Mains PYQs
UPSC Mains Electrical Engineering paper 1 2024 questions
- Find the voltage on points $A$ and $B$ of the given circuit :
[Figure]
Circuit: 10 V source, 2 $\Omega$ resistor to node $A$, 1 $\Omega$ resistor and 2 A current source in series from $A$, 2 $\Omega$ resistor from $A$ to ground, 5 V source, then 2 $\Omega$ and 3 $\Omega$ resistors in series with terminal $B$ at their junction.
- Determine the Z-transform of $x[n] = n\left(\frac{1}{2}\right)^{n+2} u[n+2]$. Specify the properties used.
- In the circuit diagram given here, $T_1$ and $T_2$ are transistors with matched characteristics. The transistor parameters in active region are $\beta = 200$ and $V_{BE} = 688\,\mathrm{mV}$. Find $V_{CE}$ of transistor $T_2$ :
[Figure]
+12 V supply, 560 $\Omega$ resistor to $T_1$ collector, 470 $\Omega$ resistor to $T_2$ collector, current mirror arrangement with bases joined.
- A Binary Coded Decimal (BCD) code is to be transmitted to a remote receiver. Bits are arranged as $A_3\ A_2\ A_1\ A_0$. Design a circuit at the receiving end which has an error detector to check the legal BCD code and produce a HIGH for any error condition.
- In the circuit given here, $D_1$ is an ideal diode and key $K_1$ is ON for a long period of time. Now at time $t_0$, key $K_1$ is opened. Draw the voltage waveform on capacitor $C_1$ and find the final steady-state voltage on the capacitor :
[Figure]
9 V source, $L = 10\,\mathrm{mH}$, diode $D_1$, key $K_1$ (open at $t_0$), $R_1 = 0.9\,\Omega$, $C_1 = 100\,\mu\mathrm{F}$.
- Draw the circuit diagram, function table, logic symbol and switch model for a CMOS gate (using six transistors) with two inputs $A$ and $B$ and an output $Z$, such that
$Z = 0$ if $A = 1$ and $B = 0$, and $Z = 1$ otherwise
- For the signals $f_1(t)$ and $f_2(t)$ shown in the figures below, find and sketch $\int_{-\infty}^{t} f(x)\,dx$ :
[Figure]
$f_1(t)$: a rectangular pulse, positive from $t<0$ to 1, negative from 1 to 3, with an impulse of strength (+1) at $t = 3$. $f_2(t)$: constant 1 for $t \ge 0$ with impulses of strength (-1) at three points.
- Determine the time signal that corresponds to the following bilateral Laplace transform and the ROCs given below by using the method of partial fractions :
$$X(s) = \frac{4s^2 + 8s + 10}{(s+2)(s^2 + 2s + 5)}$$
(i) With ROC $\mathrm{Re}(s) < -2$
(ii) With ROC $\mathrm{Re}(s) > -1$
(iii) With ROC $-2 < \mathrm{Re}(s) < -1$
- Explain the working of the given OPAMP circuit. Draw the output waveforms at points $A$ and $B$ showing the time and voltage.
Given that, $V_{Z_1} = V_{Z_2} = 3.3\,\mathrm{V}$, $C_1 = 1\,\mu\mathrm{F}$, the power supply voltage to OPAMPs is $\pm 12\,\mathrm{V}$ and $R_1 = R_2 = R_3 = R_4 = R_5 = R_6 = 2\,\mathrm{k}\Omega$ :
[Figure]
Suggest to replace suitable resistances so that the output voltages at $A$ and $B$ are having swing of $\pm 6\,\mathrm{V}$ and the output frequency is fixed to 500 Hz.
- Find the logic equations for the outputs in the concise form and write the corresponding truth table for the circuit given below :
[Figure]
Inputs $D_0$, $D_1$; outputs $\overline{Y_0}$, $\overline{Y_1}$, $\overline{Y_2}$, $\overline{Y_3}$ from a network of NAND gates.
- In the circuit diagram given here, load resistance $R_L$ is to be set for maximum power transfer. Draw Thevenin equivalent circuit across $ab$ and calculate the value of $R_L$ for maximum power transfer. Also calculate the power loss in resistance $R_3$, when the circuit is delivering maximum power to load $R_L$ :
[Figure]
9 V source, $R_1 = 12\,\Omega$, dependent source $2V_{ab}$, $R_2 = 12\,\Omega$ with 3 V source, $R_3 = 4\,\Omega$, terminals $a$-$b$ with voltage $V_{ab}$ across variable $R_L$.
