Mains PYQs
UPSC Mains Mechanical Engineering paper 2 2019 questions
- Water is pumped from the basement tank of a multistorey building to the terrace tank by a 20 kW motor. The free surface of the terrace tank is 45 m higher than the basement tank. If the flow rate of water is $0.03\,\mathrm{m^3/s}$, determine the mechanical power that is converted to thermal energy during the process due to friction effect. Write the assumptions made in the calculation.
- Show that for a supersonic isentropic flow, an increase in flow area is accompanied by an increase in flow velocity and a decrease in pressure.
- An ideal simple gas turbine cycle is having a pressure ratio of $r$ and a temperature ratio, defined as the ratio of maximum temperature to minimum temperature in the cycle, of $t$, and the ratio of specific heats of $\gamma$. Show that the specific work output is maximum when the pressure ratio is such that the compressor outlet and turbine outlet temperatures are equal. Also, derive expressions for the two pressure ratios as functions of $t$ and $\gamma$, where the specific output becomes zero for a constant temperature ratio. Draw the $T$-$s$ diagram and a sketch of the layout of the components.
- A furnace wall consists of 200 mm inner layer of refractory brick ($k = 1.52\,\mathrm{W/m\text{-}K}$), 8 mm thick steel plate ($k = 45\,\mathrm{W/m\text{-}K}$) and outer layer of 100 mm thick insulation brick ($k = 0.138\,\mathrm{W/m\text{-}K}$). The inner wall of the furnace is maintained at $1150\,^\circ\mathrm{C}$, while the outer wall of the insulation brick is at $40\,^\circ\mathrm{C}$. Calculate the heat transfer through the wall. What is the temperature at the junction of steel plate and outer insulation brick wall?
- Liquid mercury flows at a rate of $1.25\,\mathrm{kg/s}$ through a copper tube of diameter 20 mm. Mercury enters the tube at $20\,^\circ\mathrm{C}$ and leaves the tube at $30\,^\circ\mathrm{C}$. Calculate the tube length for constant heat flux at the wall which is maintained at an average temperature of $40\,^\circ\mathrm{C}$. The empirical correlation for heat transfer for liquid metal flowing through a tube is given as $\overline{\mathrm{Nu}} = 7 + 0.025(\mathrm{Pe})^{0.8}$, where Pe is Peclet number, $\mathrm{Pe} = \mathrm{Pr}\cdot\mathrm{Re}$. The properties of mercury at $25\,^\circ\mathrm{C}$ are as follows :
$\rho = 13582\,\mathrm{kg/m^3}$
$C_P = 140\,\mathrm{J/kg\text{-}K}$
$k = 8.69\,\mathrm{W/m\text{-}K}$
$\nu = 1.5\times10^{-7}\,\mathrm{m^2/s}$
$\mathrm{Pr} = 0.0248$
- (i) A 40 litres electrical radiator (heater) containing heating oil is placed in a $50\,\mathrm{m^3}$ room. Both the room and the oil in the radiator are initially at $10\,^\circ\mathrm{C}$. The radiator with a rating of 2.4 kW is now turned on. At the same time, heat is lost from the room at an average rate of 0.35 kJ/s. After some time, the average temperature for air in the room is $20\,^\circ\mathrm{C}$ and the oil in the radiator is $50\,^\circ\mathrm{C}$. Take the density and the specific heat of the oil to be $950\,\mathrm{kg/m^3}$ and $2.2\,\mathrm{kJ/kg\text{-}K}$ respectively. Determine how long the heater is kept on. Assume the room is well-sealed and ambient pressure is 1 bar. [10]
(ii) Why are the temperature and pressure dependent properties in the saturated mixture region of pure substance? What is the difference between critical point and triple point? [10]
- A $45^\circ$ reducing pipe-bend in a horizontal plane, tapers from 600 mm diameter at inlet to 300 mm diameter at outlet. The gauge pressure at inlet is 140 kPa and the rate of flow of water through the bend is $0.425\,\mathrm{m^3/s}$. Neglecting friction, calculate the net resultant horizontal force exerted by the water on the bend.
- A 1 mm diameter electric wire is covered with 2 mm thick layer of insulation ($k = 0.5\,\mathrm{W/m\text{-}K}$). Air surrounding the wire is at $25\,^\circ\mathrm{C}$ and $h = 10\,\mathrm{W/m^2\text{-}K}$. The wire temperature is $100\,^\circ\mathrm{C}$. Find the rate of heat dissipation from the insulated wire per unit length. Also, find the maximum value of heat dissipation per unit length for the corresponding critical thickness of insulation.
