Mains PYQs
UPSC Mains Electrical Engineering paper 1 2025 questions
- In the circuit given below, find the voltages at point A and point B.
[Figure] Circuit with nodes A, B and ground G: 12 Ω and 6 Ω in series from A to B with a 3 A current source across the 6 Ω (and the 12 Ω/6 Ω junction); 9 Ω between A-side and B-side of an inner triangle; 3 Ω and 4 Ω from the 9 Ω ends to the centre node connected to G; 6 V source and 6 Ω from A to G; 4 Ω and 12 V source from B to G.
- Determine the time domain signal $x(t)$ corresponding to the DTFT given below :
[Figure] Plots of $|X(e^{j\Omega})|$ and $\arg[X(e^{j\Omega})]$ against $\Omega$. The magnitude is $\sin(\Omega)$-shaped rectified lobes with a peak of 1, over $-\pi/2 \le \Omega \le \pi/2$, repeating with period $2\pi$ (lobes between $-5\pi/2$ and $-3\pi/2$, $-\pi/2$ and $\pi/2$, $3\pi/2$ and $5\pi/2$). The phase is a straight line through the origin rising to $2\pi$ at the lobe edge, periodic in $\Omega$.
- Draw the output voltage waveform of the circuit given below for 5 V, 50 Hz ac rms input. Forward voltage drop in diode $D_1$ is 0.6 V.
[Figure] Input through capacitor $C_1$ = 100 $\mu$F in series; $R_1$ = 10 K across the output; diode $D_1$ in series with a 3 V battery across the output.
- Design a sequential circuit with two D flip flops A and B and one input X. Let the state of the circuit remain the same for X = 0. However, when X = 1, the circuit goes through the state transitions from 00 to 10 to 11 to 01, back to 00 and then repeats.
- Calculate Z-parameters for the two-port network given in the circuit diagram.
[Figure] Two-port with 3 Ω resistor in the top series arm between the ports, two 3 Ω resistors in series in a parallel upper branch, and a 3 Ω resistor from their junction to the common bottom line; $V_1$, $I_1$ at port 1 and $V_2$, $I_2$ at port 2.
- In the circuit shown in the diagram, initially key $K_1$ is closed and capacitor has no charge (at time t = 0).
Now at time t = 10 seconds, key $K_1$ is opened and at t = 18.68 seconds it is again closed.
Plot output voltage across the capacitor with respect to time and find output voltage values at time 10 seconds, 18.68 seconds and 28.68 seconds.
[Figure] 95 Ω resistor in series with a 5 V source to terminal B; capacitor C = 0.1 F from B to A (output); 1 A current source, 0.1 A current source and 5 Ω resistor with switch $K_1$ in the left section.
- Consider the circuit of an operational amplifier given here in which Zener diodes $Z_1$ and $Z_2$ are having reverse breakdown voltage = 7.4 V and forward voltage drop = 0.6 V.
(i) Draw the output voltage waveform showing voltage value with time and calculate frequency of output waveform. [10]
(ii) Modify the circuit for duty cycle factor D = 0.25 by replacing $R_1$ from combination of suitable resistances and diodes, so that output frequency is not changed. [10]
[Figure] Op-amp with supply +12 V and -12 V; $R_1$ = 100 K from output node $V_3$ to the inverting input $V_1$; $C_1$ = 0.1 $\mu$F from $V_1$ to ground; $R_2$ = 1 K from op-amp output to $V_3$; $R_3$ = 39 K and $R_4$ = 1 K divider from $V_3$ to ground with midpoint $V_2$ to the non-inverting input; back-to-back Zeners $Z_1$, $Z_2$ across the output.
- Determine the causal signal $x[n]$ if its z-transform $X(z)$ is specified by a pole-zero pattern shown in the figure below. Take the constant $G = \frac{1}{4}$.
[Figure] Pole-zero plot: zeroes at $-\frac{1}{2}$ and $-\frac{1}{4}$ on the real axis; poles at $\frac{1}{2}$ on the real axis and a complex conjugate pair at radius $r = \frac{1}{\sqrt{2}}$ and angle $\pm\frac{\pi}{4}$ (real part $\frac{1}{4}$... as drawn, at $\frac{1}{4}$ on the Re axis marker).
- Consider the Boolean function :
$F(A, B, C, D) = \sum m (1, 3, 4, 11, 12, 13, 14, 15)$
Implement it with a 4-to-1 multiplexer and external gates. Connect inputs A and B to the selection lines. Input to the four data lines is a function of the variables C and D which are obtained by expressing F as a function of C and D for each of the four cases when AB = 00, 01, 10 and 11. Functions are to be implemented with external gates.
- In the circuit given below, transistors $T_1$ and $T_2$ are having $V_{BE}$ = 0.6 V and $\beta$ = 499.
(i) Calculate small signal ac voltage gain of the amplifier at 20 Hz and 2 kHz.
