Mains PYQs
UPSC Mains Mechanical Engineering paper 1 2023 questions
- A heavy carriage wheel of weight W, and radius r is to be dragged over an obstacle of height h by a horizontal force P applied to the centre of the wheel. Show that P is slightly greater than $\dfrac{W \cdot \sqrt{2rh - h^2}}{r - h}$.
- A disc mounted on a shaft is having three masses of 6 kg, 5 kg and 4 kg, which are attached at a radial distance of 70 mm, 80 mm and 50 mm at the angular positions of $45^\circ$, $135^\circ$ and $240^\circ$ respectively. The angular positions are measured counter-clockwise from the reference line along the x-axis. Calculate the amount of countermass at the radial distance of 85 mm required for the static balance.
- From a balloon ascending with a velocity of 25 m/s above the surface of a lake, a stone is let fall and the sound of the splash is heard 5 seconds later. Find the height of the balloon when the stone was dropped, assuming that the velocity of sound is 340 m/s.
- What is the importance of the atomic packing factor ? Compute the atomic packing factor for the FCC crystal structure.
- A 1.5 m long shaft having diameter 2.0 cm is held at the ends by long bearings. The weight of a disc at the centre of the shaft is 20 kg. If the modulus of elasticity of the material of shaft is $2 \times 10^6\,\mathrm{kg/cm^2}$, then calculate the critical speed of the shaft in cycles per minute.
- In Figure 2(a), AB is a rigid bar, CE is a steel rod of 20 mm diameter and DF is a copper rod of 20 mm diameter. If the end A is hinged and a load of 30 kN acts at the free end B, find the stresses in the steel and copper rods and the reaction at A.
Given : $E_s = 200\,\mathrm{GN/m^2}$ and $E_c = 100\,\mathrm{GN/m^2}$
[Figure]
Figure 2(a): rigid bar AB horizontal with A hinged; steel rod CE of length 1 m above the bar at C; copper rod DF of length 1 m below the bar at D; AC = 1 m, CD = 2 m, DB = 1 m; 30 kN load acts downward at B.
- The length of each arm of a Porter governor is 350 mm. The lower arms are attached to a sleeve at a distance of 25 mm from the axis and the upper arms are pivoted on the axis of rotation. The load on the sleeve is 250 N and the weight of each ball is 25 N. If the radius of rotation of the balls is 125 mm at a speed of 225 rpm, then calculate the following:
(i) Speed of governor after the sleeve has lifted 55 mm
(ii) Effort
(iii) Power of the governor
- Discuss three reasons why ferrous alloys are used so extensively and also discuss three characteristics of ferrous alloys that limit their utilization.
- The coefficient of friction for all contacting surfaces in Figure 3(a) is 0.2. Does the 25 kg force move the block A up, hold it in equilibrium, or is it too small to prevent A from coming down and B from moving out ? The 25 kg force is exerted at the mid-plane of the block so that we can consider this a coplanar problem.
[Figure]
Figure 3(a): block A of 100 kg (0.6 m wide) against a vertical wall, resting on wedge B of 50 kg (0.6 m base, $15^\circ$ incline) on the floor; a 25 kg force pushes B horizontally toward the wall.
- A plane stress condition exists at a point in a loaded structure. The stresses have the magnitude and directions shown on the stress element of Figure 3(b). Calculate the stress acting on the planes obtained by rotating the element clockwise through an angle of $15^\circ$.
[Figure]
Figure 3(b): stress element with $P_1 = 80\,\mathrm{N/mm^2}$ (compressive, on the left and right faces), $P_2 = 20\,\mathrm{N/mm^2}$ (tensile, on the top and bottom faces) and shear stress $q = 30\,\mathrm{N/mm^2}$.
- Discuss microstructure and mechanical properties of pearlite, bainite and martensite.
- Two involute gears in mesh have pressure angle of $20^\circ$ and module of 6 mm. The number of teeth on pinion is 28 and the larger gear has 52 teeth.
Calculate the following:
(i) Contact ratio
(ii) Angle of action of gear wheel and pinion
(iii) Ratio of sliding velocity to rolling velocity at
(I) Starting of contact,
(II) Pitch point,
(III) End of contact.
