Mains PYQs
UPSC Mains Electrical Engineering paper 2 2022 questions
- A closed-loop system is shown in the figure below. The maximum overshoot for the system is 40% and the peak time is 2 seconds. Calculate the values of $A$ and $B$. Consider $J = 1\,\mathrm{kg\text{-}m^2}$ :
[Figure]
Block diagram: $R(s)$ into a summing junction, then a second summing junction, then block $\frac{A}{Js}$, then block $\frac{1}{s}$ to $C(s)$; inner feedback from the output of $\frac{A}{Js}$ through block $B$ to the second summing junction; outer unity feedback from $C(s)$ to the first summing junction.
- Draw the Nyquist plot for the system shown below. Using Nyquist stability criterion, determine the range of $K$ for which the system is stable. Assume $K \in \mathbb{R}$ (set of real numbers) :
[Figure]
Block diagram: $R$ into summing junction, then gain $K$, then $\frac{1}{s^2 + 2s + 2}$ to output $Y$; feedback path through $\frac{1}{s + 1}$ to the summing junction.
- Show an instruction cycle with possible machine cycles and clock cycles (T-states) in it, for the microprocessor 8085. If the processor is working at 3 MHz, calculate the minimum and maximum possible execution time for an instruction.
- The distributed capacitance of a coil is resonated at 10 MHz with 100 pF in parallel and is then again resonated at twice the frequency with 16 pF. Calculate its equivalent distributed capacitance and the inductance of the coil.
- In a symmetrical three-phase system supplying a balanced load of 28 A at 400 V, a wattmeter reading is 5 kW, when its current coil is connected in the red phase and its voltage coil is connected between the neutral and red phase. Determine the instrument reading for the phase sequence RYB, if the voltage coil is connected between the blue and yellow phases. (The current coil remains unchanged)
- A unity feedback system is shown in the figure below. Determine the range of $\alpha$ for which the system is stable and the steady-state error for unit step input is less than 5% :
[Figure]
Unity feedback loop with forward transfer function $\frac{s + \alpha}{s^3 + (1 + \alpha)s^2 + (\alpha - 1)s + (1 - \alpha)}$, input $R(s)$, output $C(s)$.
- Explain each step of the assembly language program given below for microprocessor 8085 and calculate the total time taken by the processor in its execution if the processor is working at 3 MHz. (The number of clock cycles for instructions is given in the table for reference) :
LXI SP, 5000 H
LXI D, 00F9 H
CALL SUBROUTINE 1
HLT
SUBROUTINE 1 : DCX D
MOV A, D
ORA E
JNZ SUBROUTINE 1
RET
| Instruction | Clock cycle |
|---|---|
| LXI | 10 |
| CALL | 18 |
| DCX D | 6 |
| MOV A, D | 4 |
| ORA E | 4 |
| JNZ | 7/10 (for Z=1 or 0) |
| RET | 10 |
- A resistance strain gauge having a resistance of 100 $\Omega$ and gauge factor of 2 is connected in series to a load resistance of 200 $\Omega$ across 24 volts. The modulus of elasticity is 200 $\mathrm{GN/m^2}$. Calculate the change in output voltage due to the applied stress of 120 $\mathrm{MN/m^2}$.
- (i) The figure below shows a schematic diagram of shunt ohmmeter. It consists of a battery in series with an adjustable resistance $R_1$ and a d.c. measuring PMMC ammeter. The unknown resistance $R_x$ to be measured is connected across the terminals $A$-$B$. $S$ is the off-on switch. Write down its design equations. What are your observations when the terminals $A$-$B$ are shorted and open-circuited? [10]
[Figure]
Battery E in series with adjustable $R_1$ (current $I_1$) and switch S; basic meter (current $I_m$, resistance $R_m$) across terminals A and B; $R_x$ connected across A-B.
