Mains PYQs
UPSC Mains Mechanical Engineering paper 2 2020 questions
- Air enters the compressor of a gas turbine plant at ambient conditions of 100 kPa and $25\,^\circ\mathrm{C}$ with negligible velocity, and exits at 1 MPa and $347\,^\circ\mathrm{C}$ with a velocity of $90\,\mathrm{m/s}$. The compressor is cooled at a rate of $1500\,\mathrm{kJ/min}$ and the power input to the compressor is $250\,\mathrm{kW}$. Determine the mass flow rate of air through the compressor. For air, consider $C_p = 1.005\,\mathrm{kJ/kg\text{-}K}$, $C_v = 0.717\,\mathrm{kJ/kg\text{-}K}$ and $R = 0.287\,\mathrm{kJ/kg\text{-}K}$.
- Consider the base plate of an $800\,\mathrm{W}$ household electric iron with thickness of $L = 0.6\,\mathrm{cm}$, base area $= 160\,\mathrm{cm}^2$ and thermal conductivity $k = 60\,\mathrm{W/m\text{-}K}$. The inner surface of the base plate is subjected to uniform heat flux generated by the resistance heater inside. When steady operating conditions are reached, the outer surface temperature of the plate is measured to be $112\,^\circ\mathrm{C}$. Disregarding any heat loss through the upper part of the iron-
(i) express the differential equation and boundary conditions for steady one-dimensional heat conduction through the plate;
(ii) obtain a relation for the variation of temperature in the base plate by solving the differential equation;
(iii) evaluate the inner surface temperature.
- Derive an appropriate equation to show that a divergent duct acts as a supersonic nozzle.
- A reversible engine works between three thermal reservoirs $A$, $B$ and $C$. The engine absorbs an equal amount of heat from the thermal reservoirs $A$ and $B$ kept at temperatures $T_A$ and $T_B$ respectively, and rejects heat to the thermal reservoir $C$ kept at temperature $T_C$. The efficiency of the engine is $\alpha$ times the efficiency of the reversible engine, which works between the two reservoirs $A$ and $C$. Prove that $\dfrac{T_A}{T_B} = (2\alpha - 1) + 2(1-\alpha)\dfrac{T_A}{T_C}$.
- When does reheating of steam become necessary in Rankine cycle? With the help of $T$-$s$ diagram, explain the effect of reheating on the Rankine cycle output and efficiency.
- Consider a $3\,\mathrm{m}$ diameter spherical tank that is initially filled with liquid nitrogen at 1 atm and $-196\,^\circ\mathrm{C}$. The tank is exposed to ambient air at $15\,^\circ\mathrm{C}$ with a combined convective and radiative heat transfer coefficient of $35\,\mathrm{W/m^2\text{-}K}$. The temperature of the thin-shelled spherical tank is observed to be almost the same as the temperature of the nitrogen inside. Determine the rate of evaporation of the liquid nitrogen in the tank as a result of the heat transfer from the ambient air if the tank is (i) not insulated, (ii) insulated with $5\,\mathrm{cm}$ thick fiberglass wool insulation ($k = 0.035\,\mathrm{W/m\text{-}K}$) and (iii) insulated with $2\,\mathrm{cm}$ thick superinsulation which has an effective thermal conductivity of $0.00005\,\mathrm{W/m\text{-}K}$. Consider the heat of vaporization of liquid nitrogen as $198\,\mathrm{kJ/kg}$ and its density as $810\,\mathrm{kg/m^3}$ at 1 atm.
