Mains PYQs
UPSC Mains Electrical Engineering paper 1 2023 questions
- Obtain Norton equivalent circuit at terminals ab of the coupled circuit shown in the figure. Using it, find out the current passing through $5\,\Omega$ resistor connected between the terminals ab.
[Figure] Left source $10\angle 0^\circ$ V in series with $4\,\Omega$ and $j8\,\Omega$; right source $10\angle 90^\circ$ V in series with $2\,\Omega$ and $j4\,\Omega$; the two inductors are mutually coupled with $j5\,\Omega$ (dot marked on each); terminals a and b are taken from the junction between the two inductors and the bottom common line.
- Obtain the Laplace transform of the following periodic waveforms :
(i) [Figure] f(t) is a sawtooth: rises linearly from 0 to 1 over 0 to a, drops to 0 at a, and repeats at 2a, 3a, ...
(ii) [Figure] waveform rises linearly from 0 to 1 at t = a, stays at 1 till 3a, falls linearly to 0 at 4a, rises linearly to 1 at 5a and stays at 1 thereafter (marked at a, 3a, 4a, 5a)
- A 3-phase, 50 Hz, star-connected cage-type induction motor has standstill input impedance of $(1.0 + j\,3.0)\,\Omega$ per phase. The motor is connected through a cable from 400 V, 3-phase balanced supply so that the blocked rotor voltage at its terminal is dropped by 20% from the supplied voltage. The motor is to be started through a DOL starter from the same supply and cable as above.
Find :
(i) the cable impedance per phase,
(ii) the motor starting current,
(iii) input power factor at the time of starting.
(Assume negligible stator impedance of the motor and cable R/X ratio of $3:1$ at 50 Hz supply. Also ignore magnetizing current and core losses.)
- Calculate the lower corner frequency for the circuit shown below. Take transistor parameters as : $\beta = 100$, $V_{BE} = 0.7\,\mathrm{V}$ and $V_A = \infty$.
[Figure] BJT amplifier: $V_{CC} = 12\,\mathrm{V}$, $R_1 = 10\,\mathrm{k\Omega}$, $R_2 = 1.5\,\mathrm{k\Omega}$, $R_C = 1\,\mathrm{k\Omega}$, $R_E = 0.1\,\mathrm{k\Omega}$, source $v_i$ with $R_S = 0.5\,\mathrm{k\Omega}$ and coupling capacitor $C_C = 0.1\,\mu\mathrm{F}$ to the base, output $v_o$ at the collector.
- A metal bar slides over a pair of conducting rails in a uniform magnetic field $\vec{B} = \vec{a}_z\, B_0\,\mathrm{Wb/m^2}$ with a constant velocity $\vec{u}$ m/s as shown below in the figure. A resistance 'R' $\Omega$ is connected between terminals 1 and 2. Prove that this system upholds the principle of conservation of energy. Neglect the electrical resistance of the metal bar and the pair of conducting rails, and the mechanical friction of this ideal system.
[Figure] Rails separated by h meters, resistance R across terminals 1 and 2, uniform magnetic field out of the page (z direction), metal bar moving with velocity $\vec{u}$ along X.
- For the circuit shown in the figure, obtain the value of voltage across $0.5\,\Omega$ and $2.5\,\Omega$ resistors using nodal current analysis.
[Figure] Nodes $V_1$, $V_2$, $V_3$, $V_4$ and a ground node; $0.5\,\Omega$ between $V_2$ and $V_3$ (voltage across it marked with polarity); $2\,\Omega$ between $V_3$ and $V_4$; $2.5\,\Omega$ between $V_2$ and $V_1$ (voltage across it marked with polarity); 2 A current source from ground node up to $V_3$; 12 V source between $V_2$ and the ground node (- at $V_2$, + at ground node); dependent current source $0.5\,V_x$ between ground node and $V_4$; $1\,\Omega$ between ground node and $V_1$; dependent voltage source $0.2\,V_y$ between $V_1$ and $V_4$.
- A causal discrete-time LTI system is described by :
$y[n] - \frac{3}{4}y[n-1] + \frac{1}{8}y[n-2] = x[n]$,
where $x[n]$ and $y[n]$ are the input and output of the system respectively.
