Mains PYQs
UPSC Mains Mechanical Engineering paper 1 2020 questions
- A car starts from rest with an acceleration of $6\,\mathrm{m/s^2}$ which decreases linearly with time to zero in 10 seconds after which the car continues at a constant speed. Determine the time required for the car to travel 400 m from start.
- A tower guy wire is anchored by means of a bolt at A. If the magnitude of the tension in the wire is 2500 N, determine the components of the force acting on the bolt in the x, y and z directions.
[Figure] Tower with top B on the y axis, height 80 m; A is the anchor point at 40 m (along the z direction) and 30 m (along the x direction) as marked.
- (i) A five-bar chain is shown in the figure. Prove that it is an unconstrained chain. [5]
[Figure] Five-bar chain with links numbered 1 to 5.
(ii) Show that the chain shown in the figure is not a kinematic chain. [5]
[Figure] Chain with joints A, B, C, D, E, F and links numbered 1 to 9 (1: AD, 2: AB, 3: BC, 4: CD, 5: CE, 6: BE, 7: EF, 8: BF, 9: AF).
- Define the term hardenability. Which factors affect hardenability?
- Determine the whirling speed of a shaft 25 mm diameter and 0.8 m long with a mass of 1 kg placed at mid span, simply supported at ends. The density of the shaft material is $50\,\mathrm{g/cm^3}$ and Young's modulus is $2\times10^6$ bar.
[Figure] Simply supported shaft of length 0.8 m with a 1 kg load at mid span.
- At a certain point in a piece of elastic material, there are normal tensile stresses of magnitude $120\,\mathrm{MN/m^2}$, $60\,\mathrm{MN/m^2}$ acting orthogonally to each other. In addition, there is a shearing stress of $80\,\mathrm{MN/m^2}$ acting normal to the normal stresses.
Determine:
(i) the magnitude and direction of the principal stresses
(ii) the magnitude and direction of the maximum shearing stress
(iii) the normal and shearing stress on a plane inclined at $30^\circ$ to the direction of $120\,\mathrm{MN/m^2}$ stress
[Figure] Stress element with $\sigma_x=120\,\mathrm{MN/m^2}$, $\sigma_y=60\,\mathrm{MN/m^2}$ and $\tau=80\,\mathrm{MN/m^2}$.
- (i) Determine the number of teeth and the speed of the pinion where the driven gear wheel has 60 teeth of 10 mm module and rotates at 300 rpm. The two spur gears have a velocity ratio of $\frac{1}{4}$. Also compute the pitch line velocity. [10]
(ii) Two parallel shafts, about 600 mm apart, are to be connected by spur gears. One shaft is to run at 360 rpm and the other at 120 rpm. Design the gears, if the circular pitch is to be 25 mm. [10]
- Determine the moment of inertia of the shaded area with respect to the x-axis.
[Figure] Rectangle 240 mm wide and 120 mm high with a semicircular cut-out of radius r = 90 mm at the top edge, centred on the top edge; x-axis along the bottom edge.
- Draw the shear force and bending moment diagrams for the beam and loading shown. Also determine the maximum values of shear force and bending moment along with their respective locations.
[Figure] Beam A-B-C-D-E with supports at A and D; loads 90 kN at B, 54 kN at C and 22 kN/m uniformly distributed over DE; AB = 1.8 m, BC = 2.4 m, CD = 3 m, DE = 2.4 m.
- The arms of a Porter governor are 300 mm long. The upper arms are pivoted on the axis of rotation. The lower arms are attached to a sleeve at a distance of 40 mm from the axis of rotation. The mass of the load on the sleeve is 70 kg and the mass of each ball is 10 kg. Determine the equilibrium speed when the radius of rotation of the balls is 200 mm. If the friction is equivalent to a load of 20 N at the sleeve, what will be the range of speed for this position?
- Draw the following crystallographic planes in cubic unit cell:
(i) $(101)$
(ii) $(1\bar{1}0)$
(iii) $(221)$
- A cylindrical shell 90 cm long, 20 cm internal diameter having thickness of metal as 8 mm is filled with fluid at atmospheric pressure. If an additional $20\,\mathrm{cm^3}$ of fluid is pumped into the cylinder, find
(i) the pressure exerted by the fluid on the cylinder.
(ii) the hoop stress induced.
Given:
Young's modulus $=2\times10^5\,\mathrm{N/mm^2}$
Poisson's ratio $=0.3$
- A rotor is completely balanced when masses of 2 kg and 1.2 kg are added temporarily in planes A and D each at 200 mm radius as shown in the figure. The balanced mass in the plane A is along the x-axis whereas in the plane D, it is at 120 mm radius. Determine the magnitudes and the directions of the masses B and C.