- The mass flow rate of steam flowing in a pipeline is measured with the help of a well-insulated Venturi meter. Dry saturated steam at $7.0$ bar enters the Venturi. The pressure at the throat of the Venturi is measured to be $3.6$ bar. The inlet and throat diameters of the Venturi are $538.5\,\mathrm{mm}$ and $75\,\mathrm{mm}$ respectively. The velocity of steam at the inlet to the Venturi is $10\,\mathrm{m/s}$. Calculate the mass flow rate of steam neglecting friction. (The properties of steam are to be taken from the steam table as given below) :
Properties of Saturated Steam
| Pressure, P (bar) | $t_{sat}$ (°C) | $v_f$ (m^3/kg) | $v_g$ (m^3/kg) | $h_f$ (kJ/kg) | $h_g$ (kJ/kg) | $s_f$ (kJ/kg-K) | $s_g$ (kJ/kg-K) |
|---|---|---|---|---|---|---|---|
| 3.6 | 140.0 | 0.00108 | 0.511 | 588.6 | 2733.7 | 1.738 | 6.931 |
| 7.0 | 165.0 | 0.001108 | 0.273 | 697.2 | 2763.5 | 1.992 | 6.708 |
- Air enters a compressor in steady flow at $140\,\mathrm{kPa}$, $17\,^\circ\mathrm{C}$ and $70\,\mathrm{m/s}$ and leaves at $350\,\mathrm{kPa}$, $127\,^\circ\mathrm{C}$ and $110\,\mathrm{m/s}$. The environment is at $7\,^\circ\mathrm{C}$. Calculate per kg of air for (i) the actual amount of work required, (ii) the minimum work required and (iii) the irreversibility of the process. For air, take $C_p = 1.005\,\mathrm{kJ/kg\text{-}K}$ and $R = 0.287\,\mathrm{kJ/kg\text{-}K}$.
- One stage comprising a pair of blade rings of a 50 percent reaction axial flow steam turbine has a mean ring diameter of $140\,\mathrm{cm}$. The blade to steam speed ratio is $0.7$. The speed of rotation is $3000\,\mathrm{r.p.m.}$ Determine the required entrance angle for the blading if the exit angle is $20^\circ$. Also, determine the work done per kg of steam flowing per second and the diagram efficiency. Calculate the percentage increase in diagram efficiency if the blades are designed for, and run at the best theoretical speed corresponding to the optimum operating condition, for the given steam speed and the exit angle.
- (i) Establish the relation between 1st law efficiency, 2nd law efficiency and Carnot efficiency. [5]
(ii) A reversible heat engine operates between two thermal reservoirs of $1000\,^\circ\mathrm{C}$ and $40\,^\circ\mathrm{C}$. The engine drives a reversible refrigerator operating between $40\,^\circ\mathrm{C}$ and $-10\,^\circ\mathrm{C}$. The amount of heat transfer to the engine is $4000\,\mathrm{kJ}$ and a net amount of work output of $1000\,\mathrm{kJ}$ is obtained from the combined engine-refrigerator system. Determine (1) the amount of heat transfer to the refrigerator and (2) the net amount of heat transfer to $40\,^\circ\mathrm{C}$ reservoir. [15]
- A $2\,\mathrm{m} \times 3\,\mathrm{m}$ flat plate is suspended in a room and subjected to air flow parallel to its surfaces along its $3\,\mathrm{m}$ long side. The free stream temperature and velocity of air are $20\,^\circ\mathrm{C}$ and $7\,\mathrm{m/s}$ respectively. The total drag force acting on the plate is measured to be $0.86\,\mathrm{N}$. Determine the average convective heat transfer coefficient for the plate.
The properties of air at $20\,^\circ\mathrm{C}$ and 1 atm are $\rho = 1.204\,\mathrm{kg/m^3}$, $C_p = 1.007\,\mathrm{kJ/kg\text{-}K}$, $\mathrm{Pr} = 0.7309$.
- A frictionless piston/cylinder is loaded with a linear spring (as shown in the figure below) having a spring constant of $100\,\mathrm{kN/m}$, and the piston cross-sectional area is $0.1\,\mathrm{m^2}$. The cylinder having an initial volume of $20\,\mathrm{L}$ contains air at $200\,\mathrm{kPa}$ and ambient temperature $300\,\mathrm{K}$. There exists a stop in the cylinder which prevents its volume from exceeding $50\,\mathrm{L}$. A valve connects the cylinder to an air supply line flowing air at $800\,\mathrm{kPa}$, $325\,\mathrm{K}$. The valve is now opened, allowing air to flow in until the cylinder pressure and temperature reach $800\,\mathrm{kPa}$ and $350\,\mathrm{K}$ respectively. The valve is then closed and the process ends. At the final state does the piston reach the stop? Calculate the heat transfer during the process. Take $C_p = 1.005\,\mathrm{kJ/kg\text{-}K}$ and $R = 0.287\,\mathrm{kJ/kg\text{-}K}$ for air :
[Figure]
- A counter-flow double-pipe heat exchanger is to heat water from $20\,^\circ\mathrm{C}$ to $80\,^\circ\mathrm{C}$ at a rate of $1.2\,\mathrm{kg/s}$. The heating is to be accomplished by geothermal water available at $160\,^\circ\mathrm{C}$ at a mass flow rate of $2\,\mathrm{kg/s}$. The inner tube is thin-walled and has a diameter of $1.5\,\mathrm{cm}$. If the overall heat transfer coefficient of the heat exchanger is $640\,\mathrm{W/m^2\text{-}K}$, determine the length of the heat exchanger required to achieve the desired heating. Take specific heat of water and geothermal fluid as $4.18\,\mathrm{kJ/kg\text{-}K}$ and $4.31\,\mathrm{kJ/kg\text{-}K}$ respectively.