(i) Determine the system transfer function $H(z)$.
(ii) Find the impulse response $h[n]$ of the system.
(iii) Find the step response $s[n]$ of the system.
- Consider the figure of differential pair given below. Neglecting the early effect, determine the change in $V_X$, $V_Y$, $V_X - V_Y$
if
(i) $V_{CC}$ rises by $\Delta V$ and $R_{C1} = R_{C2} = R_C$.
(ii) $I_{EE}$ experiences a change of $\Delta I$ and $R_{C1} = R_{C2} = R_C$.
(iii) $R_{C1} = R_{C2} + \Delta R$.
[Figure] Differential pair $Q_1$, $Q_2$ with collector resistors $R_{C1}$, $R_{C2}$ to $V_{CC}$, collector nodes X and Y, both bases tied to common-mode source $V_{CM}$, emitters joined to current source $I_{EE}$ to ground.
- (i) Consider the shift register shown in the figure below, which is implemented using D flip-flops and 2 : 1 multiplexers.
[Figure] Four D flip-flops (0 to 3) with outputs $Q_0$ to $Q_3$, common CK and active-low CLR; each D input fed by a 2:1 multiplexer (select = Load) with inputs 0 and 1: for flip-flop 0, input 0 is $X_L$ and input 1 is $X_0$; for flip-flop 1, input 0 is $Q_0$ and input 1 is $X_1$; for flip-flop 2, input 0 is $Q_1$ and input 1 is $X_2$; for flip-flop 3, input 0 is $Q_2$ and input 1 is $X_3$.
Complete the truth table shown as follows :
| CK | CLR (active low) | Load | $Q_3$ | $Q_2$ | $Q_1$ | $Q_0$ |
| X | 0 | X | | | | |
| rising edge | 1 | 0 | | | | |
| rising edge | 1 | 1 | | | | |
Complete the timing diagram below assuming $X_3X_2X_1X_0 = 0101$.
[Figure] Timing diagram with CK (clock pulses), CLR (high, going low near the end), Load (high for the first clock period, then low), $X_L$ (low, high for a short interval in the later part, then low), and blank traces for $Q_0$, $Q_1$, $Q_2$, $Q_3$. [10]
(ii) Use 4 : 1 multiplexer and logic gates to implement the function :
$F(A,B,C,D) = \sum m\,(3, 4, 5, 6, 7, 9, 10, 12, 14, 15)$ [10]
- (i) The figure shows a triangular pulse which is zero for all time except $-\frac{a}{2} \le t \le \frac{a}{2}$. For this pulse
(I) determine the Fourier transform.
(II) sketch the continuous amplitude spectrum.
[Figure] f(t) is a triangle with peak $V_0$ at t = 0, falling linearly to 0 at $t = -\frac{a}{2}$ and $t = \frac{a}{2}$. [10]
(ii) Find $\mathcal{L}^{-1}[F_1(s)\,F_2(s)]$ by using convolution for the following $F_1(s)$ and $F_2(s)$.
$F_1(s) = \frac{s}{s+1}$ $F_2(s) = \frac{1}{s^2+1}$ [10]
- An inverting Op-Amp circuit is to be designed such that the weighted sum $v_0 = -(v_1 + 4v_2)$. Resistors $R_1$, $R_2$ and $R_f$ are to be chosen in a way that for a maximum output voltage of 4 V, the current in the feedback resistor does not exceed 1 mA.
[Figure] Inverting summing amplifier: $v_1$ through $R_1$ and $v_2$ through $R_2$ to the inverting input, $R_f$ from output $v_0$ to inverting input, non-inverting input grounded.
Calculate the values of $R_1$, $R_2$ and $R_f$.
- For the circuit shown below, early voltage $V_A = \infty$ and $\beta = 100$. Find the reverse saturation current if :
(i) the collector current of $Q_1 = 0.5\,\mathrm{mA}$.
(ii) $Q_1$ is biased at the edge of saturation.
[Figure] $V_{CC} = 2.5\,\mathrm{V}$; $50\,\mathrm{k\Omega}$ from $V_{CC}$ to base and $30\,\mathrm{k\Omega}$ from base to ground; $3\,\mathrm{k\Omega}$ collector resistor to $V_{CC}$; emitter of $Q_1$ grounded.
