Mains PYQs
UPSC Mains Electrical Engineering paper 1 2022 questions
- For the circuit shown in Figure 1(a), find the $V_{in}$, $V_s$ and power supplied by the dependent source.
[Figure]
Circuit: 2 A through 5 $\Omega$ and a 60 V source in series from $V_{in}$; node with $i_x$ flowing down through 3 $\Omega$ and source $V_s$; 2 $\Omega$ with 8 A on the right; dependent voltage source $4i_x$ on the right branch.
- Calculate the forward current caused by 0.8 V forward voltage across the diode with ideality factor of semiconductor material as 1. The reverse saturation current of diode is $12.674 \times 10^{-13}$ A at a temperature of 22°C.
[Assume Boltzmann constant $K = 1.38 \times 10^{-23}\,\mathrm{JK^{-1}}$, charge of electron $q = 1.6 \times 10^{-19}$ C]
- Find the efficiency of a long shunt compound generator rated at 250 kW, 230 V when supplying 75% rated load at rated voltage. The resistances of armature and series field are 0.009 $\Omega$ and 0.003 $\Omega$ respectively. The shunt field current is 13 A. When the machine is running as a motor at no-load, the armature current is 25 A at rated voltage.
- An op-amp circuit is shown in Figure 1(d) below. Assume the op-amp to be ideal.
(i) Determine $I_1$, $I_2$, $I_3$ and $V_X$.
(ii) If $V_o$ is not to be lower than $-13$ V, calculate the maximum allowed value for $R_L$.
(iii) If $R_L$ is varied in the range 100 $\Omega$ to 1 k$\Omega$, what is the corresponding change in $I_L$ and in $V_o$ ?
[Figure]
Inverting op-amp: 1 V source through $I_1$ and 10 k$\Omega$ to the inverting input; feedback path with $I_2$, 10 k$\Omega$ to node $V_X$, then variable $R_L$ with $I_L$ to output $V_o$; $I_3$ flows up from a 100 $\Omega$ resistor at $V_X$ to ground; non-inverting input grounded.
- Explain the parity bit generator and parity bit checker. Realize the even parity bit generator and even parity bit checker using X-OR gate.
- (i) For the circuit shown in Figure 2(a)(i), initial current through the coil is zero. The switch is closed at time $t = 0$.
Find the time domain expression of current flowing through the coil for $t \ge 0$. How long will it take for the coil current to reach 95% of its final value and what is the final value of this current ? [10]
[Figure]
Circuit: 100 V source in series with 50 $\Omega$ and switch S (closing at $t = 0$), feeding 100 $\Omega$ in parallel with a 4 H coil carrying $i_L(t)$.
(ii) Obtain the Thevenin's equivalent of the network shown in Figure 2(a)(ii), across the terminals XY. [10]
[Figure]
Circuit: 4 V source, 2 k$\Omega$ series, a dependent current source $\frac{V_x}{4\,\mathrm{k}\Omega}$ (arrow up) across the shunt branch, 3 k$\Omega$ series to terminal X, $V_x$ measured across XY.
- (i) Determine the Inverse Laplace Transform of the following function :
$$F(s) = \frac{s^3 + 7s^2 + 14s + 11}{s^3 + 6s^2 + 11s + 6}$$ [6]
(ii) Find the initial and final value of the current whose Laplace Transform is given below :
$$I(s) = \frac{0.32}{s\,(s^2 + 2.42s + 0.672)}$$ [4]
(iii) Solve the following differential equation :
$$\frac{d^2 i}{dt^2} + \frac{di}{dt} = t^2 + 2t$$
Given that $i(0-) = 4$ and $\left(\frac{di}{dt}\right)_{0-} = -2$. [10]
- A single phase AC bridge rectifier as shown in Figure 2(c) is operating at firing delay angle $\alpha = 45°$. The thyristor $T_3$ gets damaged and behaves as an open circuit. Calculate the value of load resistance R if load current is 3.1556 A.
[Figure]
Single phase bridge of thyristors $T_1$, $T_2$, $T_3$, $T_4$ fed from 200 V, 50 Hz, with load R carrying $i_L$.
- A common-emitter amplifier circuit is shown in Figure 3(a). Neglect $r_x$ and $r_o$ and assume the current source to be ideal.
[Figure]
Common-emitter BJT with $V_{sig}$ and $R_{sig}$ at the base, $R_C$ to $V_{CC}$ at the collector, output through $C_C$ to $R_L$ and $V_o$, and emitter with bypass capacitor $C_E$ and an ideal current source $I$ to the supply.
