the radius of rotation is 100 mm.
- Determine the deflection at a point 1 m from the left-hand end of the beam loaded as shown in the figure below. Use double integration method. The beam is having a constant flexural rigidity of 0.6 MN-m$^2$:
[Figure] Beam with 15 kN load at left end, support A (reaction $R_A$) at 0.6 m, 20 kN/m distributed load over 1.2 m, 15 kN point load at the end of the distributed load, then 1.2 m to support B (reaction $R_B$).
- Enumerate different types of cams and followers commonly used. State their relative merits and demerits.
- A cutting tool is used to machine alloy steel at cutting speed of 40 m/min. Considering the values of constants c and n for cutting tool material as 300 and 0.5, respectively as per tool-life equation, calculate the tool life in minutes. If the cutting speed is increased by 80%, then calculate the percentage change in tool life.
- The stepper motor of a point-to-point controlled NC machine has specification sensitivity of 3°/pulse. The pitch of the lead screw is 2.4 mm. Determine the expected positioning accuracy.
- A factory working in two shifts, each of 8 hours, produces 28000 tube lights using a set of workstations. Using this information, compute the actual cycle time of the plant operation. There are 6 tasks required to manufacture the tube light. The sum of all task times is equal to 10 seconds. How many workstations are required to maintain this level of production assuming that combining of tasks into those workstations is a feasible alternative?
- A car manufacturing unit uses large quantities of a component made of steel. The demand is continuous and inventory planning could be done independent of the production plan. The annual demand for the component is 2500 boxes. The company procures the item from a supplier at the rate of ₹ 1,250 per box. The company estimates the cost of carrying inventory to be 20 percent/unit/annum and the cost of ordering as ₹ 1,200 per order. The company works for 250 days in a year. How should the company design an inventory control system for this item? What is the total cost of the plan?
- A manufacturer of toys for children in the age group of 2 to 4 years commissioned a market research firm to understand the factors that influenced the demand for the product. After some detailed studies, the research firm concluded that the demand was a simple linear function of number of newlywed couples in the city. Based on this assumption, build a model for forecasting the demand for the product using the data in the table given below, which is collected from a residential area in a city:
| New Marriages (X) | Demand for Toys (Y) |
|---|---|
| 200 | 165 |
| 235 | 184 |
| 210 | 180 |
| 195 | 145 |
| 225 | 190 |
| 240 | 169 |
| 217 | 180 |
| 225 | 170 |
- A perfectly plastic material having yield strength of 300 MPa is subjected to extrusion at 400 °C. The extrusion speed is 300 mm/s. The extrusion process is done on billet of diameter 50 mm and length 300 mm. Extrusion reduces the diameter of billet from 50 mm to 20 mm. Assuming that the extrusion process is frictionless, determine the true strain, average true strain, ideal extrusion force and work done on billet during extrusion. The initial diameter of billet is significantly greater than the final diameter after extrusion.
- The data for the number of dissatisfied customers in a department store observed for 20 samples of size 300 are shown in the table below. Construct a suitable control chart for the collected data. Any out-of-control situation may be treated as the presence of some assignable cause, accordingly revise the control limits:
| Sample | No. of Dissatisfied Customers | Sample | No. of Dissatisfied Customers |
|---|---|---|---|
| 1 | 10 | 11 | 6 |
| 2 | 12 | 12 | 19 |
| 3 | 8 | 13 | 10 |
| 4 | 9 | 14 | 7 |
| 5 | 6 | 15 | 8 |
| 6 | 11 | 16 | 4 |
| 7 | 13 | 17 | 11 |
| 8 | 10 | 18 | 10 |
| 9 | 8 | 19 | 6 |
| 10 | 9 | 20 | 7 |
Management believes that the dissatisfaction rate is 2%, so establish control limits based on this value. Discuss whether the department can meet this goal. What actions would you recommend?
- List down different types of wastes indicated in JIT system. How are they connected with flow layout?
- An orthogonal cutting of metal is performed using cutting speed of 120 m/min, tool rake angle 5° and width of cut 5 mm. Cutting produces chip thickness 0.4 mm and generates main cutting and thrust forces of 600 N and 300 N, respectively. Considering uncut chip thickness as 0.2 mm, calculate the chip thickness ratio, friction force and percentage of total cutting energy used to overcome friction at chip-tool interface.
- A company produces both interior and exterior paints from raw materials M1 and M2. The following table provides the basic data of the problem:
| | Exterior Paint | Interior Paint | Maximum Daily Availability (tons) |
|---|---|---|---|
| Raw Material M1 | 6 | 4 | 24 |
| Raw Material M2 | 1 | 2 | 6 |
| Profit per ton (₹) | 4,00,000 | 3,20,000 | |
(Raw material per ton of paints, in tons, for the first two columns.)
A market survey indicates that the daily demand for interior paint cannot exceed that for exterior paint by more than 1 ton. Also the maximum daily demand for interior paint is 2 tons. This company wants to determine the optimum product mix of interior and exterior paints that maximizes the total daily profit. Comment on the optimal solution if the objective function is maximization of $Z = 480000x_1 + 320000x_2$.
- What are the elements of a quality costing system? How does an organization benefit from a quality costing system?
- Explain the principle of electric discharge machining (EDM) using suitable diagram. Describe the effect of process parameters of electric discharge machining on process performance characteristics such as material removal rate, tolerance and surface characteristics.
- XYZ corporation has given the following information on its capacity, sales and cost:
(i) Current capacity = 100000 units
(ii) At current level of operation, its margin of safety is 50% of its break-even point
(iii) Contribution margin P/V ratio = 25%
(iv) The unutilized capacity at present is 10000 units
(v) Sales price is ₹ 40 per unit
Based on the above information, determine the break-even point in sales volume, fixed costs, variable costs per unit and margin of safety in units.
- A company is interested in locating a new facility in a target market and would like to know the most appropriate place in the target market to locate the facility. There are four supply points A, B, C and D in the locality which will provide key inputs to the new facility. A two-dimensional grid map of the target market in which we would like to locate a new facility along with the distance coordinates of four supply points is shown in the figure below. The annual supply from these four points to the proposed facility is 200, 450, 175 and 350 tons, respectively:
[Figure] Grid map (X and Y axes in units) showing points A, B, C, D.
(Distance coordinates are in brackets)
| Supply Points | Coordinates (Units) | Annual Supply (tons) |
|---|---|---|
| A | (125, 550) | 200 |
| B | (350, 400) | 450 |
| C | (450, 125) | 175 |
| D | (700, 300) | 350 |
Identify the most appropriate point in the grid map to locate the new facility using centre of gravity model.