(ii) Determine the value of the resistor in series with the battery to adjust the full-scale deflection and the point (in %) of full scale at which 100 $\Omega$ will be marked on the scale. Consider the e.m.f. of internal battery as 2 volts, full-scale current of 2 mA and an internal resistance of 20 $\Omega$. [10]
- Consider the system
$$\dot{\bar{x}} = \begin{bmatrix} 0 & 16 & 0 & 0 \\ -1 & -8 & 0 & 0 \\ 4 & 8 & 1 & 15 \\ 0 & 0 & 3 & -3 \end{bmatrix} \bar{x} + \begin{bmatrix} 0 \\ 0 \\ 1 \\ 0 \end{bmatrix} u$$
(i) Find the eigenvalues of this system.
(ii) Find the controllable and uncontrollable modes of this system.
(iii) Show that there are an infinite number of feedback gains $K$ that will relocate the modes of the system to $-5$, $-3$, $-4$, $-4$.
(iv) Find the unique matrix $\overline{K}$ that achieves these pole locations and prevents initial conditions on the uncontrollable part of the system from ever affecting the controllable part.
- (i) Explain the use of MAR in interfacing the external memory to processor.
(ii) Name various 8-bit and 16-bit internal registers in microprocessor 8085 and also, indicate which 8-bit registers can be paired to act as 16-bit register in several instructions.
- (i) List various interrupts in microprocessor 8085 in order of decreasing priority. Specify which of these are edge-sensitive and which are level-sensitive.
Explain why TRAP is having good noise immunity as compared to other interrupts.
(ii) What will be the action of running the given assembly program segment?
MVI A, 0B H
SIM
- The values of the components in the Maxwell bridge for balance condition are shown below in the circuit diagram. Write the balance equation and calculate the values of $L_s$, $R_s$ and $Q$ for the unknown sample coil :
[Figure]
Maxwell bridge fed by 5 V AC, 100 Hz; $R_1 = 1\mathrm{K}6$; unknown sample coil ($L_s$ in series with $R_s$); detector D; $R_3 = 400\mathrm{E}$ in parallel with variable $C_3 = 0.2\,\mu\mathrm{F}$; $R_4 = 500\mathrm{E}$.
- Determine the transfer function $C(s)/R(s)$ for the signal flow graph of the system shown below using Mason's gain formula :
[Figure]
Signal flow graph: forward path $R(s)$, $G_1(s)$, $G_2(s)$, $G_3(s)$, $G_4(s)$ to $C(s)$; a self-loop of $-1$ at the node after $G_1$; feedback branches of $-1$ from the $C(s)$ side back to the node after $G_1$, to the node after $G_2$ and to the node after $G_3$.
- Determine the inductance of a single-phase transmission line consisting of three conductors of 2 cm radii in the 'go' conductor and two conductors of 4 cm radii in the 'return' conductor as shown in the figure below :
[Figure]
Composite conductor A: conductors a, b, c in a vertical line with 4 m spacing between a and b and between b and c. Composite conductor B: conductors a', b' in a vertical line 4 m apart, 6 m horizontally from conductor A.
- The schematic diagram of a radial transmission system is shown in the figure below. The ratings and reactances of various components are shown therein. A load of 60 MW at 0.9 power factor lagging is tapped from 66 kV substation which is to be maintained at 60 kV. Calculate the terminal voltage of the synchronous generator :
[Figure]
Generator at bus $V_1$, 11/220 kV transformer (100 MVA, $X = 12\%$), line of $j100\,\Omega$, 220/66 kV transformer (100 MVA, $X = 10\%$), 60 kV bus $V_2$ feeding a load of 60 MW at 0.9 pf lagging.
- Explain how arc is initiated and sustained in a circuit breaker when the circuit breaker contact separates. Also, derive an expression for the restriking voltage in terms of system voltage, inductance and capacitance, across the circuit breaker contacts. (Assume that the neutral of the system is solidly grounded)
- Show that, with a non-uniform quantizer, the mean square value of the quantization error is approximately equal to $\frac{1}{12}\sum_i \Delta_i^2 p_i$, where $\Delta_i$ is the $i$th step size and $p_i$ is the probability that the input signal amplitude lies within the $i$th interval. Assume that the step size $\Delta_i$ is small compared with the excursion of the input signal.
- Prove that all vectors in the same coset have the same syndrome that is unique to that coset in the standard array for any linear block code.
