Mains PYQs
UPSC Mains Mechanical Engineering paper 1 2017 questions
- A beam $AB$ of length 2 m, hinged at $A$ and supported at $B$ by a cord which passes over two frictionless pulleys ($P$, $Q$), carries a 50 kN load as shown in Fig. 1(a). Determine the distance $x$, where 100 kN load is located on the beam, if the beam is to remain in equilibrium in horizontal position. Also determine the reaction at the hinged end.
[Figure] Fig. 1(a): beam $AB$ of length 2 m hinged at $A$, 100 kN load at distance $x$ from $A$, cord at $B$ over pulleys $P$ and $Q$ fixed to ceiling ($C$, $D$), tension $T$, 50 kN load hanging from pulley $Q$
- A state of plane stress is shown in Fig. 1(b).
Determine the following :
(i) Principal stresses
(ii) Principal planes
(iii) Maximum shear stress
[Figure] Fig. 1(b): element with 50 MPa on left and right faces, 10 MPa on top and bottom faces, shear stress 40 MPa
- A thin spherical vessel of 1000 mm diameter and 2 mm thickness is subjected to an internal pressure of 4 MPa. The Young's modulus and Poisson's ratio are 200 GPa and 0.3 respectively. Find the following :
(i) Hoop stress
(ii) Change in volume of the vessel
- A steam engine develops 300 kW power at 9.5 rad/s. The coefficient of fluctuation of energy is found to be 0.1 and fluctuation of speed is kept within $\pm$0.5% of mean speed. Find the mass of the flywheel required if the radius of gyration is 2 m.
- A machine of mass 8 kg is supported on springs having combined stiffness of 5.4 N/mm. A dashpot is attached to the system that exerts a force of 40 N, when the mass has a velocity of 1 m/s. Determine the following :
(i) Critical damping coefficient
(ii) Damping factor
(iii) Logarithmic decrement
(iv) Ratio of two consecutive amplitudes
- A simply supported beam of rectangular section is 200 mm wide and 300 mm deep. It supports a uniformly distributed load of 6 kN/m over an effective span of 4 m as shown in Fig. 2 (a). Calculate the magnitude and direction of the principal stresses at a point located at 0.50 m from the left support and 50 mm above the neutral axis.
[Figure] Fig. 2(a): simply supported beam $AB$ of span 4 m with UDL 6 kN/m
- Compare the permissible diameter of a steel circular shaft, subjected to torsion, according to the following theories of failure. Assume Poisson's ratio to be 0.3 :
(i) Maximum stress theory
(ii) Maximum shear stress theory
(iii) Maximum strain theory
- Fig. 2(c) shows three flat blocks positioned on the 30$^\circ$ incline. A force $P$ parallel to the incline is applied to the middle block. The movement of the upper block is prevented by attaching to a fixed support by a wire. The coefficient of static friction for each of the three pairs of mating surfaces is shown in the figure. Determine the maximum value which $P$ may have before any slipping takes place.
[Figure] Fig. 2(c): blocks of 25 kg (top), 45 kg (middle), 35 kg (bottom) on a 30$^\circ$ incline; $\mu_s$ = 0.25 between 25 kg and 45 kg, $\mu_s$ = 0.35 between 45 kg and 35 kg, $\mu_s$ = 0.40 between 35 kg and incline; force $P$ on the middle block
- A solid aluminium shaft 1 m long and 50 mm diameter is to be replaced by a tubular steel shaft of the length and the same outside diameter (i.e., 50 mm) such that each of the two shafts could have the same angle of twist per unit torsional moment over the total length. What must the inner diameter of the tubular steel shaft be? The modulus of rigidity of steel is three times that of aluminium.
- A compound epicyclic gear is shown in Fig. 3(b). Gears $A$, $D$ and $E$ are free to rotate on axis $P$. Compound gears $B$ and $C$ rotate together on axis $Q$ at the end of arm $F$. All the gears have equal pitch. The number of external teeth on gears $A$, $B$ and $C$ are 18, 45 and 21 respectively. Gears $D$ and $E$ are annular gears. Gear $A$ rotates at 100 r.p.m. in counter-clockwise direction and gear $D$ rotates at 450 r.p.m. clockwise. Find the speed and direction of arm $F$ and gear $E$.
[Figure] Fig. 3(b): compound epicyclic gear train with gears $A$, $B$, $C$, $D$, $E$, axes $P$, $Q$ and arm $F$
- For a eutectoid steel, draw and label continuous cooling transformation (CCT) diagram. Explain normalizing and hardening heat treatment with regard to phase transformation using relevant cooling curves on CCT diagram.
- Four masses $A$, $B$, $C$ and $D$ are attached to a shaft and revolve in the same plane. The masses are 12 kg, 10 kg, 18 kg and 15 kg respectively and their radii of rotation are 40 mm, 50 mm, 60 mm and 30 mm respectively. The angular positions of masses $B$, $C$ and $D$ are 60$^\circ$, 135$^\circ$ and 270$^\circ$ from the mass $A$. Find the magnitude and position of balancing mass at a radius of 100 mm.
