Mains PYQs
UPSC Mains Mechanical Engineering paper 2 2022 questions
- Consider the system shown in Fig. 1(a). The two chambers initially have equal volumes of 28 litres and contain air ($C_p = 1.005\,\mathrm{kJ/kg\text{-}K}$ and $C_v = 0.717\,\mathrm{kJ/kg\text{-}K}$) and hydrogen ($C_p = 14.32\,\mathrm{kJ/kg\text{-}K}$ and $C_v = 10.17\,\mathrm{kJ/kg\text{-}K}$), respectively. The chambers are separated by a friction-less piston which is non-heat-conducting. Both the gases are initially at 140 kPa and 40 °C. Heat is added to the air side until the pressure of both the gases reaches 280 kPa. All outside walls of the chambers are insulated except for the surface where heat is added to air. Calculate the final temperature of the air.
[Figure] Q applied to Air on the left; H2 on the right; Insulation on outer walls; Non-heat-conducting piston between the chambers. Fig. 1(a)
- What is 'choked flow' in a convergent-divergent nozzle? Explain, with diagram, the effect of pressure ratio on exit velocity of compressible gas in a convergent-divergent nozzle.
- An axial flow compressor with inlet and outlet angles of 40° and 15°, respectively has been designed for 50% reaction. The compressor has a pressure ratio of 6 : 1 and overall isentropic efficiency of 0.80, when inlet static temperature is 41 °C. The blade speed and axial velocity are constant throughout. Assuming a value of 210 m/s for blade speed, find the number of stages required if the work done factor is 0.88 for all the stages. Take $C_p = 1.005\,\mathrm{kJ/kg\text{-}K}$ and $\gamma = 1.4$ for air.
- Hot water is flowing through a pipe made of cast iron having thermal conductivity of 52 W/m-°C, with an average velocity of 1.5 m/s. The inner and outer diameters of the pipe are 3 cm and 3.5 cm, respectively. The pipe passes through a 15 m long section of a basement whose temperature is 15 °C. The temperature of the water drops from 70 °C to 67 °C as it passes through the basement. The heat transfer coefficient on the inner surface of the pipe is 400 W/m$^2$-°C. Determine the combined convection and radiation heat transfer coefficient at the outer surface of the pipe.
- (i) Define the total and spectral black body emissive powers. How are they related to each other? [5]
(ii) Consider two identical bodies, one at 1000 K and the other at 1500 K. Which body emits more radiation in the shorter wavelength region? Which body emits more radiation at a wavelength of 20 µm? [5]
- 10 g of water at 20 °C is converted into ice at -10 °C at constant atmospheric pressure. Assuming the specific heat of liquid water to remain constant at 4.2 J/g-K and that of ice to be half of this value and taking the latent heat of fusion of ice at 0 °C to be 335 J/g, calculate the total entropy change of the system.
- A shaft having diameter of 5 cm rotates in a bearing made of cast iron. The shaft rotates at 4500 r.p.m. The bearing is 15 cm long, 8 cm outer diameter and has thermal conductivity of 70 W/m-K. There is a uniform clearance between the shaft and the bearing of 0.6 mm. The clearance is filled with a lubricating oil having thermal conductivity of 0.14 W/m-K and dynamic viscosity of 0.03 N-s/m$^2$. The bearing is cooled externally by a liquid, and its outer surface is maintained at 40 °C. Disregarding the heat conduction through the shaft and assuming only one-dimensional heat transfer, determine (i) the rate of heat transfer to the coolant, (ii) the surface temperature of the shaft and (iii) the mechanical power wasted by the viscous dissipation in the lubricating oil.
- Air ($C_p = 1.05\,\mathrm{kJ/kg\text{-}K}$, $\gamma = 1.38$) at 3 bar pressure and $T = 600\,\mathrm{K}$ is flowing with a velocity of 180 m/s inside a 20 cm diameter duct. Calculate the-
(i) mass flow rate;
(ii) stagnation temperature;
(iii) Mach number;
(iv) stagnation pressure assuming flow to be (1) compressible and (2) incompressible.
- (i) How do the specific work output and efficiency vary with pressure ratio in a gas turbine?
(ii) Prove that the efficiency of a gas turbine corresponding to the maximum work done in a Brayton cycle is given by the relation
$$\eta_{w\,\max} = 1 - \frac{1}{\sqrt{t}}$$
where $t$ is the ratio of the maximum and minimum temperatures.
- A solar collector, as shown in Fig. 3(b) below, having dimensions as 1 m wide and 5 m long, has constant spacing of 3 cm between the glass cover and the collector plate. Air enters the collector at 30 °C and at a rate of 0.15 m$^3$/s through the 1 m wide edge and flows along the 5 m long passageway. If the average temperatures of the glass cover and the collector plate are 20 °C and 60 °C, respectively, determine (i) the net rate of heat transfer to the air in the collector and (ii) the temperature rise of air as it flows through the collector.
