Mains PYQs
UPSC Mains Mechanical Engineering paper 2 2018 questions
- The lighting needs of a classroom are met by 30 fluorescent lamps, each consuming 80 W of electricity. The lights in the classroom are kept on for 12 hours a day and 250 days during a year. For a unit electricity cost of ₹ 7 per kWh, determine the annual energy cost of lighting for this classroom.
- A plane wall of thickness 0.2 m and $k = 1.2$ W/m-K has a surface area of 15 m$^2$. The left and right sides of the wall are maintained at 120 °C and 50 °C respectively. Using the basic differential equation for heat conduction, determine the variation of temperature within the wall and the temperature at 0.13 m from the left. Also find the rate of conduction through the wall under steady-state conditions.
- A heat pump is to be used to heat a house during the winter as shown in Fig. 1. The house is to be maintained at 21 °C at all times. The house is estimated to be losing heat at a rate of 135000 kJ/hr when the outside temperature drops to $-5$ °C. Determine the maximum power required to drive this heat pump :
[Figure] Fig. 1: house at $T_H = 21$ °C losing 135000 kJ/hr; heat pump (HP) with $\dot{Q}_H$ to the house, $\dot{W}_{net,in} = ?$, and $\dot{Q}_L$ from cold outside air at $T_L = -5$ °C.
- Differentiate between physical delay and chemical delay with respect to ignition delay period. Also discuss the important engine parameters that affect the ignition delay period.
- Air at 20 °C and at atmospheric pressure flows at a velocity of 4.5 m/s past a flat plate with a sharp leading edge. The entire plate surface is maintained at a temperature of 60 °C. Assuming that the transition occurs at a critical Reynolds' number $5\times10^5$, find the distance from the leading edge at which the boundary layer changes from laminar to turbulent. At this location, also calculate (i) thicknesses of hydrodynamic and thermal boundary layers and (ii) local and average convective heat transfer coefficients. Assume cubic velocity profile and approximate method. At mean temperature of 40 °C, the properties of air are the following :
Density $= 1.128$ kg/m$^3$
Kinematic viscosity $= 16.96\times10^{-6}$ m$^2$/s
$k = 0.02755$ W/m-K
Pr $= 0.7$
- A rigid tank contains 10 kg of water at 90 °C. If 8 kg of water is in the liquid form and the rest is in the vapour form, determine (i) the pressure in the tank and (ii) the volume of the tank. Use the relevant data from the saturated water properties (Table 1) provided below for the calculations :
Table 1 : Saturated Water Properties
| Temp., T (°C) | Sat. press., Psat (kPa) | Specific volume vf (m3/kg) | Specific volume vg (m3/kg) | Internal energy uf (kJ/kg) | Internal energy ufg | Internal energy ug | Enthalpy hf (kJ/kg) | Enthalpy hfg | Enthalpy hg | Entropy sf (kJ/kg-K) | Entropy sfg | Entropy sg |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 75 | 38.597 | 0.001026 | 4.1291 | 313.99 | 2161.3 | 2475.3 | 314.03 | 2320.6 | 2634.6 | 1.0158 | 6.6655 | 7.6812 |
| 80 | 47.416 | 0.001029 | 3.4053 | 334.97 | 2146.6 | 2481.6 | 335.02 | 2308.0 | 2643.0 | 1.0756 | 6.5355 | 7.6111 |
| 85 | 57.868 | 0.001032 | 2.8261 | 355.96 | 2131.9 | 2487.8 | 356.02 | 2295.3 | 2651.4 | 1.1346 | 6.4089 | 7.5435 |
| 90 | 70.183 | 0.001036 | 2.3593 | 376.97 | 2117.0 | 2494.0 | 377.04 | 2282.5 | 2659.6 | 1.1929 | 6.2853 | 7.4782 |
| 95 | 84.609 | 0.001040 | 1.9808 | 398.00 | 2102.0 | 2500.1 | 398.09 | 2269.6 | 2667.6 | 1.2504 | 6.1647 | 7.4151 |
| 100 | 101.42 | 0.001043 | 1.6720 | 419.06 | 2087.0 | 2506.0 | 419.17 | 2256.4 | 2675.6 | 1.3072 | 6.0470 | 7.3542 |
- What is Reynolds-Colburn analogy? What do you mean by Colburn's $j$-factor?
- What are the different engine cooling systems? Also, mention the important functions performed by the lubrication systems of internal combustion engine.
- A heat engine working on ideal Otto cycle has a compression ratio 6. The temperature and pressure at the start of the compression stroke are 27 °C and 1 bar respectively. Heat addition in combustion stroke is 1170 kJ/kg. Find out the following parameters :
(i) Maximum temperature of the cycle
(ii) Maximum pressure of the cycle
(iii) Work output per kg of air
(iv) Air standard efficiency of the cycle
Assume the following values for air :
$C_v = 0.717$ kJ/kg-K and $\gamma = 1.4$
- A centrifugal compressor under test gave the following data :
Speed $= 11500$ r.p.m.
Inlet total head temperature $= 21$ °C
Outlet and inlet total head pressure $= 4$ bar, 1 bar
If the impeller diameter is 75 cm and slip factor is 0.92, what is the compressor efficiency?
- Heat is generated uniformly in uranium ($k = 29.5$ W/m-K) rods of 5 cm diameter at the rate of $7.5\times10^7$ W/m$^3$. Cooling water at 120 °C is circulated in the annulus around the rods with heat transfer coefficient of 55 kW/m$^2$-K. Find the maximum temperature of the fuel rods.