- Explain, with the help of velocity triangles, why centrifugal fans with backward-curved blading are used for forced draught fans, and centrifugal fans with forward-curved blading are used for induced draught fans in a steam power plant.
- Give a comparative statement in the form of a table of the various factors desired to be high or low which tend to reduce knock in SI and CI engines.
| Sl. No. | Factor | SI engine (High/Low) | CI engine (High/Low) |
|---|---|---|---|
| | | | |
- The operating temperatures of a simple vapour absorption refrigeration system are-generator $100\,^\circ\mathrm{C}$; condenser and absorber $45\,^\circ\mathrm{C}$; evaporator $2\,^\circ\mathrm{C}$. The system has refrigeration capacity of $125\,\mathrm{kW}$ and heat input to the system is $180\,\mathrm{kW}$. The solution pump work is negligible.
(i) Find the COP of the system and total heat rejection rate from the system.
(ii) An inventor claims that by improving the design of all the components of the above system, he could reduce the heat input to the system by $90\,\mathrm{kW}$, while keeping the refrigeration capacity and operating temperature same as before. Examine the validity of the claim.
- An axial flow fan operates at $1200\,\mathrm{r.p.m.}$ The blade tip diameter is $1.1\,\mathrm{m}$ and hub diameter is $0.8\,\mathrm{m}$. The blade inlet and exit angles are $30^\circ$ and $60^\circ$ respectively with respect to the plane of rotation. Inlet guide vanes give the absolute flow entering the rotor at an angle of $60^\circ$ with the plane of rotation. There is no change in the axial component of velocity across the rotor. Determine (i) the volume flow rate through the fan and (ii) the minimum torque and power needed to drive the fan. Take the density of air as $1.225\,\mathrm{kg/m^3}$.
- On the basis of 1-D isentropic flow, show that in a duct of varying area, the Mach number $M$ at any section is related to the area $A$ of the section by
$$\frac{A}{A^*} = \frac{1}{M}\left[\frac{2}{\gamma+1}\left(1+\frac{\gamma-1}{2}M^2\right)\right]^{\frac{\gamma+1}{2(\gamma-1)}}$$
where $A^*$ is the area of the duct corresponds to $M = 1$.
- Explain in brief as to why capillary tube is preferred to other throttling devices in household refrigerator.
- An oil engine operating on air-standard dual cycle has cylinder bore of $250\,\mathrm{mm}$ and stroke length of $300\,\mathrm{mm}$. The compression and expansion ratios are 10 and 6 respectively. The initial pressure and temperature of air before compression are $1.0$ bar and $27\,^\circ\mathrm{C}$ respectively. The heat added at constant pressure is twice the heat added at constant volume. Determine the pressure and temperature at all the salient points in the cycle, and the air-standard efficiency of the cycle. Also, calculate the clearance volume of the engine. Draw the $P$-$V$ diagram of the cycle. Take, for air, $\gamma = 1.4$ and $C_p = 1.005\,\mathrm{kJ/kg\text{-}K}$.