(i) Derive an expression for the midband gain.
(ii) Derive expressions for the break frequencies caused by $C_E$ and $C_C$.
(iii) Give an expression for the amplifier voltage gain A(s).
(iv) For $R_{sig} = R_C = R_L = 10$ k$\Omega$, $\beta = 100$ and $I = 1$ mA, find the value of the midband gain.
(v) Select values for $C_E$ and $C_C$ to place the two break frequencies a decade apart and to obtain a lower 3 dB frequency of 100 Hz while minimizing the total capacitance.
(vi) Sketch a Bode plot for the gain magnitude and estimate the frequency at which the gain becomes unity.
- (i) Apply the Routh-Hurwitz (R-H) criterion to the polynomial $P(s) = s^4 + 4s^3 + 8s^2 + 12s + 15$ in order to determine the number of roots, with positive real parts, with zero real parts and with negative real parts. Also, state about the stability of the system represented by P(s). [10]
(ii) For the network shown in the Figure 3(b)(ii), find the impulse response. [10]
[Figure]
Circuit: source $v_{in}(t)$, 1 $\Omega$ series, 1 H series, 3 $\Omega$ load; 1 F capacitor across the middle node with $v_o(t)$ measured across it.
- A 4-pole single phase 50 Hz induction motor is having values of $R_2$ and $X_2$ equal to 0.02 ohm and 0.5 ohm respectively. Calculate the slip for maximum torque and the speed corresponding to maximum torque. Stator resistance and leakage reactance are to be neglected.
- For the network shown in Figure 4(a)(i) and its excitation function shown in Figure 4(a)(ii), find the response $v(t)$ using convolution by :
(i) 's' domain approach.
(ii) time domain analytical approach.
(iii) graphical convolution approach.
[Figure]
Figure 4(a)(i): source $e(t)$ in series with 1 $\Omega$, 1 F capacitor across output, output $u(t)$. Figure 4(a)(ii): $e(t)$ is a rectangular pulse of height V from $t = 0$ to $t = 1$.
- (i) A 240 V, 50 Hz single phase supply is connected to a full controlled converter to control the speed of a 10 kW, 220 V separately excited dc motor. The rated current of motor at full load is 25 A, armature resistance is 0.4 ohm and machine constant is 0.3 V/rpm. Calculate the speed of motor when converter is operating at an angle $\alpha = 50°$, assuming continuous armature current. [10]
(ii) Describe the performance requirements of a chopper circuit that can perform the chopping functions in any modulation technique. [10]
- The amplifier shown in Figure 4(c) is biased to operate at $I_D = 1$ mA and $g_m = 1$ mA/V. Neglecting $r_o$,
(i) determine the midband gain.
(ii) determine the value of $C_S$ that places $f_L$ at 10 Hz.
[Figure]
MOSFET common-source amplifier: $R_D = 10$ k$\Omega$ from $V_{DD}$ to drain, output $V_o$ at drain, source with $R_S = 6$ k$\Omega$ in parallel with bypass capacitor $C_S$, input $V_i$ at gate.
- The diagram of Master-Slave S-R flip-flop and the waveform applied to the Master flip-flop is shown in Figure 5(a). Draw the waveform that appears at the output of Slave flip-flop.
[Figure]
Master-Slave S-R flip-flop built from NAND gates $G_1$ to $G_8$ with inputs S, C, R and outputs $Q_2$, $\overline{Q_2}$. Input waveforms: CLK with four pulses numbered 1 to 4; S high during the interval from the end of pulse 1 to the end of pulse 2, low otherwise; R high until the end of pulse 1, low from there to the end of pulse 2, high from there to the end of pulse 3, then low.
- An ideal lossless $\frac{\lambda}{4}$ extension line of $Z_o = 60\,\Omega$ is terminated with a load resistance of 60 $\Omega$. Find the value of $Z_{in}$.
- The power supplied to a 3-phase induction motor is 40 kW and the corresponding stator losses are 1.5 kW. Calculate the net (shaft) mechanical power developed and the rotor Cu loss, when the slip is 0.04 pu. What will be the net power developed if the speed of the above motor is reduced to 40% of the synchronous speed by means of external rotor resistance, assuming the torque and stator losses remain unaltered ? Friction and windage losses may be assumed to be 0.8 kW.