Consider the addenda on pinion and gear wheel as equal to one module.
- A solid circular shaft made of steel is subjected to a bending moment of 12 kNm and a twisting moment of 16 kNm. In a simple uniaxial tensile test of the same material it gave the stress at yield point = $300\,\mathrm{N/mm^2}$. Assuming factor of safety = 2, estimate the minimum diameter required for the circular shaft using (i) Maximum Principal Stress theory, and (ii) Maximum Shear Stress theory.
- Write short notes on the following:
(i) Ceramics
(ii) Nano-materials
- In an electrochemical machining process of an iron surface using sodium chloride solution as electrolyte, following observations were made:
Specific resistance of the electrolyte = 5 $\Omega$ cm (ohm-cm)
Supply voltage = 15 V DC
Cross-sectional area of iron surface = 20 mm $\times$ 20 mm
Gap between the tool and workpiece = 0.3 mm
Use the following data for iron:
Valency = 2, Atomic weight = 55.85, and Density = $7860\,\mathrm{kg/m^3}$
Consider the current efficiency as 100% and Faraday's constant = 96540 Coulombs.
Calculate the material removal rate and electrode feed rate in the above mentioned electrochemical machining process.
- A laser beam with power intensity of $2 \times 10^5\,\mathrm{W/mm^2}$ falls on a stainless steel sheet. Find out the time required for the stainless steel surface to reach melting temperature, assuming that only 10% of the beam power is absorbed.
Use : Thermal conductivity = 0.27 W/cm-$^\circ$C
Volume specific heat = 3.36 J/cm$^3$-$^\circ$C
Melting point temperature = 1455$^\circ$C
- Discuss the trade-off between cost and quality considering various costs of conformance and costs of non-conformance.
- The corporation 'X' is designing its new assembly line. The line will produce 50 units per hour. The tasks, their times, and their predecessors are shown in the following table:
| Task | Immediate Predecessor | Task Time (sec.) |
|---|---|---|
| A | - | 55 |
| B | A | 30 |
| C | A | 22 |
| D | B | 35 |
| E | B, C | 50 |
| F | C | 15 |
| G | F | 5 |
| H | G | 10 |
(i) Draw the network diagram.
(ii) Compute the cycle time with a desired output of 50 units/hour.
(iii) Compute the theoretical number of work-stations and assign the task on the work-stations. Did you end up using more work-stations than the theoretical minimum ?
(iv) Compute the efficiency and balance delay of the line.
(Use longest time method)
- On the given data, perform regression analysis to forecast the demand for the 6$^\text{th}$ year, considering that the demand is increasing approximately exponentially.
($y = ae^{bx}$; where a and b are constants, x is the number of the year and y is forecasted demand)
| No. of the year | 1 | 2 | 3 | 4 | 5 |
|---|---|---|---|---|---|
| Demand (units) | 40 | 60 | 200 | 700 | 1000 |
- Following data were observed while machining two different work materials X and Y using a centre lathe machine:
| Work Material | Cutting Tool Life (min.) | Cutting Speed (m/min.) |
|---|---|---|
| X | 20 | 125 |
| X | 15 | 150 |
| Y | 45 | 250 |
| Y | 25 | 300 |
If work material X is standard material, then determine the relative machinability considering the tool life of 50 minutes as criterion.
- The work processing time and due date of five jobs are given in the following table. These five jobs are to be sequenced as per:
(i) First Come First Serve (FCFS)
(ii) Earliest Due Date (EDD)
(iii) Minimum Slack (SLACK)
(iv) Shortest Processing Time (SPT)
Which sequencing rule among these four rules will be recommended by you ?
| Jobs | Processing Time (days) | Due Date (days) |
|---|---|---|
| A | 5 | 10 |
| B | 10 | 15 |
| C | 2 | 5 |
| D | 8 | 12 |
| E | 6 | 8 |
- A company is producing pumps. The cost of the structure of a pump is as under:
Material cost : ₹ 1000/unit
Labour cost : ₹ 500/unit
Variable cost overheads : 50% of labour and material cost
If the fixed cost for the production of pumps amounts to ₹ 10,00,000 and selling price (S) varies as $S = 4D^2$, where D is demand in units, how many items will the company have to sell to reach break-even point ?
