Mains PYQs
UPSC Mains Mechanical Engineering paper 1 2018 questions
- A cord ACB, 5 m long is attached at points A and B to the vertical walls, 3 m apart (Figure 1). A pulley of negligible radius carries a suspended load of 200 N and is free to roll without friction along the cord. Determine the position of equilibrium as defined by the distance X, that the pulley will assume and also the tensile force in the cord.
[Figure] Figure 1: walls 3 m apart; A on the left wall, B on the right wall 1 m above A's level (line AH-I); X measured from the left wall to the pulley C; tension T in both cord segments at angle $\theta$; load 200 N hangs from C.
- An element with stresses acting on it at a point is shown in Figure 2.
$\sigma_x = 80$ MPa
$\sigma_y = -100$ MPa
$\tau_{xy} = \pm 50$ MPa
[Figure] Figure 2: element with 80 and 100 normal stresses and 50 shear stresses marked; plane AB inclined at 20 degrees to the X-axis, its normal ($\sigma_\theta$) at 110 degrees w.r.t. X-axis. All stresses in MPa.
Determine :
(i) Normal and shear stresses acting on a plane AB, whose normal is at an angle of $110^\circ$ w.r.t. X-axis
(ii) Principal stresses and their location
(iii) Maximum shear stress and its location
- A shaft is rotating at 150 rpm and it transmits power of 300 kW. The diameter of the shaft is 100 mm. What is the magnitude of torsional shear stress and the twist if the maximum torque is 25% more than the mean torque ? The length of the shaft is 1.5 m. Given G = 85 GPa.
- A bare steel shaft of diameter D shows a first critical speed of 1200 rev/min. If the shaft was bored to make it hollow, with an inside diameter of 3/4 D, what would be the critical speed ?
- Draw a neatly labelled iron-iron carbide phase diagram indicating salient regions, phases and reactions.
- A block weighing 500 N just starts moving down a rough inclined plane when it is subjected to 200 N force acting up and parallel to the inclined plane and it is moving up the plane when pulled by a force of 300 N parallel to and up the plane. Find the inclination of the plane and the coefficient of friction between the inclined plane and the block.
- Two involute gears in a mesh have a module of 8 mm and pressure angle of $20^\circ$. The larger gear has 57 while the pinion has 23 teeth. If the addenda on pinion and gear wheels are equal to one module, find the following :
(i) Contact ratio (The number of pairs of teeth in contact)
(ii) Angle of action of the pinion and the gear wheel
(iii) Ratio of the sliding to rolling velocity at the
I. Beginning of contact
II. Pitch point
III. End of contact
- Summarize the microstructures and mechanical properties of the following microconstituents of iron-carbon alloys in terms of phases present, arrangement of phases and relative mechanical properties :
(i) Spheroidite
(ii) Fine pearlite
(iii) Bainite
(iv) Tempered martensite
(v) Martensite
- Determine the deflection at points C and D for the beam loaded as shown in Figure 3. The beam is of rectangular cross-section 150 mm $\times$ 300 mm (depth) and E = 200 GPa.
[Figure] Figure 3: beam with pin support at A and roller support at B; C is 2 m from A, B is 4 m from A (2 m beyond C), D is 1 m beyond B at the free end with a 100 kN downward load at D.
- What are cast irons ? On the basis of microstructure, briefly explain why gray iron is brittle and weak in tension. Compare gray and malleable cast irons with respect to the following :
(i) Composition and heat treatment
(ii) Microstructure
(iii) Mechanical characteristics
(iv) Applications
- The arms of a Hartnell governor are of equal length. When the sleeve is in the mid-position, the masses rotate in a circle with a diameter of 150 mm (the arms are vertical in the mid-position). Neglecting friction, the equilibrium speed for this position is 360 rpm. Maximum variation of speed, taking friction into account, is to be 6% of the mid-position speed for a maximum sleeve movement of 30 mm. The sleeve mass is 5 kg and the friction at the sleeve is 35 N.
Assume that the power of the governor is sufficient to overcome the friction by 1% change of speed on each side of the mid-position. While neglecting obliquity effect of arms, find the following :
(i) Mass of each rotating ball
(ii) Spring stiffness
(iii) Initial compression of the spring
- A thin cylindrical shell has an external diameter of 500 mm and wall thickness of 10 mm. The length of the cylinder is 1.7 m. Determine the increase in its internal diameter and also the increase in length when the inside pressure is 1 MPa. Given E = 210 GPa and Poisson's ratio = 0.3. Hence determine the change in volume of the cylinder if the ends are closed with flat plates.
- A pressure tank issues water at A with a horizontal velocity u as shown in Figure 4. For what range of values of u, will the water enter the opening BC ?
[Figure] Figure 4: tank on the left with outlet A at ground level; vertical wall 3 m from the tank; B is 1 m below A's level on the wall, opening BC is 1.5 m long below B (C below B).
