Mains PYQs
UPSC Mains Mechanical Engineering paper 1 2022 questions
- A slider-crank mechanism with crank radius 60 mm and connecting rod length 240 mm is shown in Figure 1(a). The crank is rotating with a uniform angular speed of 10 rad/s, counterclockwise. For the given configuration, determine the speed of the slider. A and B in Figure 1(a) are at the same horizontal level.
[Figure]
Figure 1(a): crank OA = 60 (at A, pivot on ground), connecting rod OB = 240, angle at O is 90 degrees, slider at B on the ground line.
- In a complex two-dimensional stress system, the maximum and minimum principal stresses are found to be 160 MPa tensile and 80 MPa compressive. The material elastic limit is 300 MPa in a simple tension test. Find factor of safety using the following theories:
(i) Maximum principal stress theory
(ii) Maximum shear stress theory
(iii) Maximum distortion energy theory
- A pipe with external forces is shown in Figure 1(c). The loads 300 N, 200 N, and 900 N are acting at the centres of pipe sections as shown in the figure. Find the resultant of force system at point A shown in the figure.
[Figure]
Figure 1(c): labels 20 m, 8 m, 10 m; loads 200 N, 900 N, 300 N, 500 N, 600 N, 400 N; axes x, y, z with A at the wall.
- Compare thermosetting and thermoplastic types of plastics in terms of properties, response to heating and applications.
- Two meshing spur gears with pressure angle of the involute teeth being 20° have addendum equal to one module. The pinion has 14 teeth and the larger gear has 54 teeth. Does the interference occur ? If it occurs, what should be the change in the pressure angle in order to eliminate interference ? Take standard module = 10 mm.
- A 20 mm diameter shaft is subjected to a torque of 80 Nm and a downward bending moment of 100 Nm at the centre. Draw the state of stress on the bottom surface of the shaft at the centre and find principal stresses and shear stress at the centre of the bottom surface. What is the angle of shear plane ?
- What is Atomic Packing Factor of a crystal structure ? Calculate the atomic packing factor of aluminium assuming atoms to be of spherical shape with atomic radius 'R'.
- The cranks of a three-cylinder single acting engine are set equally at 120°. The engine speed is 540 rpm. The turning moment diagram for each cylinder is a triangle for the power stroke with a maximum torque of 100 Nm at 60° after dead-centre of the corresponding crank. On the return stroke, the torque is sensibly zero.
Determine the:
(i) power developed by the engine
(ii) coefficient of fluctuation of speed if the flywheel has a mass of 7.5 kg with a radius of gyration of 65 mm
(iii) coefficient of fluctuation of energy
(iv) maximum angular acceleration of the flywheel
- A thin cylinder of diameter 200 mm and length 1000 mm is subjected to an internal pressure of 10 MPa. The allowable stress of the material is 200 MPa and Young's modulus is 200 GPa. Determine the thickness, hoop and longitudinal strains under the given pressure.
- A beam carries a uniformly distributed load of 360 N/m over the entire span together with a concentrated load of 400 N at the extreme left. The beam is having a span of 10 m and is supported at two points 7 m apart. The supports are so chosen, that each support carries half the total load. Draw the shear force and bending moment diagrams after obtaining the maximum bending moment and points of contraflexure.
- In a Hartnell governor, the lengths of ball and roller arms of the bell crank lever are 100 mm and 80 mm respectively. Each ball has a mass of 1.5 kg. The extreme radii of rotation of the balls are 90 mm and 140 mm. The minimum equilibrium speed is 840 rpm and the maximum equilibrium speed is 5% greater than this. Assuming the sleeve to be of negligible mass and neglecting friction and obliquity of arms, determine:
(i) Spring stiffness
(ii) Initial compression of the central spring
(iii) Equilibrium speed corresponding to radius of rotation of 130 mm
- An automobile weighing 15 kN is moving at a speed of 100 km per hour. The dynamic coefficient of friction between the rubber tyre and concrete road is 0.60. When the driver jams on his brakes, the car goes into skid in the direction of motion. What is the distance the car will move before it comes to rest when
(i) the road is flat,
(ii) the road is 7° upward inclination,
(iii) the road is 7° downward inclination ?
- Explain the principle of annealing with the help of Continuous Cooling Transformation (CCT) diagram. Write the purpose and applications of annealing heat treatment.
- A shaft carries four masses A, B, C and D which are in complete balance. Masses C and D make angles of 90° and 210° respectively with that of mass B in the counterclockwise direction. The rotating masses A, B, C and D can be assumed to be concentrated at radii of 360 mm, 480 mm, 240 mm and 300 mm respectively. The masses B, C and D are 15 kg, 25 kg and 20 kg respectively and the planes containing B and C are 300 mm apart. Determine the following:
(i) Mass A and its angular position
(ii) Positions of planes A and D
- An HSS drill during its life can drill 150 through holes in a 10 mm thick brass plate at a drill speed of 400 rpm. Another drill of same type can make only 75 holes when the drill speed is increased to 600 rpm. How many holes will be produced by another drill of same type if its speed is raised to 800 rpm ? Take the feed in all the cases as same.
- Write the functions of coating on Shielded Metal Arc Welding (SMAW) electrode.
- Discuss the Expansionist strategy and Wait-and-See strategy for capacity timing and sizing concerning the capacity planning.
