Mains PYQs
UPSC Mains Electrical Engineering paper 2 2021 questions
- A system is described by the following state equations:
$\dot{x}_1 = x_1 + x_2 + 3x_3$
$\dot{x}_2 = 2x_1 + 3x_2 + u_1$
$\dot{x}_3 = 2x_2 + x_3 + u_2$
Check the controllability of the system.
- A single phase, single line diagram of a power system is shown in figure. Find the sending end voltage and the value of load resistance in p.u. referred to sending end if the voltage across load resistance is 9.8 kV.
[Figure]
Figure: $V_S$ to a transformer 11/33 kV, 10 MVA, X = 10%, then a transformer 33/10 kV, 10 MVA, X = 12%, to $V_R$ across an $8\,\Omega$ load.
- Explain the following related to computer programming:
(i) Machine Language
(ii) Assembly Language
(iii) Compiler
(iv) Interpreter
(v) ASCII
- A current of $(0{\cdot}5 + 0{\cdot}3\sin\omega t - 0{\cdot}2\sin 2\omega t)$ amps is passed through the circuit shown in figure. Determine the reading of each instrument if $\omega = 10^6$ rad/sec.
[Figure]
Figure: 1 mH inductor and $1000\,\Omega$ resistor in series carrying current $i$ through two ammeters (MC and MI types); two electrostatic voltmeters connected across parts of the circuit.
- A DPCM system uses a linear predictor with a single tap. The normalized autocorrelation function of the input signal for a lag of one sampling interval is 0.75. The predictor is designed to minimize the prediction error variance. Determine the processing gain attained by the use of this predictor.
- Draw the sequence networks and calculate the load sequence impedances of a load circuit as shown in figure. The load circuit is connected to a balanced three phase supply. The value of $z_1$, $z_2$ and $z_n$ are $(4 + j6)\,\Omega$, $-j45\,\Omega$ and $j4\,\Omega$.
[Figure]
Figure: terminals R, Y, B; a star of three impedances $z_1$ meeting at N, with N earthed through $z_n$; and a delta of three impedances $z_2$.
- For the network shown in figure, draw a block diagram representing each circuit element by a block. Use block diagram reduction technique to obtain the transfer function of the network. The voltage $V_i(t)$ is the applied input and the voltage across the capacitor $V_o(t)$ is the output.
[Figure]
Figure: RC ladder: series $R_1$ then node $V_1(t)$ with shunt $C_1$, series $R_2$ then shunt $C_2$ with output $V_o(t)$; currents $I_1(t)$, $I_2(t)$.
- A convolutional code is described by
$g_1 = [1\ 1\ 0]$, $g_2 = [1\ 0\ 1]$, $g_3 = [1\ 1\ 1]$.
Find the transfer function and the free distance for this code. Also verify whether or not this code is catastrophic.
- A solidly earthed 400 KV, 3 phase busbar system is connected with two incoming and four outgoing lines (feeders). A differential protection is provided with switchgear of 4000 MVA capacity having the following parameters:
CT secondary resistance = $0{\cdot}8\,\Omega$
Lead wire resistance = $1{\cdot}2\,\Omega$
Relay load = $1{\cdot}0\,\Omega$
CT magnetization current = $0{\cdot}3$ mA/V
Max. full load current in one feeder = 100 A
Voltage setting of over current relay = 100 V
If the O.C. relay in the spill path is set at 1.0 A, find the following:
(a) The maximum 'through fault' current up to which the protection scheme remains stable.
(b) Whether the switchgear is capable to handle maximum through fault current.
(c) The value of minimum internal fault current that can be detected by protection scheme.
(d) The pick-up setting for detecting minimum internal fault current of 90 Amp.
- Consider a signal detector with an input
$r = \pm A + n$
where $+A$ and $-A$ occur with equal probability and the noise variable $n$ is characterized by the Laplacian pdf shown.
[Figure]
Figure: Laplacian pdf $p(n) = \frac{1}{\sqrt{2}\sigma}e^{-|n|\frac{\sqrt{2}}{\sigma}}$, symmetric about 0 with a peak at $n = 0$.
(i) Determine the probability of error as a function of the parameters $A$ and $\sigma$.
(ii) Determine the SNR required to achieve an error probability of $10^{-6}$.
- A coil of 300 V moving iron voltmeter has a resistance of 500 ohms and an inductance of 0.8 H. The instrument reads correctly at 50 Hz AC supply and takes 100 mA at full scale deflection. What is the percentage error in the instrument reading, when it is connected to 200 V DC supply.
- (i) The configuration of a 400 KV 3 phase line is shown in figure. The radius of each sub-conductor is 2 cm. Calculate the charging mega volt-amperes if line is operating at 50 Hz and has a length of 300 km. [10]
[Figure]
Figure: three phases a, b, c each a two-conductor bundle (a, a'; b, b'; c, c'), bundle spacing 0.5 m, phase spacing 10 m.
(ii) Calculate the most economical overall diameter of insulation of a cable to be operated at 400 KV, 3 phase power system if maximum stress is limited to 100 KV/cm. [10]
- Derive the conditions of balance of an Anderson's bridge and also draw the phasor diagram of the bridge under balanced condition. Determine the unknown quantities in terms of known parameters and comment on easy convergence of balance of the bridge.
- The approximate magnitude plot, obtained experimentally, of a nonminimum phase system is shown in figure. Calculate the phase in degrees at $w = 3$ rad/sec.