- In an industrial gas turbine plant, the air leaving a single-sided centrifugal compressor enters the combustion chamber. The hot gases leaving the combustion chamber undergo expansion in a single-stage gas turbine. The compressor is required to deliver 14 kg of air per second, when operating at a (total to total) pressure ratio of 4 : 1 and a speed of 12000 r.p.m. The total head inlet conditions may be taken as $25\,^\circ\mathrm{C}$ and 1.0 bar. Assuming a slip factor of 0.9, a power input factor of 1.04 and an isentropic efficiency (based on total head) of 80%, estimate the overall diameter of the impeller. Assume no pre-whirl. If the Mach number at the impeller tip is not to exceed unity and 50% of the losses are assumed to occur in the impeller, find the minimum possible depth of the diffuser. Also, draw a sketch of the compressor, clearly showing the impeller and the diffuser. Draw the corresponding $T$-$s$ diagram also.
- A counterflow double-pipe heat exchanger is used to heat glycerin from $20\,^\circ\mathrm{C}$ to $50\,^\circ\mathrm{C}$ by hot water, which enters the thin-walled 2 cm diameter tubes at $80\,^\circ\mathrm{C}$ and leaves at $40\,^\circ\mathrm{C}$. The total length of the heat exchanger is 60 m. The convection heat transfer coefficient is $25\,\mathrm{W/m^2\text{-}K}$ on the glycerin side (in the annulus) and $160\,\mathrm{W/m^2\text{-}K}$ on the water side (in the inner tube). Determine the rate of heat transfer in the heat exchanger (i) before any fouling and (ii) after fouling with a fouling factor of $0.0006\,\mathrm{m^2\text{-}K/W}$ occurred on the glycerin side of the inner tube. The thermal resistance of the inner tube is negligible.
- A Carnot refrigeration cycle is operating between the minimum and maximum temperatures of $-8\,^\circ\mathrm{C}$ and $20\,^\circ\mathrm{C}$ respectively. The refrigerant used in the cycle is R-134a and the cycle is operating in the saturated liquid-vapour region. The mass of the refrigerant is 0.8 kg and the refrigerant is saturated liquid at the end of heat rejection process. The net work input to the cycle is 15 kJ. Determine the fraction of the mass of the refrigerant that vaporizes during the heat addition process. Given
$h_{fg}$ at $-8\,^\circ\mathrm{C} = 204.59\,\mathrm{kJ/kg}$
$h_{fg}$ at $20\,^\circ\mathrm{C} = 180.33\,\mathrm{kJ/kg}$
- With the help of continuity, momentum and energy equations, obtain an expression for Mach number after a normal shock in terms of the Mach number before the shock.
- Define degree of reaction for a stage of an axial flow compressor and derive an expression for the same in terms of the fluid angles and the blade angles. Show that when the degree of reaction is 50%, the velocity triangles are symmetrical. Consider a stage of an axial flow compressor with degree of reaction equal to 50% and isentropic efficiency (based on total head) is less than 100% in both the rotor and the stator blades. Draw the $T$-$s$ diagram and velocity triangles for this stage. Show in the form of a table, how the following flow parameters change in the rotor and the stator of the stage :
(i) Absolute velocity
(ii) Relative velocity
(iii) Stagnation pressure
(iv) Static pressure
(v) Stagnation temperature
(vi) Static temperature
- Daylight and incandescent light may be approximated as blackbody emissions at the effective surface temperatures of 5800 K and 2800 K, respectively. From the principles of radiation, show that incandescent lightbulbs are inefficient as light sources in the visible spectrum wavelength range of $0.40\,\mu\mathrm{m}$ to $0.76\,\mu\mathrm{m}$. The blackbody radiation function, $f_\lambda$ as a function of $\lambda T$ ($\mu$m-K) given in the table may be used. The blackbody radiation function, $f_\lambda$ represents the fraction of radiation emitted from a blackbody at temperature $T$ in the wavelength band from $\lambda = 0$ to $\lambda$, to the total radiation energy emitted by the blackbody in the wavelength range 0 to $\infty$.