(ii) Find dc voltages on collectors of transistors $T_1$ and $T_2$ respectively.
[Figure] Two-stage BJT amplifier: $V_{CC}$ = 12 V; $R_1$ = 9.1 K, $R_2$ = 2 K, $R_3$ = 36 K, $R_4$ = 100 K, $R_5$ = 200 E, $R_6$ = 1.3 K, $R_7$ = 1 K, $R_L$ = 10 K; $C_1$ = 10 $\mu$F, $C_2$ = 10 $\mu$F, $C_3$ = 100 $\mu$F, $C_4$ = 3.3 $\mu$F, $C_5$ = 100 $\mu$F.
- Impulse response of an LTI system, h(n) is defined in the interval $N_0 \le n \le N_1$. If the input x(n) to the LTI system is zero except in the interval $N_2 \le n \le N_3$, find the interval for which the output y(n) exists in forms of $N_0$, $N_1$, $N_2$ and $N_3$.
- For the Schottky transistor circuit shown below, determine $I_B$, $I_D$, $I_C$ and $V_{CE}$. Next, remove the Schottky diode and determine $I_B$, $I_D$, $I_C$ and $V_{CE}$ assuming additional values of $V_{BE}$ (sat.) = 0.8 V and $V_{CE}$ (sat.) = 0.1 V. Assume parameter values of $\beta$ = 50, $V_{BE}$ (on) = 0.7 V and $V_f$ = 0.3 V for the Schottky diode.
[Figure] NPN transistor with Schottky diode between base and collector; $R_S$ = 10 kΩ and $V_{BB}$ = 5.8 V at the base; $R_C$ = 1 kΩ and $V_{CC}$ = 5 V at the collector; $I_B$, $I_D$, $I_C$ marked.
- Find the Fourier transform of the following signals :
(i) $x(t) = \left[\frac{2\sin(3\pi t)}{\pi t}\right] \cdot \left[\frac{\sin(2\pi t)}{\pi t}\right]$
(ii) $x(t) = \int_{-\infty}^{t} \frac{\sin(2\pi t)}{\pi t}\, dt$
Specify the properties used.
- In the circuit shown below, $V_s$ is the ac voltage source given by $V_s = V_o \cos \omega t$, with $V_o$ = 14.14 V and $\omega$ = 300 rad/sec.
Calculate the value of load resistance $R_L$ for maximum power transfer and also find out maximum power transferred to load.
k = 1 n = 0.2 (Turns Ratio)
[Figure] Source $V_s$ with $R_1$ = 40 ohms in series with the primary of a transformer; secondary connected to load $R_L$.
- As shown in the figure, just inside the surface of a dielectric slab, the electric field ($E_1$) is 15 V/m and it makes an angle of $30^\circ$ with the surface. The electric field ($E_2$) makes $65.5^\circ$ angle with the surface, just above the surface. Determine the magnitude of $E_2$ and the dielectric constant of the slab.
[Figure] Interface between regions (1) below and (2) above; $E_1$ at $30^\circ$ to the surface in region 1; $E_2$ at $65.5^\circ$ to the surface in region 2, with components $E_{t2}$ and $E_{n2}$.
- Show with the help of suitable derivations that the voltage regulation of a transformer varies with the power factor of the load. At what power factor will the voltage regulation be :
(i) zero, and
(ii) maximum ?
- A single-phase Thyristor converter circuit as shown in the figure is feeding to a constant current load of 10 A. The supply voltage is of 230 V, 50 Hz and source inductance of 2 mH. Assume the Thyristors are ideal and triggering angle $\alpha = 30^\circ$. Calculate (i) the overlap angle u, and (ii) the drop in output voltage.
[Figure] Single-phase fully controlled thyristor bridge fed from source $v_s$ through source inductance $L_s$ (current $i_s$), with a 10 A constant current load.
- Show that for a binomial random variable, the mean is given by np and the variance is given by np (1 – p), where n gives the number of trials and p gives the probability of successes.
- The frequency range of operation of a superheterodyne FM receiver is 88 MHz – 108 MHz. The centre frequency of the IF amplifier ($f_{IF}$) and the frequency of the local oscillator ($f_{LO}$) are so chosen that $f_{IF} < f_{LO}$. The design has to be so carried out that the image frequency $f_c'$ falls outside of the 88 MHz – 108 MHz region. Determine the minimum required value of $f_{IF}$ and the corresponding range of variations in $f_{LO}$ for that chosen value of $f_{IF}$.
- (i) What is meant by armature reaction in DC machines ? Show with the help of developed view of armature conductors and poles that the effect of armature m.m.f. on the main field is entirely cross-magnetizing. [10]
(ii) A 10 kW, 220 V DC shunt motor draws a line current of 5 A while running at no-load speed of 1200 rpm. It has an armature resistance of 0.2 $\Omega$ and field resistance of 200 $\Omega$. Determine the efficiency of the motor when it delivers rated load. [10]
- A converter circuit as shown in the figure is being used to charge a battery of voltage E = 24 V. The average charging current $I_{dc}$ = 6 A, and supply voltage $V_s$ = 60 V, 50 Hz. Determine
(i) the value of limiting resistor 'R', and
(ii) input power factor.
