Mains PYQs
UPSC Mains Electrical Engineering paper 2 2023 questions
- The figure shows a unity feedback system. The steady-state value of the unit step response $c(t)$ is 0.8. Determine the maximum overshoot in the response $c(t)$ :
[Figure] Unity negative feedback loop with input $u(t)$, forward block $\frac{K}{(s+1)(s+2)}$ and output $c(t)$.
- A circuit breaker is rated as 2500 A, 1500 MVA, 33 kV, 3 sec, 3-phase, oil circuit breaker. Determine its rated normal current, breaking current, making current and short-time rating (current).
- An audio signal, whose bandwidth is 15 kHz, is to be digitized using PCM. Uniform quantization with 1024 levels and binary encoding are assumed. Determine the minimum sampling rate. If the actual sampling rate is 20% excess of the minimum rate, determine the minimum permissible bit rate.
- Briefly explain the following logical instructions of 8085 microprocessor :
(i) ANA M
(ii) XRA M
(iii) CMC
(iv) STC
(v) RRC
- In a three-phase 400 km long transmission line, the conductors are spaced at the corners of an equilateral triangle of side 5 m. The diameter of each conductor is 3 cm. Calculate the capacitance per phase of the 400 km long conductor.
- The block diagram of a feedback system is shown in the figure.
(i) Sketch the complete root locus of the system.
(ii) What is the value of $K$ at $s = 0$?
(iii) Find the range of $K$ for closed-loop stability.
[Figure] Negative feedback loop with input $R(s)$, forward block $\frac{K}{(s-1)(s^2+4s+7)}$, output $C(s)$, and feedback block $s+4$.
- Draw the connection diagram of a Schering bridge to measure the capacitance and dissipation factor. Write the balance equations and derive the formulae for finding the capacitance and dissipation factor.
- A linear delta modulator is designed to transmit speech signal bandlimited to 4 kHz. The specifications are-
sampling rate = 10 times Nyquist rate
step size = 100 mV
The system is tested with 1 kHz sinusoidal signal. Determine the maximum amplitude of the test signal so that slope overload does not occur. Calculate the maximum power that can be transmitted without slope overload.
- Write the state and output equations for the system shown in the figure. Choose state variables $x_1$ and $x_2$ as shown in the figure. Check the controllability and observability of the system :
[Figure] Block diagram: input $u$ minus feedback (from $x_2$ block) enters block $\frac{-5}{s+4}$ with output $x_1$; $u$-minus-feedback signal also goes through a gain block 1; the outputs of $\frac{-5}{s+4}$ and of the gain 1 are summed to give $y$; $y$ is fed back through block $\frac{1}{s-1}$ whose output $x_2$ is subtracted at the input summing junction.
- (i) Differentiate between full decoding and partial decoding techniques used by 8085 microprocessor to decode an address. Give advantages and disadvantages of each technique. [10]
(ii) Discuss with example how BCD number addition is performed using DAA instruction of 8085 microprocessor. [10]
- A 6600 V, 50 Hz, single-core, lead-sheathed cable has the following data :
Conductor diameter = 1.6 cm
Length = 5 km
Internal diameter of the sheath = 3.2 cm
Resistivity of insulation = $1.5\times10^{12}\,\Omega$-m
Relative permittivity of insulation = 3.8
Calculate the insulation resistance, capacitance and the maximum electric stress in the insulation.
- Consider a systematic linear block code with binary elements whose parity check equations are
$p_1 = m_1 + m_2 + m_3$
$p_2 = m_2 + m_3 + m_4$
$p_3 = m_1 + m_3 + m_4$
$p_4 = m_1 + m_2 + m_4$
where $m_i$ are message digits and $p_i$ are parity check digits.
(i) Find the generator matrix and parity check matrix for the code.
(ii) How many errors can this code detect? How many errors can be corrected?
(iii) If 10100100 is the received code word, find the corresponding transmitted code word assuming that single-bit error has been made during transmission.
- A transmission line has the following parameters :
$A = D = 1\angle 5^\circ$, $B = 88\angle 75^\circ$
(i) Determine the sending-end voltage and the voltage regulation if the line supplies a load of 40 MW at 0.8 p.f. lagging with receiving-end voltage 132 kV.
(ii) Find the power and power factor of the load if the voltages at the two ends are 132 kV and with a phase difference of $30^\circ$.
- Explain four instructions which are used to control interrupt structure of 8085 microprocessor.
- The figure shows a compensator network, where $R_1 = 3\,\mathrm{M\Omega}$, $R_2 = 1\,\mathrm{M\Omega}$, $C = 1\,\mu\mathrm{F}$. $V_i(t)$ and $V_o(t)$ are the input voltage and output voltage respectively. Determine the attenuation in dB provided by this network at very high frequencies :
[Figure] $R_1$ in the series arm; a shunt branch of $C$ in series with $R_2$ across the output; input $V_i(t)$ at left, output $V_o(t)$ at right.