- (i) Define input bias current and input offset voltage for an OPAMP. Using an OPAMP, draw an inverting amplifier circuit with gain = -4 in such a way that the effect of bias current is minimized. [10]
(ii) In the linear regulated power supply circuit shown here, calculate the output voltage adjustment range and maximum power dissipation in transistor $T_1$ in worst case :
[Figure]
Input 15 V to 20 V DC, 1 k$\Omega$ with 12 V zener, potentiometer network 1 k$\Omega$, 10 k$\Omega$, 1 k$\Omega$, OPAMP $I_1$, 470 $\Omega$, transistors $T_1$ and $T_2$, 0.7 $\Omega$ sense resistor, Output.
($T_1$ and $T_2$ are Si transistors) [10]
- A circuit using three 2-input multiplexers is shown below. Determine the function performed by this circuit :
[Figure]
Inputs $I_3, I_2, I_1, I_0$, selects $S_1$, $S_0$; two first-stage MUXes give $Z_2$ and $Z_1$, a second-stage MUX gives $Z$.
- A uniform plane wave travels in vacuum along $+y$ direction. The electric field of the wave at some instant is given as $\vec{E} = 4\hat{x} + 3\hat{z}$. Find the vector magnetic field $\vec{H}$. (Given, $\mu_0 = 4\pi \times 10^{-7}\,\mathrm{H/m}$, $\varepsilon_0 = \frac{1}{36\pi} \times 10^{-9}\,\mathrm{F/m}$)
- The maximum efficiency of a 200 kVA, 3300/600 V, 50 Hz, single-phase transformer is 98% and occurs at 75% full load and unity power factor. If the leakage impedance is 10%, find the voltage regulation at full load and power factor 0.8 lagging.
- A diode circuit with an $L$-$C$ load is shown in the figure, with the capacitor having an initial voltage $V_C(t=0) = 120\,\mathrm{V}$, capacitance $C = 12\,\mu\mathrm{F}$ and inductance $L = 48\,\mu\mathrm{H}$. If switch $S$ is closed at $t = 0$ s, then find the following :
(i) Peak value of current $i$
(ii) Conduction time of the diode
[Figure]
Series loop of switch $S$ (closing at $t=0$), inductor $L$, capacitor $C$ with $V_C(t=0)$ and a diode.
- How can linear pre-emphasis and de-emphasis filters be employed to improve the performance of an FM system? Is the improvement in output SNR dependent on both the frequency responses of the pre-emphasis filter and the de-emphasis filter?
- A transmission line is 25 m long. It has characteristic impedance $Z_0 = 40\,\Omega$ and operates at 2 MHz. The line is terminated with a load of $Z_L = (50 + j30)\,\Omega$. If the wave velocity is $u = 0.8c$ (with $c = 3 \times 10^8\,\mathrm{m/s}$) on the line, determine (i) the reflection coefficient and (ii) the input impedance.
- (i) An AM signal $s(t) = A_c[1 + k_a m(t)]\cos(2\pi f_c t)$ is applied to the system shown in the figure. Show that the message signal $m(t)$ can be obtained from the square-rooter output $v_3(t)$ :
[Figure]
Block diagram: $s(t)$ into Squarer ($v_1(t) = s^2(t)$), then Low-pass filter ($v_2(t)$), then Square rooter ($v_3(t) = \sqrt{v_2(t)}$).
Assume that $|k_a m(t)| < 1$ for all $t$, the message signal $m(t)$ is limited to the interval $-\omega \le f \le \omega$, and the carrier frequency $f_c > 2\omega$. [10]
(ii) A narrow band FM signal is approximately given as
$$s(t) \approx A_c\cos(2\pi f_c t) - \beta A_c \sin(2\pi f_c t)\sin(2\pi f_m t)$$
Determine the envelope of this modulated signal. Also determine the ratio of the maximum to the minimum value of this envelope. Plot this ratio versus $\beta$, with $\beta$ restricted to the interval $0 \le \beta \le 0.4$.