- A product is to be processed from its raw form to finished form through a number of workstations. The production lead time is given as 3 days. The daily demand requirement is 500 units. Safety stock is required for one day. Container's capacity is 400 units. Determine the number of Kanbans (containers) required.
- Derive the expression for Reorder point when demand is variable and lead time is constant. Suppose the average demand is 18 units per week with a standard deviation of 5 units. The lead time is constant at 2 weeks. Determine the safety stock and reorder point if management wants a 95% customer service level. (Refer Standard Normal Distribution table given on the last page)
- During turning of a steel rod of 100 mm diameter, at a speed of 600 rpm, feed of 0.32 mm/rev and 3 mm depth of cut by a tool of the following geometry: inclination angle 0°, orthogonal rake angle -12°, and principal cutting edge angle ($\phi$) 60°, the following have been observed:
Main cutting force component $P_z$ = 1000 N
Radial cutting force component $P_y$ = 200 N
Chip thickness = 0.75 mm
Using Merchant's theory, determine the force along the rake surface F, force acting perpendicular to the rake surface N, coefficient of friction between the chip-tool interface, shear force $F_s$ and cutting power consumption. Power consumption due to feed motion may be neglected.
- (i) State the sequence and purpose of different types of rolling passes, used for rolling flats and plates. [5]
(ii) A steel plate of 200 mm width and 30 mm thickness is rolled using two-stage rolling mill where diameter of each roller is 400 mm. Rolling is performed at 60 rev/min of roll speed to reduce thickness of steel strip from 30 mm to 26 mm. Average flow stress of metal during rolling is expressed by
$\delta_f=\dfrac{K\varepsilon^n}{1+n}$
where
n = strain hardening coefficient
K = strength coefficient, MPa
$\varepsilon$ = true strain
Consider strength coefficient of metal (K) is 300 MPa and strain hardening coefficient (n) is 0.2 and coefficient of friction between strip and roll during rolling is 0.15.
Calculate:
(I) Draft in mm
(II) Maximum achievable draft for above condition of rolling in mm
(III) Average flow stress in MPa
(IV) Rolling force in Newton
(Neglect all other possibilities related to rolling) [15]
- Write the contributions of Walter A. Shewhart, W. Edwards Deming, Joseph M. Juran, Philip B. Crosby, and K. Ishikawa in the area of quality management.
- A firm has identified four operations, which are to be conducted in succession for an order to be processed. The tolerance and mean time of each operation are given in the following table. Tolerance is independent of each other and the time is normally distributed.
| Operation | Mean Time (hours) | Tolerance (hours) |
|---|---|---|
| 1 | 7 | 7 ± 0.6 |
| 2 | 5 | 5 ± 0.6 |
| 3 | 9 | 9 ± 0.8 |
| 4 | 6 | 6 ± 0.3 |
(i) Find the natural tolerance limits for order completion time.
(ii) If the company sets a goal of 27.5 hours, what proportion of the orders will fail to satisfy the goal ?
(iii) Find an appropriate capability index and comment.
(iv) Using a technique, management has improved the operation 3 to a mean time of 8 hours. What proportion of the orders will now meet the goal ?
(Use Standard Normal Distribution table given on the last page)
- (i) Discuss the factors influencing the facility location selection. [10]
(ii) For expansion of a car manufacturing plant, three new locations are to be considered based on three factors:
Availability of labour, Proximity to the suppliers, and Proximity to the markets.
The weightage of these factors are given as 40%, 35%, and 25% respectively. The rating (on 100-point scale) of the locations against these factors are given in the following table:
| Location | Availability of labour | Proximity to the suppliers | Proximity to the markets |
|---|---|---|---|
| X | 70 | 60 | 45 |
| Y | 60 | 45 | 90 |
| Z | 55 | 95 | 50 |
Find the best and worst location for the new plant. [10]
- Spot welding of two steel sheets each of 1 mm thickness is performed using 20,000 A welding current supplied for 0.15 seconds. Assume that:
(i) interface contact resistance is 200 micro-ohms,
(ii) heat required for melting unit volume of steel is 10 J/mm$^3$, and
(iii) only 60% of heat generated is used for melting of metal at the interface.
Calculate:
(I) Heat generated, J
(II) Volume of the weld nugget, mm$^3$
- (i) Discuss the mechanism of material removal in ultrasonic machining. [10]
(ii) What are the different parameters affecting the material removal rate in ultrasonic machining ? Show the variation of material removal rate with respect to these parameters using suitable schematic. [10]
- (i) Discuss the ABC, VED and SDE classification of inventory items. [10]
(ii) A plastic moulding company provides the following details of various products in terms of annual demand and unit cost. Classify the products in A, B and C categories. [10]
| Item Code # | Annual Demand | Cost/Unit (₹) |
|---|---|---|
| XA-101 | 400 | 4.00 |
| XA-102 | 300 | 5.00 |
| XA-103 | 120 | 3.00 |
| XA-104 | 80 | 2.00 |
| XA-105 | 50 | 2.50 |
| XA-106 | 40 | 1.50 |
| XA-107 | 20 | 2.20 |
| XA-108 | 15 | 32.00 |
| XA-109 | 8 | 51.80 |
| XA-110 | 6 | 42.00 |
| XA-111 | 5 | 3.00 |
- Discuss the various steps used in sourcing of a product or service. Also, mention the name of the factors influencing the sourcing decision.