- A resistive strain gauge, with a gauge factor 2.2, is cemented on a rectangular steel bar with the elastic modulus, $E = 205\times10^6\,\mathrm{kN/m^2}$. The width and thickness of the steel bar is 3.5 cm and 0.55 cm respectively. An axial force of 12 kN is applied. If the nominal resistance of the strain gauge is $100\,\Omega$, determine the change in resistance of the strain gauge.
- A three-phase, 50 Hz, 415 V supply delivers 250 kW power at power factor of 0.8 lagging. The line power factor is desired to be improved to 0.9 lagging by installing shunt capacitors. Calculate the capacitance if they are connected in delta.
- Binary data is transmitted over additive white Gaussian noise (AWGN) channel at a bit rate of 5 kilobits/sec. The single-sided power spectral density for the channel is $10^{-7}\,\mathrm{W/Hz}$. Non-coherent orthogonal binary FSK with higher frequency signalling tone of 1 MHz is used. The bit energy, $E_b = 2\times10^{-6}\,\mathrm{J}$. Determine the minimum required bandwidth and average bit error probability.
- Consider a three-phase, $\Delta$-Y connected, 30 MVA, 33/11 kV transformer with differential relay protection. If the CT ratios are 500 : 5 A on the primary side and 2000 : 5 A on the secondary side, compute the relay current setting for faults drawing up to 200% of rated transformer current.
- (i) A power system has two generators with the following cost curves :
Generator 1 : $C_1(P_{g1}) = 0.008\,P_{g1}^2 + 8\,P_{g1} + 380$ (thousand rupees/hour)
Generator 2 : $C_2(P_{g2}) = 0.009\,P_{g2}^2 + 7\,P_{g2} + 430$ (thousand rupees/hour)
The generator limits are
$120\,\mathrm{MW} \le P_{g1} \le 680\,\mathrm{MW}$
$60\,\mathrm{MW} \le P_{g2} \le 550\,\mathrm{MW}$
A load demand of 650 MW is supplied by the generators in an optimal manner. Determine the optimal generation of each generator, neglecting losses in the transmission network. [10]
(ii) A three-bus network is shown in the figure below, indicating the p.u. impedance of each element :
[Figure] Buses 1, 2, 3 in a line: bus 1 to bus 2 through $j0.25$; bus 2 to bus 3 through $-j0.08$; bus 1 connected to ground through $j0.15$; bus 3 connected to ground through $j0.15$.
Find the bus admittance matrix, $Y_{bus}$, of the network. [10]
- (i) Write the steps involved in DMA data transfer. Also describe the functions of 8085 pins which are used in DMA data transfer. [12]
(ii) Write an 8085 assembly language program to read and complement the contents of the flag register. [8]
- Find the value of $R$ so that the system shown in the figure is critically damped. $V_i(t)$ is the input voltage and output $V_o(t)$ is the voltage across the capacitance. $L = 90\,\mu\mathrm{H}$, $C = 120\,\mathrm{nF}$ :
[Figure] Series $R$ and $L$ in the top line, capacitor $C$ across the output; input $V_i(t)$ at left, output $V_o(t)$ across $C$.
- A discrete memoryless source generates three independent message symbols $m_1$, $m_2$ and $m_3$ with probabilities 0.9, 0.08 and 0.02 respectively.
(i) Design a binary variable length Huffman code. (Assign '0' to the message with highest probability). Determine the average code length, compression ratio and coding efficiency.
(ii) Design a binary first-order extension code for this source and find the average code length for the designed code. Determine the compression ratio and efficiency for the extended code.
- What is the universal relay torque equation? Using this equation, derive the impedance relay, reactance relay and mho relay characteristics. Also draw the operating characteristic and indicate clearly the zones of operation and no operation.
- A single-phase distributor ABC fed at A is shown in the figure below. The impedances of the sections AB and BC are same and equal to $(0.15 + j0.25)\,\Omega$. The power factors are lagging with respect to the voltage at the far end. If the voltage at the far end is 240 V, then determine the supply voltage and its phase angle with respect to the far end :
[Figure] Distributor A to B to C; load at B: 150 A, 0.6 p.f. lagging; load at C: 150 A, 0.8 p.f. lagging.
- The figure shows a unity feedback system with $G(s) = \frac{2}{s(s+1)(s+2)(s+3)}$.
(i) Sketch the approximate polar plot of $G(s)$.
(ii) Determine the closed-loop stability of the system using the polar plot of $G(s)$.
(iii) Determine the gain margin of the system.
[Figure] Unity negative feedback loop with input $R(s)$, forward block $G(s)$, output $C(s)$.
- Two ammeters having resistances of $1\,\Omega$ and $2\,\Omega$ respectively give full-scale deflections with 200 mA and 250 mA respectively. Find the shunt to be connected with these ammeters to extend their range to 20 A. The range extended ammeters are connected in parallel and then placed in a circuit in which a total current of 15 A is flowing. Find the readings of the ammeters.
- Two generating stations having short-circuit capacities of 1500 MVA and 1000 MVA respectively, and operating at 11 kV, are linked by an interconnected cable having a reactance of $0.7\,\Omega$ per phase. Determine the short-circuit capacity of each station after interconnection.