[Figure] Shaft with planes A, B, C, D; spacing A to B 350, B to C 500, C to D 250 (mm); angle 120 degrees marked at plane D.
- Classify the nano-materials depending on the number of dimensions in the nano range. What are the two basic approaches for processing of nano-structural materials?
- What do you understand by the term 'flash' in a forging? Explain with the help of a sketch.
- A hole and shaft have a basic size of 25 mm and are to have a clearance fit with maximum clearance of 0.02 mm and a minimum clearance of 0.01 mm. The hole tolerance is to be 1.5 times the shaft tolerance. Determine limits for both hole and shaft
(i) using a hole basis system.
(ii) using a shaft basis system.
- The life of a plain milling cutter of diameter 75 mm was found to decrease from 50 minutes to 30 minutes due to increase in speed of the cutter from 200 to 260 rpm while milling a cast iron plate at given feed and depth of cut. How much would be the life of that cutter if the speed is 120 rpm keeping other parameters unchanged?
- Enlist various types of plant layouts. Compare product layout and process layout.
- A company plans to sell an article at a local market. The articles are purchased at ₹ 5 on the condition that all unsold articles shall be returned. The rent of the space is ₹ 2,000. The articles will be sold at ₹ 9.
Determine the number of articles which must be sold
(i) To break-even.
(ii) To earn ₹ 400 as profit.
(iii) If the company sells 750 articles, calculate margin of safety and profit.
- During pure orthogonal turning of a metal rod by a tool of the following geometry it was noted that the magnitudes of the tangential component and the axial component of the cutting force are 600 N and 200 N respectively.
Inclination angle $=0^\circ$
Orthogonal rake $=0^\circ$
Principal cutting edge angle $=90^\circ$
Chip reduction coefficient $=1.732$
Using Merchant's circle diagram, determine the magnitudes of the shear force and the frictional force for the above condition.
- A component can be manufactured either on a centre lathe or on a turret lathe. The cost and time information to process a component is given below:
| Particulars | Centre lathe | Turret lathe |
|---|---|---|
| Set-up time | 30 minutes | 120 minutes |
| Processing time | 10 minutes | 5 minutes |
| Tooling-up cost (₹) | 200 | 500 |
| Labour cost/hr | ₹ 2 | ₹ 2 |
| Depreciation and other costs per hour | ₹ 10 | ₹ 20 |
The tooling-up cost is to be recovered within a year and there are no repeat orders. The requirements are to be met in two lots.
(i) Calculate the quantity at which both alternatives result in equal cost. (BEP)
(ii) Give the decision rule regarding the choice of lathes.
(iii) If the quantity required is 800 nos/year, which of the machines do you propose?
- Explain the process of metal transfer in gas metal arc welding process with neat sketches.
- The sales for a critical component manufactured by a company are given below. Forecast the demand for the components for the next three years using regression method:
| Years | Sales ('000) |
|---|---|
| 1986 | 30 |
| 1987 | 33 |
| 1988 | 37 |
| 1989 | 39 |
| 1990 | 42 |
| 1991 | 46 |
| 1992 | 48 |
| 1993 | 50 |
| 1994 | 55 |
| 1995 | 58 |
- A steel wire is drawn from an initial diameter of 12.7 mm to a final diameter of 10.2 mm at a speed of 90 m/min. The half-cone angle of the die is $6^\circ$ and the coefficient of friction at the job-die interface is 0.1. A tensile test on the original steel specimen gives a tensile yield stress of $207\,\mathrm{N/mm^2}$. A similar specimen shows a tensile yield stress of $414\,\mathrm{N/mm^2}$ at a strain of 0.5. Assuming a linear stress-strain relationship for the material, determine the drawing power and the maximum possible reduction with the same die. No back tension is applied.
- Enlist the basic elements of JIT and explain Kanban card in brief.
- The annual demand for a component is 2500 boxes. The company procures the item from a supplier at the rate of ₹ 750 per box. The company estimates the cost of carrying inventory to be 18% per unit per annum and the cost of ordering as ₹ 1,080 per order. The company works for 250 days in a year. How should the company design an inventory control system for this component? What will be the overall cost of the plan?
- Determine the percentage change in the machining time for a USM (Ultrasonic Machining) operation cutting WC plates when the tool material is changed from copper to stainless steel.
- What are the advantages and limitations of lean manufacturing? Discuss the difficulties in adopting lean technique.