- Draw the stress-strain diagram for mild steel and describe the salient points of the curve.
- A Porter governor having all arms of 240 mm length is pivoted on the axis of rotation. Each ball has a mass of 5 kg and the load on the sleeve is 18 kg. The ball path is 150 mm when the sleeve begins to rise and 200 mm at the maximum speed. Find the following :
(i) Range of speed
(ii) Coefficient of sensitiveness, if the friction at the sleeve is equivalent to a force of 10 N
- Electrochemical machining of 400 mm$^2$ surface of iron is performed using supply voltage of 15 V and tool-workpiece gap of 0.3 mm. Considering gap resistance for the flow of current through electrolyte to be 0.0015 $\Omega$, calculate the metal removal rate, MRR (m$^3$/s).
The relevant data for iron are the following :
Valency = 2
Atomic weight = 55.85
Density = 7860 kg/m$^3$
Faraday's constant = 96540 coulombs
- An annealed copper plate of 300 mm width and 20 mm thickness is rolled to 16 mm thickness in one pass. Considering radius of the roller as 400 mm, rotational speed of 80 r.p.m. and average flow stress during rolling as 400 MPa, calculate the true strain and rolling force (kN).
- The machining of steel is carried out using two types of cutting tool, i.e., tool $A$ and tool $B$. Data/technical parameters related with tools are given below in the table. Which tool will you prefer for 200 minutes of tool life and why?
| Tool | Value of $n$ for tool life equation | Cutting speed for one minute tool life (m/min) |
|---|---|---|
| Tool $A$ | 0.25 | 150 |
| Tool $B$ | 0.30 | 180 |
- Describe the philosophy of lean management including waste and value stream with regard to manufacturing.
- The demand for an item is 500 units and 600 units for July and August respectively. Considering forecast for July as 300 units, determine the forecast for September using exponential smoothing method. Assume value of $\alpha$ as 0.3.
- For orthogonal turning using a cutting tool having a rake angle of 5$^\circ$, the following data is given :
Chip-thickness ratio = 0.5
Rake angle = 5$^\circ$
Main cutting force = 1600 N
Thrust force = 1300 N
Calculate the shear plane angle, friction force (N), normal force (N) and coefficient of friction at chip-tool interface.
- Two aluminium plates are welded using tungsten inert gas (TIG) welding process with the help of welding current 150 A, arc voltage 12 V and arc travel speed 2 mm/s. Considering heat transfer efficiency of TIG welding process as 90% and heat required for melting unit volume of metal (Al) as 15 J/mm$^3$, calculate the melting efficiency of the process if the cross-sectional area of the weld joint is 20 mm$^2$.
- Explain the principle of abrasive waterjet machining using suitable schematic. Write the advantages and applications of abrasive waterjet machining.
- The following limits are specified to give a clearance fit between a shaft and a hole in a limit system :
Shaft = $30^{-0.08}_{-0.021}$ mm $\phi$
Hole = $30^{+0.023}_{-0.000}$ mm $\phi$
Calculate the following :
(i) Basic size
(ii) Shaft and hole tolerances
(iii) Shaft and hole limits
(iv) Maximum and minimum clearances
- Lathe machine operations take 40 min to produce a product. If the efficiency of the lathe machine is 80% and rejection is 20%, then determine the number of lathe machines required for producing 800 pieces per week. Assume 52 weeks per year and 48 hours per week as working hours available.
- A manufacturing company is producing an item for which the following information is given :
Selling price per unit = ₹ 20
Variable cost per unit = ₹ 10
Fixed cost = ₹ 2,00,000
However due to changing market condition, variable cost increased by 20% and fixed cost increased by 10%. If the breakeven quantity is maintained, then what will be the revised selling price?
- Monthly consumption of an item is 350 units and price per unit is ₹ 15. Inventory carrying cost is 20 percent and ordering cost is ₹ 40 per order; lead time of 1 month's stock. Assuming ROL system, calculate the following :
(i) Reorder quantity
(ii) Reordering level
(iii) Minimum level
(iv) Maximum level
(v) Average inventory
- A car manufacturer performs final inspection before shipping to the dealers. The final inspection involves testing and inspection of car with regard to number of parameters. There is a possibility that a car may fail to satisfy various parameters (which can be termed as defects). Periodically ten (10) cars were taken randomly for testing and inspection. Data obtained after inspection and testing of each car with regard to number of defects is given below. Determine the control limits for C chart and comment :
| Sample/Car | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 |
|---|---|---|---|---|---|---|---|---|---|---|
| No. of defects | 10 | 12 | 13 | 08 | 09 | 10 | 12 | 20 | 07 | 06 |
- Describe different types of control systems possible for CNC operations along with respective applications using suitable schematic.