- (i) A tube is to be drawn as per the dimensions given in the following Figure 7(a)(i) showing die, plug and tube. Assuming the metal in work hardened condition with yield stress $1.40\,\mathrm{kN/mm^2}$, coefficient of friction for die as well as for plug is 0.15, calculate the drawing load and power of the motor required for drawing the tube with the speed of drawing 0.50 m/s. [10]
[Figure]
Figure 7(a)(i): die and plug with tube; die angle $15^\circ$, plug angle $10^\circ$, tube outer diameter $\phi$ 20 mm before drawing, inner diameter $\phi$ 18 mm, wall thickness 2.0 before and 1.5 after drawing (All dimensions are in 'mm').
(ii) Draw and label the surface roughness symbol, if the method of machining was milling, sample length 3.0 mm, direction of lay is perpendicular to the surface, machining allowance is 2 mm with roughness $R_a$ as 6.3 $\mu$m. Also, calculate the centre line average and root mean square values of surface roughness for the following measurements {figure 7(a)(ii)} taken over a sample length of 20 mm. [10]
[Figure]
Figure 7(a)(ii): surface profile over 20 mm with heights in $\mu$m at stations 1 to 8: 70, 35, 75, 20, 65, 40, 80, 50.
- The following information is given for the items procured and sold by a shopkeeper:
Annual Demand : 8000 units
Ordering Cost : ₹ 180/order
Holding Cost : 10% of the item cost
Following offers are given to the shopkeeper for different lot sizes:
| Lot Size | Unit Price (₹) |
|---|---|
| 1 - 999 | 22.00 |
| 1000 - 1499 | 20.00 |
| 1500 - 1999 | 19.00 |
| 2000 and above | 18.50 |
Check the feasibility of different offers using Economic Order Quantity and compare the total annual costs of the feasible offers.
- What are the key features of Total Quality Management to improve customer satisfaction through design, manufacture and delivery of quality products ?
- The following data represents the results of inspecting 50 units/day of personal computers produced by two processes A and B of a company for the past ten days.
| Sample No. | Process A: No. of Non-Conforming Units | Process B: No. of Non-Conforming Units |
|---|---|---|
| 1 | 5 | 8 |
| 2 | 6 | 7 |
| 3 | 7 | 8 |
| 4 | 5 | 9 |
| 5 | 4 | 10 |
| 6 | 6 | 11 |
| 7 | 5 | 15 |
| 8 | 7 | 8 |
| 9 | 9 | 9 |
| 10 | 6 | 7 |
Calculate control limits for both the processes A and B separately and also see if there is need for revision of control limits in any of the processes.
The company claims that 5 PCs may be non-conforming at most out of 50 produced. Perform hypothesis tests for each process using Z-distribution to determine whether the claim of the company is valid for both or not.
(Use Normal Distribution table)
- A medium carbon steel cylindrical rod is being machined under orthogonal cutting condition with an HSS cutting tool having rake angle as $12^\circ$.
While machining, following data were recorded:
Vertical component of cutting force = 1600 N
Horizontal component of cutting force = 1250 N
Chip thickness ratio = 0.25
Calculate the following for the above mentioned machining condition:
(i) Normal force on the rake face
(ii) Friction force along the rake face
(iii) Resultant cutting force
(iv) Coefficient of friction at chip tool interface
(v) Normal force on the shear plane
(vi) Shear force along the shear plane
- A manufacturing company wants to arrange work-centres A, B, C and D, so as to minimize inter-departmental parts handling costs. The flow of parts and existing work-centres layout are shown below:
Parts moved between work-centres
| | A | B | C | D |
|---|---|---|---|---|
| A | - | 400 | 500 | 50 |
| B | 300 | - | 200 | 0 |
| C | 0 | 0 | - | 700 |
| D | 0 | 0 | 0 | - |
Existing layout with distances
[Figure]
Four work-centres in a row, A, B, C, D, with 30 m between successive centres.
Suggest a modified layout.