[Figure] AC source in series with a diode, resistor R and battery E = 24 V.
- A DSB-SC amplitude-modulated signal with power spectral density as shown in figure (a) is corrupted with additive noise that has a power spectral density $\left(\frac{N_0}{2}\right)$ within the passband region of the signal. The received signal-plus-noise is demodulated and low pass filtered as shown in figure (b). Determine the SNR at the output of the LPF.
[BW : bandwidth]
[Figure] (a) $S_u(f)$ with level $P_0$ and triangular bands around $\pm f_c$ spanning $f_c - W$ to $f_c + W$; (b) $|H(f)|$ = 1 for $-W \le f \le W$; r(t) multiplied by $\cos(2\pi f_c t)$ then LPF with BW = W giving the output.
[Given : carrier signal = $\cos(2\pi f_c t)$]
- It is given that $\vec{E} = E_m \sin(\omega t - \alpha z)\, \hat{a}_y$ in free space $\alpha > 0$.
(i) Determine $\vec{D}$, $\vec{B}$ and $\vec{H}$. Plot $\vec{E}$ and $\vec{H}$ at t = 0. State clearly if any assumption is made. [10]
(ii) Show that these $\vec{E}$ and $\vec{H}$ fields constitute a wave travelling in the z-direction. Also demonstrate that the wave speed and E/H depend solely on the properties of free space. [10]
Given : $\mu_0 = 4\pi \times 10^{-7}$ H/m, and $\varepsilon_0 = \frac{1}{36\pi} \times 10^{-9}$ F/m.
- (i) A 3-phase, 4-pole, 400 V, 10 kW, 50 Hz slip ring induction motor develops rated output at rated voltage and frequency with its slip ring short-circuited. The maximum torque equal to twice the full load torque, occurs at a slip of 12.5% with zero external resistance in rotor circuit. Neglect stator impedance, stator core and mechanical losses. Determine :
I. slip and motor speed at full load torque, and
II. starting current in terms of full load current. [10]
(ii) An industry has an average electrical load of 600 kW at a p.f. of 0.6 lagging. A synchronous motor with an efficiency of 90% is used to raise the combined p.f. to 0.9 lagging and at the same time supply a mechanical load of 100 kW. Calculate kVA capacity of the synchronous motor and synchronous motor operating power factor. [10]
- The buck-boost converter has an input voltage of $V_s$ = 12 V. The duty cycle D = 0.25 and the switching frequency is 20 kHz. The inductance L = 150 $\mu$H and filter capacitor C = 250 $\mu$F. The average load current $I_o$ = 1.25 A. Determine :
(i) the peak-to-peak ripple in the inductor current, and
(ii) the critical values of inductor L and capacitor C for CCM.
- (i) Show that the Smith chart constructed for a lossless transmission line gives a family of r-circles, having a radius of $\frac{1}{(1+r)}$ for each circle which is centred at $\Gamma_r = \frac{r}{(1+r)}$ and $\Gamma_i = 0$. Here, r = normalized resistance of the load impedance, $\Gamma_r$ and $\Gamma_i$ = real and imaginary parts of voltage reflection coefficient of the load impedance, respectively. [10]
(ii) In the figure given below, determine the amplitudes of the reflected and transmitted $\vec{E}$ and $\vec{H}$ at the interface, if $E_0^i$ = 1.2 $\times$ $10^{-3}$ V/m in region 1, where $\varepsilon_{r_1}$ = 7.5, $\mu_{r_1}$ = 1 and $\sigma_1$ = 0. Given : Region 2 is a free space and assume normal incidence. Also, $\mu_0 = 4\pi \times 10^{-7}$ H/m and $\varepsilon_0 = \frac{1}{36\pi} \times 10^{-9}$ F/m. [10]
[Figure] Interface between region 1 ($\varepsilon_{r_1}$, $\mu_{r_1}$) and region 2 ($\varepsilon_0$, $\mu_0$) with incident $E_0^i$ and reflected $E_0^r$ on the left, transmitted $E_0^t$ on the right, and directions $\psi^i$, $\psi^r$, $\psi^t$.
- A sinusoidal modulating signal m(t) of frequency $f_m$ produces an AM signal : $u(t) = A_c\,[1 + \beta \cos(2\pi f_m t)] \cos(2\pi f_c t)$, where $f_c$ is carrier frequency. Here, $f_c \gg f_m$ and $\beta$ = 2. This u(t) is applied to an ideal envelope detector which produces an output x(t).
(i) Determine the Fourier series representation of x(t).
(ii) Also determine the ratio of second harmonic amplitude to fundamental amplitude in x(t).
- Discuss in brief various methods of voltage control within 3-phase inverters.