- Water ($C_p = 4.187$ kJ/kg-K) is heated at the rate of 1.4 kg/s from 40 °C to 70 °C by an oil ($C_p = 1.9$ kJ/kg-K) entering at 110 °C and leaving at 60 °C in a counterflow heat exchanger. If the overall heat transfer coefficient is 350 W/m$^2$-K, calculate the surface area required. Using the same entering fluid temperature and the same oil flow rate, calculate the exit temperature of oil. Also calculate the exit temperatures of oil and water and the rate of heat transfer, when the water flow rate is halved.
- An aircraft is flying at a cruising speed of 250 m/s at an altitude of 5000 m, where the atmospheric pressure is 54.05 kPa and the ambient air temperature is 255.7 K. The ambient air is first decelerated in a diffuser before it enters the compressor (see Fig. 2). Approximating both the diffuser and the compressor to be isentropic, determine the following :
(i) The stagnation pressure at the compressor inlet
(ii) The required compressor work per unit mass, if the stagnation pressure ratio of the compressor is 8
[Figure] Fig. 2: diffuser followed by compressor in an aircraft engine; inlet $T_1 = 255.7$ K, $P_1 = 54.05$ kPa, $V_1 = 250$ m/s; stagnation states $P_{01}, T_{01}$ after the diffuser and $P_{02}, T_{02}$ after the compressor.
- Liquid air boiling at $-153$ °C is stored in a spherical condenser of diameter 320 mm. The container is surrounded by a concentric spherical shell of diameter 360 mm in a room at 27 °C. The space between the two spheres is evacuated. The surfaces of the spheres are flushed with aluminium of emissivity 0.03. Taking the latent heat of vaporization of liquid air as 210 kJ/kg, find the rate of evaporation of liquid air.
- How are the ratings of the SI and CI engine fuels done? Explain in brief.
- Mention the desirable characteristics of the working fluid in a steam power plant.
- Explain briefly the different types of compressors used in refrigeration.
- Make a typical layout of steam power plant.
- What are human comfort and effective temperature? Sketch comfort zone on psychrometric chart.
- The data pertaining to an impulse turbine are as follows :
Blade speed $= 300$ m/s
Isentropic enthalpy drop in nozzles $= 450$ kJ/kg
Nozzle efficiency $= 0.9$
Nozzle angle $= 20^\circ$
Blade velocity coefficient $= 0.85$
Blade exit angle $= 25^\circ$
Sketch the velocity diagrams and calculate for a mass flow rate of 1 kg/s the following :
(i) The inlet angle of moving blade
(ii) The axial thrust
(iii) The driving force on the wheel
(iv) The diagram power
(v) The energy lost in the blades due to friction
- In a laboratory test, a psychrometer recorded dry-bulb temperature as 35 °C and wet-bulb temperature as 28 °C. Calculate (i) vapour pressure, (ii) relative humidity, (iii) specific humidity, (iv) vapour density in air, (v) dew point temperature and (vi) enthalpy of mixture. Barometric pressure is 1.01325 bar. Do not use psychrometric chart. Saturation pressures of water vapour at 35 °C and 28 °C are 0.05628 bar and 0.03782 bar respectively. Saturation temperature at partial pressure of water vapour is 25.6 °C.
- What is the difference between direct injection and indirect injection type combustion chambers of CI engines? Make labelled diagrams of any two types of combustion chambers used in CI engines.
- During an engine trial of a four-stroke diesel engine, the following observations were recorded :
No. of cylinders $= 4$
Diameter of piston $= 10$ cm
Stroke length $= 15$ cm
Indicated mean effective pressure $= 0.67$ MPa
Speed $= 2000$ r.p.m.
No. of explosions $= 980$ per minute
Brake torque $= 181.5$ N-m
Fuel consumption $= 11.89$ kg/hr
Calorific value of fuel $= 41800$ kJ/kg
Relative efficiency (on brake power basis) $= 0.5$
Quantity of jacket cooling water $= 1020$ kg/hr
Rise in temperature of cooling water $= 35$ °C
Specific heat of cooling water $= 4.18$ kJ/kg-K
Based on the above observations, find out the following engine parameters :
(i) Mechanical efficiency
(ii) Brake thermal efficiency
(iii) Air standard efficiency
(iv) Brake specific fuel consumption
(v) Percent heat loss to jacket cooling water
- (i) Discuss the effect of variation of back pressure on mass flow rate and pressure distribution in a convergent-divergent nozzle.
(ii) What do you mean by supersaturated flow of steam in nozzles?
- Draw a neat sketch of summer air-conditioning system and show the process on psychrometric chart.
- A Freon-12 refrigerator producing a cooling effect of 20 kJ/s operates on a simple cycle with pressure limits of 1.509 bar and 9.607 bar. The vapour leaves the evaporator dry saturated and there is no undercooling. Determine the power required by the machine. If the compressor operates at 300 r.p.m. and has a clearance volume of 3% of stroke volume, determine the piston displacement of the compressor. For compressor, assume that the expansion is following the law $PV^{1.13}$ = constant. Specific heat of vapour at condenser pressure is 0.747 kJ/kg-K :
Table : Properties of Refrigerant R-12
| Pressure (bar) | t (°C) | $v_g$ (m3/kg) | $h_f$ (kJ/kg) | $h_g$ (kJ/kg) | $s_g$ (kJ/kg-K) |
|---|---|---|---|---|---|
| 1.509 | -20 | 0.1088 | 54.23 | 178.61 | 0.7082 |
| 9.607 | 40 | - | 74.53 | 203.05 | 0.682 |
- Explain how the ideal regenerative cycle may approach to Carnot cycle efficiency. Also, mention the reason as why ideal regenerative cycle cannot be achieved in practice.
- Explain the working of practical NH$_3$-water vapour absorption refrigeration system with a diagram.