- An audio frequency signal $10\sin(2\pi \times 500\,t)$ is used to amplitude modulate a carrier of $50\sin(2\pi \times 10^5\,t)$. Determine :
(i) the modulation index
(ii) the amplitude of each sideband frequency
(iii) the bandwidth required
(iv) total power delivered to the load of 500 $\Omega$
(v) and draw the frequency spectrum.
- For a two-port network, the currents $I_1$ and $I_2$ are as given below :
$I_1 = 2V_1 - V_2$
$I_2 = -V_1 + 2V_2$
Find the transmission and hybrid parameters of the network.
- The plane wave $\mathbf{E} = 30\cos(\omega t - z)\,\mathbf{a}_x$ V/m in air normally hits a lossless medium ($\mu = \mu_0$, $\varepsilon = 4\varepsilon_0$) at $z = 0$.
(i) Find reflection coefficient ($\Gamma$), transmission coefficient ($\tau$), standing wave ratio (S).
(ii) Calculate the reflected electric and magnetic fields.
- Determine the value of inductance L, capacitance C and duty cycle of a buck regulator shown in Figure 6(b). The input voltage is 16 V, output voltage is 4 V, and ripple voltage (peak-to-peak) is 30 mV. The regulator is operating at 20 kHz switching frequency and peak-to-peak ripple current in inductance is 0.75 A.
[Figure]
Buck regulator: input $V_s = 16$ V, series inductor L, diode, freewheeling device across the input side, output capacitor C and LOAD with $V_a = 5$ V.
- Using the superposition theorem find the voltage 'V' across the 5 $\Omega$ resistance in the circuit as shown in Figure 6(c).
[Figure]
Circuit: 2 A current source (arrow up) on the left, 5 $\Omega$ with V across it, 10 $\Omega$ in the top branch, 2 $\Omega$ shunt, 4 A current source (arrow up) on the right.
- A three-phase, 5 kW, 440 V, 6 pole, star connected synchronous motor having negligible stator resistance and synchronous reactance of 6 $\Omega$ is operated at 0.8 rated power factor lagging. Calculate the following :
(i) Torque angle at full load
(ii) Pull-out torque
(iii) Armature current and power factor at half the rated torque
- X and Y are two independent random variables with probability density functions given by
$$f_X(x) = \begin{cases} \frac{1}{4} & \text{for } -2 \le x \le 2 \\ 0 & \text{otherwise} \end{cases}$$
and
$$f_Y(y) = \begin{cases} A\,e^{-3y} & \text{for } 0 \le y < \infty \\ 0 & \text{otherwise.} \end{cases}$$
(i) Determine A.
(ii) Determine the probability density function of $Z = 3X + 4Y$.
- Evaluate both sides of Stokes theorem for the field $\mathbf{H} = (2\rho z\,\mathbf{a}_\rho + 3z\sin\varphi\,\mathbf{a}_\varphi - 4\rho\cos\varphi\,\mathbf{a}_z)$ A/m and for the open surface defined by $z = 1$, $0 < \rho < 2$ m, $0° < \varphi < 45°$.
- (i) Differentiate between the functions of Decade counter and BCD counter with example. [10]
(ii) Draw the diagram of cascading BCD adders to add two three-digit decimal numbers. Also explain the function of this adder with suitable example. [10]
- (i) A DSB-SC signal is transmitted over a noisy channel, with the power spectral density of the noise being as shown in Figure 8(b)(i). The message bandwidth is 4 kHz and the carrier frequency is 200 kHz. Assuming that the average power of the modulated wave is 10 watts, find the output signal-to-noise ratio of the receiver. [10]
[Figure]
Figure 8(b)(i): triangular PSD with peak $10^{-6}$ W/Hz at $f = 0$, falling to zero at $-400$ and $400$ (f in kHz).
(ii) Consider the system shown in Figure 8(b)(ii). The signal x(t) is defined by :
$x(t) = A\cos 2\pi f_c t$
The low-pass filter has unity gain in the passband and bandwidth W, where $f_c < W$. The noise n(t) is white with two-sided power spectral density $\frac{1}{2}N_0$. Determine the signal-to-noise ratio of y(t). [10]
[Figure]
Figure 8(b)(ii): x(t) and n(t) summed, then two differentiators $\frac{d}{dt}$ in cascade, then a low-pass filter giving y(t).
- A single phase transformer, 2400/240 V, 10 kVA, 50 Hz has core loss of 153 W and full load copper loss of 224 W. Find all day efficiency for the following loading cycle : 25% overload for 2 hours, full load for 6 hours, half load for 8 hours, quarter load for 4 hours and no load for 4 hours. All loads are at unity p.f.