- Consider the control circuitry of a machine copier with four switches as shown below in the figure. These switches are at various points along the path of the machine. Each switch is normally open and closes only when the paper passes over it. Let there be a restriction that switch 1 and switch 4 cannot close simultaneously. Use Karnaugh map to design a logic circuit that produces a high output whenever two or more switches are closed at the same time.
[Figure] Switches SW1 to SW4, each connected to 5 V through a resistor and to a logic circuit with output X.
(SW1, SW2, SW3, SW4 : Switch 1, Switch 2, Switch 3, Switch 4)
- The experimental data for the two-port network shown in the figure is given in the table.
[Figure] Two-port network with $V_{S1}$ and $I_1$ at port 1, $V_{S2}$ and $I_2$ at port 2.
| | $V_{S1}$ Volts | $V_{S2}$ Volts | $I_1$ Amp | $I_2$ Amp |
| Experiment 1 | 100 | 50 | 5 | -30 |
| Experiment 2 | 50 | 100 | -20 | -5 |
| Experiment 3 | 25 | 0 | - | - |
| Experiment 4 | - | - | 5 | 0 |
Obtain Z-parameters, Y-parameters and fill in the missing data.
- A 400 V, 50 Hz, 3-phase star-connected cylindrical rotor synchronous motor has synchronous impedance of $(0.5 + j\,2.5)\,\Omega$ per phase. It develops a maximum power of 50 kW at rated terminal voltage. Find the excitation voltage, motor current and input power factor under maximum power condition.
- A half-controlled converter fed from 240 V, 50 Hz single-phase ac source is feeding 1800 W power to a 100 V battery as shown in the figure below. The battery is connected in series with a large inductance and a resistance of $2\,\Omega$. The inductance is large enough to make the load current flat and continuous.
Find :
(i) the triggering angle of the thyristors,
(ii) rms value of fundamental component of converter input current, and
(iii) the input power factor in the ac side.
(Assume the inductor has a resistance of $1\,\Omega$)
[Figure] Single-phase half-controlled bridge with two thyristors (top) and two diodes (bottom), a freewheeling diode across the output, load of $2\,\Omega$ in series with L = Large and a 100 V, 1800 W battery; supply 240 V, 50 Hz.
- A signal x(t) is described as
$$x(t) = \left(\frac{5}{2}\right)\cos\left(160\times10^3\pi t\right) + 7\cos\left(170\times10^3\pi t\right) + \left(\frac{5}{2}\right)\cos\left(180\times10^3\pi t\right)$$
Show that this is an Amplitude modulated signal.
Find :
(i) the ratio $P_s/P_c$ where $P_s$ is power in side bands and $P_c$ is power in carrier.
(ii) the power efficiency in this AM signal.
- When a transmission line of characteristic impedance $50\,\Omega$ is short-circuited at the termination, the voltage minima were found to be 25 cm apart. If the short circuit is replaced by unknown load impedance $Z_L\,\Omega$, the minima shifted 8 cm towards the load and the standing wave ratio was found to be 4. Calculate the unknown load impedance $Z_L$.
- In the series RLC circuit shown in the figure, the capacitor has an initial charge $Q_0 = 1\,\mathrm{mC}$ and the switch is in position 1 long enough to establish the steady state. Find the transient current which results when the switch is moved from position 1 to 2 at t = 0.
[Figure] 10 V source (+ on top) connected through switch position 1; capacitor $200\,\mu\mathrm{F}$ with initial charge $Q_0$ (+ at the bottom plate); switch position 2 connects the capacitor to the series $5\,\Omega$ and $0.1\,\mathrm{H}$ branch; current $i_0$ marked.
- A 200 V, 1100 rpm, dc shunt motor takes 1.5 A and runs at 1150 rpm under no load condition at rated voltage. Its armature resistance including brushes is $0.5\,\Omega$. While running under full load, its field circuit gets open circuited due to fault and the motor takes 5 times of its rated input current to deliver rated torque.
Find :
(i) the full load torque of the machine, and
(ii) the speed of the motor under field fault condition.