Blackbody radiation function, $f_\lambda$
| $\lambda T$ ($\mu$m-K) | $f_\lambda$ | $\lambda T$ ($\mu$m-K) | $f_\lambda$ |
|---|---|---|---|
| 200 | 0.000000 | 6200 | 0.754140 |
| 400 | 0.000000 | 6400 | 0.769234 |
| 600 | 0.000000 | 6600 | 0.783199 |
| 800 | 0.000016 | 6800 | 0.796129 |
| 1000 | 0.000321 | 7000 | 0.808109 |
| 1200 | 0.002134 | 7200 | 0.819217 |
| 1400 | 0.007790 | 7400 | 0.829527 |
| 1600 | 0.019718 | 7600 | 0.839102 |
| 1800 | 0.039341 | 7800 | 0.848005 |
| 2000 | 0.066728 | 8000 | 0.856288 |
| 2200 | 0.100888 | 8500 | 0.874608 |
| 2400 | 0.140256 | 9000 | 0.890029 |
| 2600 | 0.183120 | 9500 | 0.903085 |
| 2800 | 0.227897 | 10000 | 0.914199 |
| 3000 | 0.273232 | 10500 | 0.923710 |
| 3200 | 0.318102 | 11000 | 0.931890 |
| 3400 | 0.361735 | 11500 | 0.939959 |
| 3600 | 0.403607 | 12000 | 0.945098 |
| 3800 | 0.443382 | 13000 | 0.955139 |
| 4000 | 0.480877 | 14000 | 0.962898 |
| 4200 | 0.516014 | 15000 | 0.969981 |
| 4400 | 0.548796 | 16000 | 0.973814 |
| 4600 | 0.579280 | 18000 | 0.980860 |
| 4800 | 0.607559 | 20000 | 0.985602 |
| 5000 | 0.633747 | 25000 | 0.992215 |
| 5200 | 0.658970 | 30000 | 0.995340 |
| 5400 | 0.680360 | 40000 | 0.997967 |
| 5600 | 0.701046 | 50000 | 0.998953 |
| 5800 | 0.720158 | 75000 | 0.999713 |
| 6000 | 0.737818 | 100000 | 0.999905 |
- What are the desired properties of lubricants used in IC engines? How do different additives help to achieve these desired properties? [6+4]
- Determine the height of a chimney to produce a static draught of 20 mm of water. The mean hot gas temperature in the chimney is $270\,^\circ\mathrm{C}$ and the atmospheric air temperature is $20\,^\circ\mathrm{C}$. Take atmospheric pressure as 0.101325 MPa. The characteristic gas constant for air is $287\,\mathrm{J/kg\text{-}K}$ and for chimney gas, it is $255\,\mathrm{J/kg\text{-}K}$.
- (i) Enumerate the desirable properties of refrigerant-absorbent pairs for vapour absorption refrigeration system. [5]
(ii) What are the drawbacks of presence of water vapour in the evaporator and condenser of an aqua-ammonia absorption refrigeration system? [5]
- Briefly explain different methods for the use of alcohols as alternate fuel in SI engines. Also, write the merits and demerits of alcohol as fuel.
- Atmospheric air at 1.033 bar and $35\,^\circ\mathrm{C}$ DBT and 60% RH is undergoing a psychrometric process. During the process, the specific humidity of air is reduced by 5 gm/kg of dry air and the DBT of air is reduced to $25\,^\circ\mathrm{C}$, while the pressure is maintained constant. Determine the relative humidity and dew-point temperature of air in the final condition. Solve the problem using only psychrometric relations.
Saturated Water-Temperature Table
| Temperature $T$ ($^\circ$C) | Saturated Pressure $P_{\mathrm{sat}}$ (kPa) |
|---|---|
| 0.01 | 0.6117 |
| 5 | 0.8725 |
| 10 | 1.2281 |
| 15 | 1.7057 |
| 20 | 2.3392 |
| 25 | 3.1698 |
| 30 | 4.2469 |
| 35 | 5.6291 |
| 40 | 7.3851 |
| 45 | 9.5953 |
- A Parson's turbine runs at 400 r.p.m. and it develops 75 kW of power per unit mass of steam flow per second. The exit angle of the blades is $20^\circ$ and the steam velocity is 1.4 times the blade velocity. Find the blade velocity and the inlet angle of the blades.
- A four-cylinder, four-stroke SI engine has an output of 80 kW at 3000 r.p.m. A Morse test is carried out and the brake torque readings are 175 N-m, 170 N-m, 174 N-m and 172 N-m, respectively. The specific fuel consumption for normal running at this engine speed is 0.385 kg/kWh. The calorific value of fuel is 44000 kJ/kg. Calculate the mechanical and brake thermal efficiencies of the engine.
