Mains PYQs
UPSC Mains Electrical Engineering paper 1 2021 questions
- In Figure 1(a) shown below, the two-port network is characterized in terms of y-parameters with $y_{11} = 3{\cdot}3 \times 10^{-3}\,\mathrm{S}$, $y_{22} = 5 \times 10^{-3}\,\mathrm{S}$ and $y_{12} = y_{21} = 0$. Find the voltage across $200\,\Omega$ load.
[Figure]
Figure 1(a): source $100\sin(2t)$ in series with 2 H inductor to port 1; $0.01$ F capacitor between 1' and 2'; $200\,\Omega$ load across port 2.
- For the signal shown in Figure 1(b), calculate the total energy of the signal $X(t)$. Also sketch $y(t) = X(10t - 5)$.
[Figure]
Figure 1(b): $X(t)$ rises from 0 at $t=-3$ to 1 at $t=-2$, stays 1 until $t=-1$, steps to 2 from $t=-1$ to $t=1$, steps down to 1 from $t=1$ to $t=2$, falls to 0 at $t=3$.
- A 220 V dc shunt motor has armature resistance $R_a = 0{\cdot}13\,\Omega$, field resistance $R_f = 250\,\Omega$ and rotational loss 230 W. On full-load, the line current is $9{\cdot}5$ A with the motor running at 1440 rpm. Determine the following:
(i) The mechanical power developed
(ii) The power output
(iii) The load torque
(iv) The full-load efficiency
- For the transistor circuit shown in Figure 1(d), determine the value of reverse saturation current, $I_S$, that would give a collector current of 1 mA, if $\beta = 80$, $V_A = \infty$ and $V_T = 26\,\mathrm{mV}$ at $T = 300\,\mathrm{K}$.
[Figure]
Figure 1(d): $V_{CC} = 2{\cdot}5\,\mathrm{V}$, PNP transistor $Q_1$ with a $20\,\mathrm{k}\Omega$ resistor from base to collector node, and a $1{\cdot}6\,\mathrm{k}\Omega$ resistor from collector to ground.
- Consider the four variables logic function defined as follows:
$F(A,B,C,D) = \bar{A}C + \bar{A}D + \bar{B}C + \bar{B}D + AB\bar{C}\bar{D}$
Assuming input variables as A, B, C and D, propose a logic circuit using only three logic gates to implement the function.
- Find the Thevenin's equivalent of the circuit shown in Figure 2(a) below as seen from the load impedance $Z_L$. Also find the value of $Z_L$ for maximum power transfer.
[Figure]
Figure 2(a): source $100\angle 0^\circ$, $-j2\,\Omega$ capacitor, coupled inductors $j4\,\Omega$ and $j9\,\Omega$ with $k = 0{\cdot}5$, $j2\,\Omega$ inductor, $2\,\Omega$ resistor and $j3\,\Omega$ inductor in the common branch, load $Z_L$.
- (i) Compute the convolution $X[n] * h[n]$, where
$X[n] = \left(\frac{1}{2}\right)^{-n} u[-n-2]$
$h[n] = u[n-2]$.
(ii) Consider the signal $X(t)$ shown in Figure 2(b)(ii) below. Represent the signal $X(t)$ in terms of rectangular pulse signal $V(t)$ shown in the same figure.
[Figure]
Figure 2(b)(ii): $X(t)$ is 1 for $0<t<1$, 2 for $1<t<2$, 3 for $2<t<3$, 2 for $3<t<4$, 0 elsewhere; $V(t)$ is a rectangular pulse of height 1 from $t=-1$ to $t=1$.
- Consider the circuit shown in Figure 2(c) below. Let inputs A, B and C be all initially LOW. Output Y is supposed to go HIGH only when A, B and C go HIGH in a certain sequence. Determine the sequence that will make Y go HIGH. Modify this circuit to use D-Flip-flops.
[Figure]
Figure 2(c): two JK flip-flops; first has J = A, CLK = B, K grounded, output X; second has J = X, CLK = C, K grounded, output Y; both CLR inputs tied to a Start pulse.
- (i) Explain what happens when a circuit shown in Figure 3a(i) below is constructed using logarithmic amplifier. [10]
[Figure]
Figure 3(a)(i): op-amp with $V_{REF}$ through $R_1$ to inverting input, transistor $Q_1$ in feedback, output $V_1$ drives base of $Q_2$ with collector current $I_X$.
(ii) Explain what happens if the topology is modified as shown in Figure 3(a)(ii) below. [10]
[Figure]
Figure 3(a)(ii): same, but $Q_2$ has its base connected to ground and its emitter/collector arrangement changed with $V_1$ connected to the other terminal, collector current $I_X$.