- A three-phase, 50 Hz transmission line is 400 km long. The voltage at the sending end is 220 kV. The line parameters are $r = 0.125\,\Omega/\mathrm{km}$, $x = 0.4\,\Omega/\mathrm{km}$ and $y = 2.8 \times 10^{-6}$ mho/km.
(i) Find the sending-end current and receiving-end voltage when there is no load on the line. Comment on the result.
(ii) Find the maximum permissible line length if the receiving-end no-load voltage is not to exceed 230 kV.
(iii) Find the maximum permissible line frequency if the no-load voltage is not to exceed 250 kV.
- (i) Two 11 kV, 25 MVA, three-phase, star-connected generators $G_1$ and $G_2$ operate in parallel. The positive, negative and zero sequence reactances of each generator are $j0.09$ pu, $j0.05$ pu and $j0.04$ pu respectively. A single line to ground fault occurs at the terminals of one of the generators. Find the fault current in pu. Also, find the voltage across the grounding resistor $R_n$ in pu. Assume that the neutral of only generator $G_1$ is grounded through a resistor $R_n = 1\,\Omega$. [10]
(ii) A 50 Hz, 11 kV, three-phase synchronous generator with earthed neutral has a reactance of $4\,\Omega$/phase and is connected to a busbar through a circuit breaker (CB). The capacitance to earth for the CB and generator is $0.02\,\mu\mathrm{F}$ per phase, and resistance may be ignored. Find the maximum voltage across the contacts of the circuit breaker, frequency of the transient oscillation and the average rate of rise of restriking voltage up to the first peak of the oscillation. [10]
- Find the capacity of the cascade connection of $n$ binary symmetric channels with the same crossover probability $\varepsilon$. What is the capacity when the number of channels goes to infinity?
- The figure below shows the encoder for a rate $r = \frac{1}{2}$, constraint length $k = 4$ convolutional code :
[Figure]
Encoder: input into a chain of three flip-flops (F/F); two modulo-2 adders taking taps from the input and flip-flop outputs, producing $g^{(1)}(x)$ and $g^{(2)}(x)$; a commutator switch selects the output.
(i) Determine the encoder output produced by the message sequence 11011 ... .
(ii) Also, construct the code tree for the encoder. Trace the path through the tree that corresponds to the message 11011 ... . Compare the resulting output with that determined in (i).
- (i) Explain in brief about the necessity of automatic load frequency control in the power generating system. Draw the schematic diagram of load frequency and voltage control regulators. [10]
(ii) Two generators rated 200 MW and 400 MW are operating in parallel. The droop characteristics of their governors are 4% and 6% respectively from no load to full load. Assuming that the governors are operating at 50 Hz at no load, how would a load of 600 MW be shared between them? What would be the corresponding system frequency at this load? Assume free governor operation. [10]
- Explain in brief about different types of HVDC links, their advantages and disadvantages.
- (i) Write the recommended expression for time-current relationship of standard IDMT relay and draw its characteristic curve. Why is this type of relay commonly used for protection of electrical machines?
(ii) Draw the circuit arrangements for connecting earth fault relay in $3\phi$ supply and explain its working for core balance current transformer as well as for three CT system.
- The received signal in a binary communication system that employs antipodal signals is $r(t) = s(t) + n(t)$, where $s(t)$ is shown in the figure below and $n(t)$ is AWGN with power spectral density $\frac{N_0}{2}\,\frac{\mathrm{W}}{\mathrm{Hz}}$ :
[Figure]
Plot of $s(t)$: amplitude $A$ for $0 < t < 1$ and for $2 < t < 3$, zero elsewhere.
(i) Sketch the impulse response of the filter matched to $s(t)$.
(ii) Sketch the output of the matched filter when the input is $s(t)$.
(iii) Determine the variance of the noise at the output of the matched filter at $t = 3$.
(iv) Determine the probability of error as a function of $A$ and $N_0$.
- Find the steady-state power limit of a system consisting of a generator having equivalent reactance of 0.5 pu, connected to an infinite bus through a series reactance of 1.0 pu. The terminal voltage of the generator is held at 1.20 pu and the voltage of the infinite bus at 1.0 pu.