- Explain how a simple capillary tube works as an expansion device in vapour compression refrigeration system. What are the advantages and disadvantages of capillary tube as an expansion device?
- A hall is to be maintained at $24\,^\circ\mathrm{C}$ DBT and 60% RH, when the following data are given :
Outdoor conditions : $38\,^\circ\mathrm{C}$ DBT and $28\,^\circ\mathrm{C}$ WBT
Sensible heat load in the room : 160000 kJ/hr
Latent heat load in the room : 40000 kJ/hr
Total infiltrated air : $1200\,\mathrm{m^3/hr}$
Apparatus dew-point temperature : $10\,^\circ\mathrm{C}$
The quantity of recirculated air from the hall is 60% of total. If the recirculated air is mixed with the conditioned air after the cooling coil, then find the following :
(i) The condition of air leaving the cooling coil and before mixing with the recirculated air
(ii) Condition of air before entering the hall
(iii) The mass of air entering the cooling coil
(iv) Bypass factor of the cooling coil
(v) The total mass of air supplied to the hall
(vi) The refrigeration load on the cooling coil in TR
Draw a sketch of the layout and show the process on a typical psychrometric plot. Use of psychrometirc chart data is permitted.
- (i) State the major advantages and disadvantages of combined gas and steam turbine power plants. [10]
(ii) Compare the thermal efficiencies of two boilers having the following data : [10]
Boiler 1 (Coal-fired) : Steam pressure-1.4 MPa; Steam produced/kg of coal fired-10 kg; Quality of steam-0.9; Feed water temperature-$27\,^\circ\mathrm{C}$; Calorific value of coal-34000 kJ/kg
Boiler 2 (Oil-fired) : Steam pressure-1.4 MPa; Steam produced/kg of oil fired-14 kg; Condition of steam (superheated)-$240\,^\circ\mathrm{C}$; Feed water temperature-$27\,^\circ\mathrm{C}$; Calorific value of oil-46000 kJ/kg
Use the following data :
At 1.4 MPa for steam-
$h_{\mathrm{superheated}} = 2903\,\mathrm{kJ/kg}$ at $240\,^\circ\mathrm{C}$
$h_f = 830\,\mathrm{kJ/kg}$
$h_{fg} = 1958\,\mathrm{kJ/kg}$
Specific heat of feed water = $4.1868\,\mathrm{kJ/kg\text{-}K}$
- (i) Explain knocking in SI engines with the help of a $p$-$\theta$ diagram. [6]
(ii) Discuss the effect of compression ratio and inlet gas temperature on knocking in SI engines. [4]
- A simple vapour compression refrigeration cycle using Freon 22 is designed for a load of 100 TR. The saturation temperatures in the evaporator and condenser are $5\,^\circ\mathrm{C}$ and $40\,^\circ\mathrm{C}$ respectively. The refrigerant leaves the evaporator and enters the compressor as saturated vapour. The refrigerant leaves the condenser and enters the expansion device as subcooled liquid with a subcooling of $5\,^\circ\mathrm{C}$. The specific heat of the vapour is 0.65 kJ/kg-K and the specific heat of the liquid is 1.1 kJ/kg-K for the refrigerant. Calculate (i) the mass flow rate (kg/s) of the refrigerant, (ii) the COP and isentropic compressor power and (iii) the heat rejected in the condenser. Use the following data :
| $T_{\mathrm{sat}}$ ($^\circ$C) | $P_{\mathrm{sat}}$ (bar) | $h_f$ (kJ/kg) | $h_g$ (kJ/kg) | $s_f$ (kJ/kg-K) | $s_g$ (kJ/kg-K) | $v_g$ ($\mathrm{m^3/kg}$) |
|---|---|---|---|---|---|---|
| 5 | 5.836 | 205.9 | 407.1 | 1.02115 | 1.7447 | 0.0404 |
| 40 | 15.331 | 249.53 | 416.4 | 1.16659 | 1.69953 | - |
- (i) Explain the variation of pressure along the axis of a convergent-divergent nozzle operating off the design pressure ratio. [10]
(ii) Discuss the principle of bypass governing in a steam turbine with neat sketches. [10]
- An engine working on ideal diesel cycle has a compression ratio of 15 : 1. The temperature of air at the beginning of the compression stroke is $27\,^\circ\mathrm{C}$ and the air-fuel ratio used is 35 : 1. Find the air-standard efficiency of the cycle. The calorific value of the fuel is 42000 kJ/kg.