- For the circuit shown in Figure 3(b), calculate the voltage $V_0(t)$ as function of time,
[Figure]
Figure 3(b): source $V(t)$, $10\,\Omega$ resistor, $0{\cdot}1$ F capacitor with voltage $V_0$, current source $I(t)$, 4 H inductor and 20 V source.
where $V(t) = 10\sin(6t + 60^\circ)$ V and $I(t) = 5\cos(4t + 30^\circ)$ A.
- A mixer (analog multiplier) is used as a process in some analog communication systems. Two signals $X_1(t)$ and $X_2(t)$ are mixed to produce the output $y(t) = X_1(t)X_2(t)$.
If $X_1(t) = 10\,\mathrm{sinc}(10t)$ and $X_2(t) = 2\cos(1000\pi t)$, then calculate and plot the magnitude of the Fourier transform of output signal. Further, specify and prove the property of Fourier transform used in calculations.
- Consider a discrete time system with transfer function given by
$H(z) = \frac{Y(z)}{R(z)} = \frac{z^{-1} - \frac{1}{2}z^{-2}}{\left(1 - z^{-1} + \frac{2}{9}z^{-2}\right)}$.
Calculate the following:
(i) The impulse response of the system
(ii) The step response of the system with zero initial conditions
(iii) The step response of the system with initial conditions $y[-1] = 1$ and $y[-2] = 2$
- (i) Verify by determining the logic equation for the output and by constructing the truth table for the logic circuit shown in Figure 4(b).
(ii) Use an 8 to 1 multiplexer and logic gates to implement the following function:
$F(A,B,C,D,E) = \sum m(0, 1, 2, 4, 5, 6, 7, 13, 14, 20, 21, ..., 28, 29, 30, 31)$
[Figure]
Figure 4(b): four 2-to-1 multiplexers (inputs $D_0$ to $D_7$, select $S_0$) feed the 00, 01, 10, 11 inputs of a 4-to-1 multiplexer with selects $S_2$, $S_1$ and output Y.
- Determine the closed loop gain of the inverting amplifier shown in Figure 4(c) below. Explain the result if $R_1 \to 0$ or $R_3 \to 0$.
[Figure]
Figure 4(c): inverting amplifier with $V_{in}$ through $R_2$ to the inverting input, $R_3$ from the inverting input to node $V_x$, $R_4$ from $V_x$ to ground, $R_1$ from $V_x$ to output $V_{out}$, $A_0 = \infty$.
- A step down dc chopper is feeding a load of $R = 10\,\Omega$ and $L = 20\,\mathrm{mH}$. The dc supply voltage is 100 V. The chopper is switching at a frequency of 2 kHz with a duty cycle of 50%. Determine the load current and the peak-to-peak ripple current as an absolute value and as percentage of dc value.
- In a certain material with $\sigma = 0$, $\epsilon = \epsilon_0\epsilon_r$ and $\mu = \mu_0\mu_r$, the magnetic field intensity component is given by
$H = 10\sin(10^8 t - 2x)\,a_z\ \mathrm{A/m}$.
Find the following:
(i) Displacement current density
(ii) Electric field intensity
- A Scott connected transformer shown in Figure 5(c) is supplied from 11 kV, 3-phase, 50 Hz mains. Secondaries are series connected and supply 1100 A at a voltage of $100\sqrt{2}$ V to a resistive load. The phase sequence of the 3-phase supply is ABC.
(i) Calculate the turns ratio of the teaser transformer.
(ii) Calculate the line current $I_B$ and its phase angle with respect to the voltage of phase A to neutral on the 3-phase side.
[Figure]
Figure 5(c): teaser transformer with primary $\frac{\sqrt{3}}{2}N_1$ and secondary $N_2$, main transformer with primary $N_{1/2}$ + $N_{1/2}$ (tap M) across B and C and secondary $N_2$, secondaries in series feeding 1100 A at $100\sqrt{2}$ V to a resistive load.
- A transmitter with a 10 kW carrier transmits 11.2 kW when modulated with a single sine wave. Calculate the modulation index. If the carrier is simultaneously modulated with two other sine waves also at 50% modulation, calculate the total power transmitted.
- For the circuit shown in Figure 5(e), $v_C(0+) = 2$ V and $i(0+) = \frac{2}{3}$ A. Calculate the value of $v_C(t)$ for $t > 0$.
[Figure]
Figure 5(e): capacitor $C_1 = 0{\cdot}5$ F with voltage $v_C$, dependent current source $\frac{i}{2}$, $3\,\Omega$ resistor and capacitor $C_2 = \frac{1}{3}$ F carrying current $i$.