[Figure]
Figure: magnitude (dB) versus $w$ (rad/sec): flat at 0 dB up to $w = 2$, then falling with a constant negative slope through $w = 20$ and beyond.
- Explain the ratio error and phase angle error of current transformer.
- The two top rows of a Routh table of a characteristic polynomial is given in the table. Determine the roots of the characteristic equation which lie in the left half $s$-plane. Complete the remaining rows of the table.
| $s^4$ | 1 | 10 | 24 |
|---|---|---|---|
| $s^3$ | 5 | 20 | |
- A pulse is applied to a piezo-electric transducer for a time $T$. Prove that in order to keep the undershoot of the response to a value within 5%, the value of time constant should be approximately $20T$.
- A discrete memoryless source (DMS) has five symbols $x_1, x_2, x_3, x_4$ and $x_5$ with $P(x_1) = 0{\cdot}4$, $P(x_2) = 0{\cdot}19$, $P(x_3) = 0{\cdot}16$, $P(x_4) = 0{\cdot}15$ and $P(x_5) = 0{\cdot}1$.
(i) Construct a Shannon Fano code for the source and calculate the efficiency of the code.
(ii) Repeat for Huffman code. Compare the results of (i) and (ii).
- List the functional classification of 8085 instruction set. Give one example for each class.
- A synchronous machine is connected to an infinite bus through a transformer and a double circuit line as shown in figure. The infinite bus voltage is $V = 1{\cdot}0\angle 0^\circ$ p.u. The direct axis transient reactance of the machine is $0{\cdot}20$ p.u., the transformer reactance is $0{\cdot}10$ p.u. and the reactance of each of the transmission lines is $0{\cdot}4$ p.u. all the values are to a base of the rating of the synchronous machine. Initially, the machine is delivering $0{\cdot}8$ p.u. power with a terminal voltage $|V_t| = 1{\cdot}05$ p.u. The inertia constant $H = 5$ MJ/MVA. All resistances are neglected. Determine the equation of motion of the machine rotor.
[Figure]
Figure: generator $E = |E|\angle\delta$, transformer T, two parallel lines Line-1 (breakers CB1, CB3) and Line-2 (breakers CB2, CB4) to infinite bus-bar $V = 1{\cdot}0\angle 0^\circ$ p.u.
- State Nyquist stability criterion. Is the feedback system shown in figure in open loop stable? Determine the closed loop stability of the system using Nyquist stability criterion. Show all the required plots clearly.
[Figure]
Figure: unity-sign negative feedback loop with forward block $\frac{1}{s(s+1)}$ and feedback block $2(s-2)$.
- Write advantages, disadvantages and application of spectrum analyzer.
- Discuss the percentage differential Relay with harmonic restraint with the help of diagram and also draw the conceptual representation of it.
- A sinusoidal voltage of 10 V amplitude at 100 Hz is applied to a lead network shown in figure. The phase difference between the input voltage $V_i(t)$ and output voltage $V_o(t)$ is $44{\cdot}43^\circ$. If $C = 0{\cdot}1\,\mu F$ and $R_1 = 100\,k\Omega$, determine the value of $R_2$ and the magnitude of steady state output voltage.
[Figure]
Figure: $C$ in parallel with $R_1$ in series path from $V_i(t)$ to $V_o(t)$, $R_2$ shunt across the output.
- Consider a connected graph $G = (N, A)$ with $N$ nodes and $A$ arcs, and a weight $\omega_{ij}$ for each arc $(i, j) \in A$.
(i) Define minimum weight spanning tree (MST).
(ii) If all arc weights of $G$ are distinct, prove that there exists a unique MST.
- (i) Prove that the minimum distance of any linear $(n, k)$ block code satisfies $d_{min} \le 1 + n - k$. [5]
(ii) Show that the minimum Hamming distance of a linear block code is equal to the minimum number of columns of its parity check matrix that are linearly dependent. From this conclude that the minimum Hamming distance of a Hamming code is always equal to 3. [15]
- A commercial interface unit uses different names for the handshake lines associated with the transfer of data from the I/O device into the interface unit. The interface input handshake line is labelled STB (strobe), and the interface output handshake line is labelled IBF (input buffer full). A low-level signal on STB loads data from the I/O bus into the interface data register. A high-level signal on IBF indicates that the data item has been accepted by the interface. IBF goes low after an I/O read signal from the CPU when it reads the content of the data register.
(i) Draw the block diagram showing the CPU, the interface, and the I/O device together with the pertinent interconnections among the three units.
(ii) Draw a timing diagram for the handshaking transfer.
(iii) Obtain a sequence of events flowchart for the transfer from the device to the interface and from the interface to the CPU.
- For a 3-bus power system, assume
Voltage at bus - 1 : $V_1 = (1{\cdot}05 + j0)$ pu,
Voltage at bus - 2 : $V_2 = (0{\cdot}9812 - j0{\cdot}0522)$ pu and
Voltage at bus - 3 : $V_3 = (0{\cdot}999 - j0{\cdot}0468)$ pu.
The line impedances are shown below:
| Bus code | Impedances (in p.u.) |
|---|---|
| 1 - 2 | $(0{\cdot}02 + j0{\cdot}04)$ |
| 1 - 3 | $(0{\cdot}01 + j0{\cdot}03)$ |
| 2 - 3 | $(0{\cdot}0125 + j0{\cdot}025)$ |
Compute Real and Reactive power loss in all the lines and also compute total system loss.