- In a single-degree damped vibrating system, a suspended mass of 8 kg makes 30 oscillations in 18 seconds. The amplitude decreases to 0.25 of the initial value after 5 oscillations. Determine the following :
(i) Stiffness of the spring
(ii) Logarithmic decrement
(iii) Damping factor
(iv) Damping coefficient
- During an electric discharge drilling of a 10 mm square hole in a low carbon steel plate of 6 mm thickness, brass tool and kerosene are used. The resistance and capacitance in the relaxation circuit are 50 $\Omega$ and 10 $\mu$F, respectively. The supply voltage is 200 V and the gap is maintained at such a value that the discharge (sparking) takes place at 150 V. Estimate the time required to complete the drilling operation. Approximate relationship between material removal rate (Q) and power (W) for steel material is given by :
$Q \approx 27.4\,W^{1.54}$
- A company manufactures a single product having a marginal cost of ₹ 1.50 per unit. Fixed cost is ₹ 30,000 per annum. The market is such that up to 40,000 units can be sold at a price of ₹ 3.00 per unit, but any additional sale must be made at ₹ 2.00 per unit. Company has a planned profit of ₹ 50,000. How many units must be made and sold ?
- Explain the difference between NC and CNC machines mentioning the benefits of CNC machines over NC machines.
- The demand for a product during the last 10 years is given below. Estimate the demand for the 11th and 12th year by method of regression.
| Year | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 |
|---|---|---|---|---|---|---|---|---|---|---|
| Unit | 124 | 135 | 145 | 150 | 167 | 157 | 161 | 170 | 187 | 168 |
- (i) What is meant by "draft" in relation to rolling process ? Determine the maximum possible reduction for cold-rolling a 400 mm thick slab, when $\mu$ = 0.07 and the roll diameter is 700 mm. Briefly describe the methods of reducing the roll force by giving suitable explanation. [5]
(ii) What is the difference between open-die and impression-die forging ? What is barreling in relation to forging ? How can it be minimized ? How does barreling occur in upsetting of a hot work piece between cold dies and how can it be minimized ? Explain the role of flash in impression-die forging. [5]
- The table below gives the standard time for the sawing off operation of different jobs being processed at a job order production unit. Table also gives average monthly requirement of each indicated item.
| Part Name | Standard time per piece (min) | Average quantity per month |
|---|---|---|
| Control shaft | 8.46 | 1,250 |
| Serration shaft | 8.46 | 1,250 |
| Oil pump gear | 5.40 | 4,000 |
| Helical oil pump gear | 4.80 | 2,000 |
| Brake shaft | 5.40 | 1,000 |
| Hub | 9.60 | 2,500 |
| Hex nut | 17.16 | 250 |
| Thread rolls | 96.0 | 30 |
Assume equipment is running at 75% efficiency with capacity hours at 80% utilisation. Consider 400 hours is available per month per machine. If presently the production unit has 4 power saw machines, determine additional requirement of machines.
- What do you understand by Just-In-Time (JIT) ? What benefits can occur to the company from the application of JIT technique ?
- Melting efficiency in case of an arc welding of steel is given as 30%. The travel speed is 5 mm/sec and the cross-sectional area of the joint is 20 mm$^2$. Heat required to melt steel may be taken as 10 J/mm$^3$ and heat transfer efficiency as 85%. Find out the current drawn by the machine, if voltage potential is 20 V.
- Mild steel is being machined at a cutting speed of 200 m/min with a tool of rake angle of $10^\circ$. The width of cut and uncut thickness are 2 mm and 0.2 mm, respectively. The average value of the coefficient of friction between the tool and the chip is 0.5 and shear stress ($\tau_s$) of the work material is 400 N/mm$^2$. Using Merchant's first solution, determine :
(i) Shear angle
(ii) The cutting and thrust components of the machining force
- Explain the concept of clearance, interference and transition fit. How are fits represented in drawings ?
- A company has got a demand for a particular part at 10,000 units per year. The cost per unit is ₹ 2.00. It costs ₹ 36.00 to place an order and to process the delivery. The inventory carrying cost is estimated at 9% of average inventory investment.
Determine :
(i) Economic order quantity
(ii) Optimum number of orders to be placed per annum
(iii) Minimum total cost of inventory per annum
- Quality control department of a tire manufacturing plant has inspected the number of defective tires in twenty random samples with twenty observations each. Following are the number of defective tires found in each sample :
| Sample Number | Number of defective tires | Number of observations sampled | Fraction defectives |
|---|---|---|---|
| 1 | 3 | 20 | 0.15 |
| 2 | 2 | 20 | 0.10 |
| 3 | 1 | 20 | 0.05 |
| 4 | 2 | 20 | 0.10 |
| 5 | 1 | 20 | 0.05 |
| 6 | 3 | 20 | 0.15 |
| 7 | 3 | 20 | 0.15 |
| 8 | 2 | 20 | 0.10 |
| 9 | 1 | 20 | 0.05 |
| 10 | 2 | 20 | 0.10 |
| 11 | 3 | 20 | 0.15 |
| 12 | 2 | 20 | 0.10 |
| 13 | 2 | 20 | 0.10 |
| 14 | 1 | 20 | 0.05 |
| 15 | 1 | 20 | 0.05 |
| 16 | 2 | 20 | 0.10 |
| 17 | 4 | 20 | 0.20 |
| 18 | 3 | 20 | 0.15 |
| 19 | 1 | 20 | 0.05 |
| 20 | 1 | 20 | 0.05 |
Construct a P-chart 3 standard deviation [three sigma control chart (Z = 3)].
- Explain the term "Total Quality Management (TQM)".
- What do you mean by extrusion of metals ? What are some of the attractive features of this process ? What is the primary shape limitation of the extrusion process ? Differentiate between direct and indirect extrusion with the help of neatly labelled sketches. What is the primary benefit of indirect extrusion ? Briefly describe the three principal extrusion defects.