[Figure] Air at 30 °C, 0.15 m$^3$/s; 3 cm spacing; Collector plate at 60 °C; Glass cover at 20 °C; Insulation. Fig. 3(b)
The properties of air at 1 atm and an estimated average temperature of 35 °C may be taken as :
$\rho = 1.145\,\mathrm{kg/m^3}$, $k = 0.02625\,\mathrm{W/m\text{-}°C}$, $\nu = 1.655\times10^{-5}\,\mathrm{m^2/s}$,
$C_p = 1007\,\mathrm{J/kg\text{-}°C}$, $\mathrm{Pr} = 0.7268$
- A windshield of a car, having dimensions as 0.6 m high and 1.8 m long, is electrically heated and is subjected to parallel winds at 1 atm, 0 °C and 80 km/hr. The electrical power consumption is observed to be 50 W, when the exposed surface temperature of the windshield is 4 °C. Disregarding the radiation and heat transfer from the inner surface and using the momentum heat transfer analogy, determine the drag force the wind exerts on the windshield. The properties of air at 0 °C and 1 atm may be taken as :
$\rho = 1.292\,\mathrm{kg/m^3}$, $C_p = 1.006\,\mathrm{kJ/kg\text{-}K}$, $\mathrm{Pr} = 0.7362$
- A single-stage impulse turbine rotor has a mean blade ring diameter of 500 mm and rotates at a speed of 10000 r.p.m. The nozzle angle is 20° and the steam leaves the nozzles with a velocity of 900 m/s. The blades are equiangular and the blade friction factor is 0.85. Construct velocity diagrams for the blades and determine the inlet angle of the blades for shockless entry of steam. Also, determine (i) the diagram power for a steam flow of 750 kg/hr, (ii) the diagram efficiency, (iii) the axial thrust and (iv) the loss of kinetic energy due to friction.
- (i) Explain the effect of impeller blade shape on the performance of a centrifugal compressor with the help of an exit velocity diagram and pressure ratio-mass flow rate curve.
(ii) Discuss the phenomena of surging and choking in centrifugal compressors.
- A shell and tube heat exchanger operates with two shell passes and four tube passes. The shell side fluid is ethylene glycol, which enters at 140 °C and leaves at 80 °C with a flow rate of 4500 kg/hr. Water flows in the tubes, entering at 35 °C and leaving at 85 °C. The overall heat transfer coefficient for this arrangement is 850 W/m$^2$-°C. Calculate the flow rate of water required and the area of the heat exchanger. The specific heat of ethylene glycol may be taken as 2.742 J/g-°C and the specific heat of water may be taken as 4.175 J/g-°C. For NTU relations, the following figure may be used.
[Figure] Shell and tube heat exchanger: Shell fluid $(mc)_s = C_s$, Tube fluid $(mc)_t = C_t$, Two shell passes, 4, 8, 12, etc., tube passes. Chart of effectiveness $\varepsilon$, % (0 to 100) against number of transfer units, $\mathrm{NTU_{max}} = AU/C_{\min}$ (0 to 5), with curves for $C_{\min}/C_{\max}$ = 0, 0.25, 0.50, 0.75, 1.00.
- Can alcohols be used as fuel in IC engine? Explain with advantages and disadvantages.
- A water-filled reactor with a volume of 1 m$^3$ is at 20 MPa and 360 °C, and is placed inside a containment room as shown in Fig. 5(b). The room is well-insulated and initially evacuated. Due to a failure, the reactor ruptures and the water fills the containment room. Find the minimum room volume so that the final pressure does not exceed 200 kPa.
[Use steam table data given at the end of the Paper]
[Figure] Reactor inside a Containment room. Fig. 5(b)
- Using a schematic and $T$-$s$ diagram, explain how with perfect regeneration for a simple steam power plant (Rankine) cycle, thermal efficiency can approach Carnot efficiency.
- Discuss the effect of the following parameters on the performance of a vapor compression refrigeration system with the help of $p$-$h$ diagram :
(i) Suction pressure
(ii) Delivery pressure
(iii) Subcooling of liquid
(iv) Superheating of vapors
- The room air is recirculated at the rate of 40 m$^3$ per minute and the outdoor air enters a cooling coil of an air conditioner at 32 °C DBT and 18 °C WBT. The effective surface temperature of the coil is 4.5 °C. The surface area of the coil is such as would give 12 kW of refrigeration with the given entering conditions of air. Determine the DBT and WBT of the air leaving the coil and the coil bypass factor.