Also determine the average power of the narrow band FM signal, expressed as a percentage of the average power of the unmodulated carrier wave. [10]
- (i) Explain why PWM inverters are preferred over square wave inverters. Further, draw the harmonic spectrum to highlight the differences in unipolar and bipolar PWM techniques. [10]
(ii) A single-phase, full-bridge inverter has DC-link voltage $V_{DC} = 400\,\mathrm{V}$, and the fundamental frequency of 50 Hz. Find the r.m.s. value of the voltages of the fundamental and next two prominent harmonics for the following cases :
(1) Square wave mode
(2) Voltage cancellation mode with $\alpha = 20^\circ$ [10]
- A 50 hp, 440 V, 50 Hz, star-connected, three-phase induction motor has a starting torque of 75% and maximum torque of 250% of the full-load torque. Find the following :
(i) Slip at which maximum torque occurs
(ii) Slip at full-load torque
- (i) Draw the neat and properly labelled output voltage waveform of a three-phase, phase-controlled rectifier having firing angle $\alpha$. Also derive the relationship for average output voltage in terms of line voltage $V_{LL}$ and firing angle $\alpha$. [10]
(ii) A three-phase full-wave controlled rectifier is being operated from a star-connected, 415 V, 50 Hz supply. This rectifier is feeding a constant current load of 15 kW. It is required to obtain an average output voltage of 80% of maximum possible output voltage. Find the firing angle, r.m.s. value of line current and input power factor. Assume devices are ideal. [10]
- (i) Show that the maximum power that a synchronous generator can supply when connected to constant voltage, constant frequency busbars increases with the excitation. [10]
(ii) An 11 kV, 3-phase, star-connected turbo-alternator delivers 250 A at unity power factor when running on constant voltage and frequency busbars. If the excitation is increased so that the delivered current rises to 300 A, find the power factor at which now machine works and percentage increase in the induced e.m.f., assuming a constant steam supply and unchanged efficiency. The armature resistance is $0.5\,\Omega$ per phase and the synchronous reactance is $10\,\Omega$ per phase. [10]
- A medium has infinite conductivity for $z \le 0$, $\varepsilon_r = 7$ and $\mu_r = 18$, and $\sigma = 0$ for $z > 0$. The electric field for $z > 0$ is given as $\vec{E} = 10\cos(3 \times 10^8 t - 15x)\,\hat{z}$, as shown below. Determine the surface charge density and surface current density at location $(3, 4, 0)$ at $t = 0.8\,\mathrm{ns}$. Given, $\mu_0 = 4\pi \times 10^{-7}\,\mathrm{H/m}$, $\varepsilon_0 = \frac{1}{36\pi} \times 10^{-9}\,\mathrm{F/m}$ :
[Figure]
Arrows of $\vec{E}$ along $z$ above the plane $z = 0$.
- In the figure given below, region 1 is the side of the plane $y + z = 1$ containing the origin and in this region, $\mu_{r_1} = 5$. In region 2, $\mu_{r_2} = 7$. It is given that $\vec{B}_1 = 3.0\,\vec{a}_x + 1.0\,\vec{a}_y$ (T). Determine $\vec{B}_2$ and $\vec{H}_2$. Given, $\mu_0 = 4\pi \times 10^{-7}\,\mathrm{H/m}$ :
[Figure]
Axes $y$, $z$ with origin $O$; the plane $y + z = 1$ separates region 1 ($\mu_{r_1} = 5$, containing $O$) from region 2 ($\mu_{r_2} = 7$).
- The message signal $m(t)$ has a bandwidth of 20 kHz, a power of 20 W and a maximum amplitude of 8. It is desired to transmit this message through a channel to the destination with 80 dB attenuation and additive white noise with power spectral density $S_n(f) = \frac{N_0}{2} = 0.5 \times 10^{-12}\,\mathrm{W/Hz}$ and achieve an SNR at the modulator output of at least 50 dB. What is the required transmitter power and channel bandwidth, if the modulation scheme employed is as under?
(i) DSB-SC AM
(ii) SSB AM
(iii) Conventional DSB AM with modulation index 0.6
- An ideal DC-DC converter as shown in the figure has an input voltage of $V_s = 20\,\mathrm{V}$, the duty ratio $D = 0.25$ and the switching frequency is 20 kHz. The inductance $L = 150\,\mu\mathrm{H}$ and capacitance $C = 240\,\mu\mathrm{F}$. The average diode current is 1.2 A. Determine the following :
(i) Peak-peak ripple current of the inductor
(ii) Peak current through the switch $S$
[Figure]
Switch $S$ in series, inductor $L$ shunt, diode in series, then capacitor $C$ and load $V_o$ in parallel (boost converter).