- A food storage chamber requires a refrigeration system of 12 TR capacity with an evaporator saturation temperature of $-8\,^\circ\mathrm{C}$ and condenser temperature of $30\,^\circ\mathrm{C}$. The refrigerant R-12 is sub-cooled by $5\,^\circ\mathrm{C}$ before entering the throttle valve, and the vapour is superheated inside the evaporator by $6\,^\circ\mathrm{C}$ before entering the compressor. If the liquid and vapour specific heats are $1.235\,\mathrm{kJ/kg\text{-}K}$ and $0.733\,\mathrm{kJ/kg\text{-}K}$ respectively, find the (i) refrigerating effect per kg, (ii) mass of refrigerant circulated per minute and (iii) COP. The relevant properties of the refrigerant R-12 are given below :
| Saturation temperature (°C) | Enthalpy (kJ/kg) Liquid | Enthalpy (kJ/kg) Vapour | Entropy (kJ/kg-K) Liquid | Entropy (kJ/kg-K) Vapour |
|---|---|---|---|---|
| -8 | 28.70 | 184.06 | 0.1148 | 0.7007 |
| 30 | 64.59 | 199.62 | 0.2400 | 0.6853 |
- Show, in the form of a table, how the following flow parameters change (increase/decrease/remain constant) in the rotor and stator blades of an axial flow compressor stage with 50% degree of reaction :
(i) Static temperature
(ii) Static pressure
(iii) Stagnation temperature
(iv) Stagnation pressure
(v) Relative velocity
(vi) Absolute velocity
Also, draw the corresponding $T$-$s$ diagram.
- $39.6\,\mathrm{m^3/min}$ of a mixture of recirculated room air and outdoor air enters a cooling coil at $31\,^\circ\mathrm{C}$ dry-bulb temperature and $18.5\,^\circ\mathrm{C}$ wet-bulb temperature. The apparatus dew-point temperature of the coil is $4.4\,^\circ\mathrm{C}$. The surface area of the coil is such that it would give $12.5\,\mathrm{kW}$ of refrigeration with the given entering air state. Determine the dry-bulb and wet-bulb temperatures of air leaving the coil, and the bypass factor. (Psychrometric Chart is given in Page No. 10)
- Obtain the following relationship between the characteristic Mach number ($M^*$) and actual Mach number ($M$) at a point in a flow field :
$$M^{*2} = \frac{(\gamma+1)M^2}{2+(\gamma-1)M^2}$$
A normal shock stands in a duct. The fluid is air, which can be considered as an ideal gas. Properties at upstream of the shock are $T_1 = 5\,^\circ\mathrm{C}$, $p_1 = 65\,\mathrm{kPa}$ and $V_1 = 668\,\mathrm{m/s}$. Determine the static temperature, static pressure and stagnation temperature downstream of the shock. For air, take $C_p = 1.005\,\mathrm{kJ/kg\text{-}K}$ and $\gamma = 1.4$.
- Explain why most of the medium-sized automobile engines are close to square shape with the cylinder bore diameter approximately equal to the stroke length.
- In a gas turbine plant, air at $1.0$ bar and $27\,^\circ\mathrm{C}$ is compressed to a pressure of $6.0$ bar in a compressor with isentropic efficiency of 85%. The air then passes through the combustion chamber where fuel is added. The hot gases expand in the turbine with an isentropic efficiency of 90%. The maximum temperature in the cycle is $1300\,^\circ\mathrm{C}$. The calorific value of the fuel is $44\,\mathrm{MJ/kg}$. If the net power output is $3.0\,\mathrm{MW}$, calculate the following :
(i) Cycle efficiency, (ii) Work ratio, (iii) Mass flow rate of air, (iv) Brake-specific fuel consumption (kg/kWh)
Consider the working fluid to have the properties of air throughout the cycle. Assume $\dot{m}_{air} \approx \dot{m}_{gases}$. Neglect all other losses. For air, $\gamma = 1.4$ and $C_p = 1.005\,\mathrm{kJ/kg\text{-}K}$. Also, draw the $T$-$s$ diagram of the cycle.
- A six-cylinder four-stroke SI engine is required to develop $190\,\mathrm{kW}$ of power running at $4500\,\mathrm{r.p.m.}$ The brake thermal efficiency is 32%. The air/fuel ratio is $12.5:1$ and the volumetric efficiency at this speed is 68%. If the stroke/bore ratio is $0.8$, determine the engine displacement required and the dimensions of bore and stroke. The calorific value of the fuel is $44200\,\mathrm{kJ/kg}$ and the free air conditions are $1.013$ bar and $15\,^\circ\mathrm{C}$. If the mechanical efficiency is 80%, calculate the brake-specific fuel consumption and the indicated thermal efficiency. $R_{air} = 0.287\,\mathrm{kJ/kg\text{-}K}$.
- What are the environmental and safety properties of an ideal refrigerant?