- The magnetic field intensity of a linearly polarized uniform plane wave propagating in the +Y-direction in sea water ($\epsilon_r = 80$, $\mu_r = 1$, $\sigma = 4\,\mathrm{S/m}$) is
$H = 0{\cdot}1\sin\left(10^{10}\pi t - \frac{\pi}{3}\right)a_x\ \mathrm{A/m}$.
At Y = 0, determine the following:
(i) The attenuation constant, intrinsic impedance, the wavelength and skin depth.
(ii) The location at which the amplitude of H is $0{\cdot}01$ A/m.
(iii) The expression for E(y, t) and H(y, t) at Y = 0.5 (m) as functions of t.
- A three-phase bridge inverter shown in Figure 6(b) is used to feed a Y-connected resistive load with $R = 10\,\Omega$ per phase. The dc input to the inverter $V_S = 400$ V and the output frequency is 50 Hz. If the inverter is operating with $180^\circ$ conduction mode,
(i) compute the rms value of the load current,
(ii) compute the rms value of the current in each switching device,
(iii) calculate the output power, and
(iv) draw the waveforms of phase and line voltages.
[Figure]
Figure 6(b): three-leg bridge with switches $Q_1$ to $Q_6$ and diodes $D_1$ to $D_6$, supply $V_S$, outputs a, b, c feeding a Y-connected load of three resistors R with neutral n.
- Let the measurement error of a physical quantity be defined by a random variable X and its density function as follows:
$f(x) = \begin{cases} K(3 - x^2) & -1 \le x \le 1 \\ 0 & \text{elsewhere} \end{cases}$
Determine the value of 'K' and find the probability that a random error in measurement is less than 1/2.
- The following test data are obtained for a three-phase, 195 MVA, 15 kV, 50 Hz star connected synchronous machine.
Open circuit test:
| $I_f$ (A) | 150 | 300 | 450 | 600 | 750 | 900 | 1200 |
|---|---|---|---|---|---|---|---|
| $V_{LL}$ (kV) | 3.75 | 7.5 | 11.2 | 13.6 | 15 | 15.8 | 16.5 |
Short circuit test:
$I_f = 750$ A, $I_a = 7000$ A
The armature resistance is small.
(i) Draw the open circuit characteristic, the short circuit characteristic, the airgap line and the modified airgap line.
(ii) Determine the unsaturated and saturated values of the synchronous reactance in pu.
(iii) Find the field current required, if the synchronous machine is to deliver 100 MVA at rated voltage, at 0.8 leading power factor.
- A three-phase, full-wave thyristor bridge converter is operated from a three-phase, Y-connected 220 V, 50 Hz supply and the load resistance is $20\,\Omega$.
It is required to obtain an average output voltage of 50% of the maximum possible output voltage. Determine the following:
(i) The delay angle $\alpha$
(ii) The rms and average output currents
(iii) The rms and average thyristor currents
(iv) The rectification efficiency
(v) The input PF
- A lossless transmission line has characteristic impedance $Z_0 = 50\,\Omega$. Its length is 30 m and operates at 5 MHz. The line is terminated with a load $Z_L = 60 + j50\,\Omega$. If the phase velocity $u = 0{\cdot}6c$ on the line, find the following:
(i) The reflection coefficient '$\Gamma$'
(ii) The standing wave ratio 'S'
(iii) The input impedance '$Z_{in}$'
- For an FM communication system with $\beta = 2$ and white channel noise with PSD $S_n(\omega) = 10^{-10}$, the output SNR is found to be 28 dB. The base band signal $m(t)$ is Gaussian, band-limited to 15 kHz, and $3\sigma$ loading is used.
Determine the following:
(i) The received signal power '$S_i$'
(ii) The output signal power '$S_o$'
(iii) The output noise power '$N_o$'
- A three-phase, 4-pole, 50 Hz induction motor has a rotor resistance of $4{\cdot}5\,\Omega$/phase and a standstill reactance of $8{\cdot}5\,\Omega$/phase with no external resistance in the rotor circuit. The starting torque of the motor is 85 Nm. Neglecting stator voltage drop, determine the following:
(i) The rotor voltage at standstill
(ii) The starting torque, if a $3\,\Omega$ resistance were added in each rotor phase
(iii) The rotor induced voltage and the torque at a slip of 0.03
- A 220 V, 1500 rpm, 10 A separately excited dc motor has an armature resistance of 1 ohm. It is fed from a single phase fully-controlled bridge rectifier with an ac source voltage of 230 V, 50 Hz. Assuming continuous load current, determine the following:
(i) Motor speed at the firing angle of $30^\circ$ and torque of 5 Nm
(ii) Developed torque at the firing angle of $45^\circ$ and speed of 1000 rpm