[Psychrometric chart is given at the end of this Paper]
- A four-cylinder diesel engine with swept volume of 0.98 litre is tested on a performance bed. The engine running at a speed of 2500 r.p.m. against a brake with arm of 0.3 m produces brake load of 190 N with fuel consumption of 6.8 litres/hr. The calorific value of fuel is 45000 kJ/kg and specific gravity of fuel is 0.82. A Morse test is carried out on the engine by cutting off the fuel supply of individual cylinder in the order 1, 2, 3, 4 with corresponding brake loads 131 N, 135 N, 133 N and 137 N, respectively. Calculate the b.p., b.m.e.p., brake thermal efficiency, b.s.f.c., i.p., mechanical efficiency and i.m.e.p. of the engine at test speed.
- A power plant operates on a regenerative steam cycle with one closed feedwater heater. Steam enters the first turbine stage at 125 bar, 500 °C and expands to 10 bar, where some of the steam is extracted and diverted to the closed feedwater heater. Condensate exiting the feedwater heater as saturated liquid at 10 bar passes through a trap into the condenser. The feedwater exits the heater at 120 bar with a temperature of 170 °C. The condenser pressure is 0.06 bar. Assuming isentropic turbine and pump work, determine the thermal efficiency of the cycle. At 125 bar, 500 °C for steam, $h = 3343.6\,\mathrm{kJ/kg}$ and $s = 6.4651\,\mathrm{kJ/kg\text{-}K}$.
[Use steam tables provided at the end of this Paper]
- Explain NH$_3$-water vapor absorption refrigeration system with a neat diagram. What are the desired properties of refrigerant-absorber combination?
- (i) Briefly discuss HC, CO and NO$_x$ emission formation in SI engine. Explain the dependence of these emissions on equivalence ratio with a neat diagram. [10]
(ii) An IC engine working on an ideal Otto cycle has AFR of 15 : 1 and compression ratio of 9 : 1. The pressure and temperature at the start of compression are 1 bar and 27 °C, respectively. Find the maximum temperature and pressure of the cycle. Assume that compression process follows the law $pV^{1.33} = C$, the calorific value of fuel is 43000 kJ/kg and $C_v$ of working fluid is $0.717\,\mathrm{kJ/kg\text{-}K}$. [10]
- A food processing room has a very high latent heat load and is required to be air conditioned as per the following data :
Room design conditions : 20 °C DBT, 60% RH
Outside conditions : 45 °C DBT, 30 °C WBT
Room sensible heat : 35 kW
Room latent heat : 20 kW
The ventilation air requirement is 90 cmm
Determine the (i) ventilation load, (ii) room and effective sensible heat factors and (iii) ADP and amount of reheat for economical design. Assume bypass factor of the coil as 0.05.
[Psychrometric chart is given at the end of this Paper]
- Prove mathematically that for maximum discharge through a chimney of a certain height and cross-section, the absolute temperature of gases bears a certain ratio to the absolute temperature of the outside atmosphere, in case of natural draught of a boiler.
- A VCR cycle refrigerator driven by a 60 kW compressor has a COP of 6.0. The enthalpies of saturated liquid and saturated vapor refrigerant at condenser temperature of 35 °C are 114.95 kJ/kg and 283.89 kJ/kg, respectively. The saturated refrigerant vapor leaving evaporator has an enthalpy of 275.76 kJ/kg. Find the temperature of refrigerant at the exit of compressor. The $C_p$ of refrigerant is $0.62\,\mathrm{kJ/kg\text{-}K}$.
- In a combined gas turbine-steam turbine power plant, the exhaust gas from the open-cycle gas turbine is the supply gas to the steam generator of the steam cycle at which additional fuel is burnt in the gas. The pressure ratio for the gas turbine is 7.5, the air inlet temperature is 15 °C and the maximum temperature is 750 °C. Combustion of additional fuel raises the gas temperature to 750 °C and the gas leaves the steam generator at 100 °C. The steam is supplied to the steam turbine at 50 bar and 600 °C and the condenser pressure is 0.1 bar. The total power output of the plant is 200 MW. The calorific value of the fuel burnt is 43.3 MJ/kg. Neglecting the effect of the mass flow rate of fuel on the air flow, determine (i) the flow rate of air and steam required, (ii) the power outputs of the gas turbine and steam turbine, (iii) the thermal efficiency of the combined plant and (iv) the air-fuel ratio. Take $C_p = 1.11\,\mathrm{kJ/kg\text{-}K}$ and $\gamma = 1.33$ for combustion gases; and $C_p = 1.005\,\mathrm{kJ/kg\text{-}K}$ and $\gamma = 1.4$ for air. Neglect pump work. Condensate enthalpy at 0.1 bar = 192 kJ/kg.
[Mollier diagram is attached in Page No. 14]
- Two vapor power cycles are coupled in series where heat lost by one is absorbed by the other completely. If $\eta_1$ is the thermal efficiency of the topping cycle and $\eta_2$ is the thermal efficiency of the bottom cycle, determine the efficiency of the combined cycle in terms of these efficiencies. Assume cycles to be reversible.