Mains PYQs
UPSC Mains Mechanical Engineering paper 2 2016 questions
- Which is the more effective way to increase the efficiency of a Carnot engine-to increase $T_1$ keeping $T_2$ constant or to decrease $T_2$ keeping $T_1$ constant?
- What is the pressure coefficient of a centrifugal compressor? Derive that $\psi_p = 1 - \phi_2 \cot\beta_2$, where $\phi_2$ = flow coefficient.
- Define effectiveness, NTU and heat capacity ratio in case of heat exchanger analysis, and also establish a relationship among them for counterflow heat exchanger.
- Derive Wien's displacement law from Planck's law of radiation.
- What are the supercharging limits of SI and CI engines? What are the modifications recommended for supercharging an IC engine?
- A cylindrical rod of length $L$ insulated on its lateral surface is initially in contact at one end with a wall at temperature $T_1$ and at the other end with a wall at lower temperature $T_2$. The temperature within the rod initially varies linearly with position $x$ according to $T(x) = T_1 - \frac{T_1 - T_2}{L}x$. The rod is insulated on its ends and eventually comes to a final equilibrium state where the temperature is $T_f$. Evaluate $T_f$ in terms of $T_1$ and $T_2$, and show that the amount of entropy generated is
$$S_{\mathrm{gen}} = mc\left[1 + \ln T_f + \frac{T_2}{T_1 - T_2}\ln T_2 - \frac{T_1}{T_1 - T_2}\ln T_1\right]$$
where $c$ is the specific heat of the rod.
- Air flows over a surface, 2 m in length, oriented in the direction of flow and of sufficient breadth, maintained at 150 $^\circ$C. The pressure is 1 atm and the bulk air temperature is 30 $^\circ$C. If the air velocity is 12 m/s, find the average heat transfer coefficient.
[ Use the following physical properties of air at film temperature, that is $(150 + 30)/2 = 90\,^\circ$C :
$\rho = 0.962\,\mathrm{kg/m^3}$, $\mu = 2.131 \times 10^{-5}\,\mathrm{kg/m\,s}$
$k = 0.031\,\mathrm{W/m\,K}$, $C_p = 1.01\,\mathrm{kJ/kg\,K}$
$\mathrm{Nu} = 0.332\,\mathrm{Re}^{1/2}\,\mathrm{Pr}^{1/3}$ for laminar flow
$\mathrm{Nu} = 0.0296\,\mathrm{Re}^{0.8}\,\mathrm{Pr}^{1/3}$ for turbulent flow ]
- Briefly describe the effect of volatility on the following performance characteristics of SI engine :
(i) Cold starting
(ii) Hot starting
(iii) Vapour lock
(iv) Evaporation loss
- A steam pipe (inner diameter = 150 mm and outer diameter = 160 mm) having thermal conductivity 58 W/m K is covered with two layers of insulation of thicknesses 30 mm and 50 mm respectively and thermal conductivities 0.18 W/m K and 0.09 W/m K respectively. The temperature of inner surface of the steam pipe is 320 $^\circ$C and that of the outer surface of the insulation layers is 40 $^\circ$C.
(i) Determine the quantity of heat lost per metre length of the steam pipe and layer contact temperature.
(ii) If the condition of the steam is dry and saturated, find the quality of the steam coming out of one metre pipe assuming that the quantity of steam flowing is 0.32 kg/min.
[ Use the data : At 320 $^\circ$C saturation temperature
$h_f = 1463$ kJ/kg, $h_{fg} = 1240$ kJ/kg, $h_g = 2703$ kJ/kg ]
- An engine having a single-jet carburettor consumes 6.0 kg/h of fuel. The density of fuel is 750 $\mathrm{kg/m^3}$. The level in the float chamber is 3 mm below the top of the jet when the engine is not running. The ambient conditions are :
Pressure = 1.013 bar and Temperature = 21 $^\circ$C
The jet diameter is 1.2 mm and its discharge coefficient is 0.65. The discharge coefficient of air is 0.80. The air/fuel ratio is 15.3 : 1. Determine-
(i) critical air velocity;
(ii) depression at the throat in mm of $\mathrm{H_2O}$ ;
(iii) effective throat diameter.
Neglect the compressibility of air.
- Explain the phenomenon of surging and choking in a centrifugal compressor.
- What is a current meter? Where is it used? Explain with the help of a neat sketch the functioning of a current meter.
- In a double-sided centrifugal compressor, the following data are given :
Overall diameter of impeller = 50 cm
Eye tip diameter = 30 cm
Eye root diameter = 15 cm
RPM = 15000
Total mass flow = 18 kg/s
Inlet total head temperature = 295 K
Total head isentropic efficiency = 78%
Power input factor = 1.04
Slip factor = 0.9
Assume that the velocity of air at inlet is 150 m/s and is axial, and remains constant across the eye annulus.
Find (i) the total head pressure ratio, (ii) the power required to drive the compressor and (iii) the inlet angles of the vanes at the root and tip of impeller eye. Draw the $T$-$s$ diagram and velocity triangles.