Assume no armature copper losses at no load and no armature reaction.
- An absorber material of relative permeability and relative permittivity of $\varepsilon_r = \mu_r = 6 - j6$ is coated on a perfectly conducting sheet and this combination is placed in free space as shown in the figure given below. A 500 MHz wave is incident on it normally from free space. Calculate the thickness of the absorber required to attenuate the reflected wave by 30 dB.
[Figure] Incident wave from the left in free space onto an absorber material layer coated on a conducting sheet; thickness of the absorber marked.
- A 120 V, 1000 rpm, 350 W separately excited dc motor is supplied via half-controlled single-phase bridge rectifier for speed control purpose. The supply voltage to the rectifier is 200 V, 50 Hz ac and to obtain the desired speed, the triggering angle is set at $105^\circ$ at one instant. The armature current is discontinuous with an average value of 2 A and it continues up to $30^\circ$ beyond voltage zero. The motor armature resistance is $1.5\,\Omega$. Determine the operating speed of the motor.
(Assume constant flux operation and no armature reaction)
- A 400 V, 3-phase, 50 Hz, star-connected synchronous motor has per phase synchronous impedance $Z_s = (0.5 + j\,3.5)\,\Omega$. It is required to operate the motor as synchronous condenser to deliver 100 kVAr at rated voltage and no load. Find the motor current and excitation voltage under this condition. (Assume zero motor input power at no load)
- (i) Two statistically independent Poisson random variables $X_1$ and $X_2$ with respective parameters $\lambda_1$ and $\lambda_2$ are added to form $Y = X_1 + X_2$.
Show that the random variable Y is Poisson distributed with parameter $(\lambda_1 + \lambda_2)$. [10]
(ii) Derive the relationship between Binomial and Poisson random variables when Binomial distribution becomes equal to the Poisson distribution. [10]
- The circuit given in the figure below is in steady state initially before the thyristor is triggered. The thyristor is triggered at t = 0. Calculate
(i) the maximum current the thyristor will carry.
(ii) the instant of carrying maximum current by the thyristor.
(iii) the conduction time of the thyristor.
(Assume zero latching and holding current for the thyristor)
[Figure] 200 V source, $4\,\Omega$ resistor, capacitor $1.5\,\mathrm{mF}$, inductor $3.0\,\mathrm{mH}$ and a thyristor connected as shown; the capacitor is in a branch across the thyristor-inductor path.
- A 415 V, 4-pole, 3-phase, 50 Hz, star-connected squirrel cage induction motor has per phase parameters of $r_s = 1.1\,\Omega$, $r_r = 1.3\,\Omega$, $X_m = 167\,\Omega$, and $X_{ls} = X_{lr} = 3.5\,\Omega$, all at rated frequency. The motor has a rated slip of 4%. Its speed is to be controlled by VVVF method using a VSI (Voltage Source Inverter). Find the voltage to be applied to the motor at 5 Hz operating frequency to maintain same peak torque as in 50 Hz. Also determine the speed at which rated torque appears at this frequency.
(Neglect core losses in the motor and all motor parameters referred from stator side)
- (i) A 300 W carrier is modulated to a depth of 70%. Calculate the total power transmitted in case of Vestigial Side Band (VSB) modulation. Assume 15% of the other side band is transmitted along with wanted side band. Also find the saving in power when compared to Double Side Band (DSB) transmission. [10]
(ii) Find the temperature of the attenuator in the system shown in the figure below so that the overall noise figure of the system does not exceed 3.5 dB. The attenuator introduces a loss of 3 dB.
[Figure] Cascade of Attenuator (loss = 3 dB), Amplifier (Gain = 1000, Noise figure = 1.5 dB) and Mixer (Gain = 100, Noise figure = 8 dB). [10]
- A bank of three identical single-phase transformers having 11000 V / 231 V voltage ratio are connected in delta-star combination with delta side connected to 11 kV, 3-phase balanced supply. The star side is supplying a balanced load of 120 kVA at 0.8 pf lag. A single-phase load of 40 kW, upf is now connected between one line and neutral of the secondary side. Calculate the input line currents at the delta side under this condition.
(Neglect any magnetising currents of the transformers)