- In a large steam power plant, a shell and tube type condenser is used which has the following data :
Heat exchange data = 2100 MW
Number of shell passes = 1
Number of tubes = 31500
Number of tube passes = 2
Diameter of each tube = 25 mm
Condensation temperature = 50 $^\circ$C
Mass flow rate of cooling water = $3.4 \times 10^4$ kg/s
Heat transfer coefficient on the steam side = 11400 $\mathrm{W/m^2\,K}$
Inlet water temperature = 20 $^\circ$C
Heat transfer coefficient on the water side = 8018 $\mathrm{W/m^2\,K}$
Using only $\varepsilon$-NTU method, calculate-
(i) the outlet temperature of cooling water;
(ii) the length of tube pass.
[ Properties of water at 27 $^\circ$C are :
$C_p = 4.18$ kJ/kg K, $\mu = 855 \times 10^{-6}\,\mathrm{N\,s/m^2}$, $k = 0.613$ W/m K
and Pr = 5.83 ]
Neglect the thermal resistance due to tube wall.
- What do you mean by boundary layer separation? Briefly explain the various methods of controlling of boundary layer separation.
- What is the function of an economiser in a thermal power plant? Why are the economiser tubes often provided with fins on the gas side? Explain.
- What are the desirable properties of a fluid for use as a working substance in Rankine cycle based heat engine plant? Discuss with the help of $T$-$s$ diagram.
- Discuss any four thermodynamic desirable properties of an ideal refrigerant.
- What is an adiabatic saturation process? Why does the enthalpy of an air-vapour mixture remain constant during this process?
- Explain what you mean by Fanno flow. Clearly mention the assumptions made and governing equations involved in the Fanno flow.
- A convergent-divergent nozzle receives steam at 5.0 bar, 200 $^\circ$C and expands isentropically into a space at 2.0 bar. Neglecting the inlet velocity, calculate the exit area required for a mass flow of 0.3 kg/s in the following cases :
(i) When the flow is in equilibrium throughout
(ii) When the flow is supersaturated with $PV^{1.3}$ = constant
Calculate also for this supersaturated flow, the degree of supercooling and the degree of supersaturation.
Properties of steam :
At 5.0 bar and 200 $^\circ$C, $h = 2855.4$ kJ/kg, $s = 7.0592$ kJ/kg K,
$v = 0.4249\,\mathrm{m^3/kg}$
At 2.0 bar and $T_{\mathrm{sat}} = 120.23\,^\circ$C, $h_f = 504.7$ kJ/kg, $h_g = 2706.7$ kJ/kg,
$s_f = 1.5301$ kJ/kg K, $s_g = 7.1271$ kJ/kg K, $v_f = 0.001061\,\mathrm{m^3/kg}$,
$v_g = 0.8857\,\mathrm{m^3/kg}$
- Explain, with the help of neat sketches, vapour absorption cycle for refrigeration and also derive an expression to calculate ideal COP of it.
- Write a note on the off-design performance characteristics of a convergent-divergent nozzle. Plot the pressure distribution along the axis of the nozzle for different back pressures.
- A vapour compression refrigeration cycle works between pressure limits 10 bar and 3 bar. The working fluid is dry at the end of compression and there is no undercooling before the expansion valve. If refrigerant flow rate is 10 kg/min, determine-
(i) the COP;
(ii) the capacity of the refrigerator.
Table for properties of the refrigerant is as under :
| Pressure (bar) | Saturation temperature ($^\circ$C) | Liquid heat (kJ/kg) | Latent heat (kJ/kg) | Liquid entropy (kJ/kg K) | Vapour entropy (kJ/kg K) |
| --- | --- | --- | --- | --- | --- |
| 10 | 25 | 298.9 | 1166.94 | 1.1242 | 5.0391 |
| 3 | -10 | 135.37 | 1297.68 | 0.5443 | 5.4770 |
- What is the function of a governor in a steam turbine? With the help of a neat sketch, explain the working of throttle governing. Show the process on $h$-$s$ diagram.
- Air at dry-bulb temperature of 30 $^\circ$C and 60% relative humidity enters a cooling coil at the rate of 250 $\mathrm{m^3/min}$.
(i) Determine the refrigeration in ton needed to bring the temperature of the air to the coil temperature of 23 $^\circ$C and also the relative humidity at that condition.
(ii) If the effective surface temperature of the cooling coil or ADP is 12 $^\circ$C and the by-pass factor is 0.1, determine the refrigeration in ton needed and the mass of water condensed out at the cooling coil per minute. Determine also the sensible heat factor for the process through the coil.
- Define distorted model. Explain why models of rivers and harbours are made as distorted models. Write down the merits and demerits of distorted models.
- A cyclic steam power plant is to be designed for a steam temperature at turbine inlet of 360 $^\circ$C and an exhaust pressure of 0.08 bar. After isentropic expansion of steam in the turbine, the moisture content at the turbine exhaust is not to exceed 15%. Determine the greatest allowable steam pressure at the turbine inlet, and calculate the Rankine cycle efficiency for these steam conditions. Estimate also the mean temperature of heat addition. Compare the Rankine cycle efficiency with the Carnot cycle efficiency operating between the mean temperature of heat addition and the condenser temperature. Neglect the pump work input.
Properties of steam :
At $P = 0.08$ bar and $T_{\mathrm{sat}} = 41\,^\circ$C, $h_f = 173.88$ kJ/kg,
$s_f = 0.5926$ kJ/kg K, $h_{fg} = 2403.1$ kJ/kg, $s_{fg} = 7.6361$ kJ/kg K