Mains PYQs
UPSC Mains Electrical Engineering paper 1 2020 questions
- The switch shown in Figure 1(a) has been closed for a very long time and it is opened at time $t = 0$.
(i) Find the value of $i_L$ for $t < 0$.
(ii) Just after the switch is opened, find the value of $i_L(0^+)$.
(iii) Determine the expression for $i_L(t)$ for $t > 0$ and find the value of $i_L(\infty)$.
[Figure] Circuit: 100 V source with 20 $\Omega$ resistor in series; switch ($t=0$) in series with 5 $\Omega$ and a second 100 V source (polarity opposite) in a parallel branch; 0.5 H inductor carrying current $i_L$.
- Sketch the continuous-time signal $x(t) = t\,[u(-t+1) - u(-t-1)]$ over a suitable range of $t$, where $u(t)$ is a unit step function.
- A 220 V, 8-pole lap wound dc shunt motor has 1200 conductors and has a field resistance of 220 $\Omega$. The motor takes a line current of 50 A at full load and rated speed. Find the additional resistance required in the field circuit if its speed is to be raised by 40 percent while maintaining its torque output at previous full load value. Assume linear magnetic circuit for the machine and resistance of each armature conductor as 50 m$\Omega$.
- A Darlington transistor pair circuit is shown in Figure 1(d) below. Both the transistors have dc current gain $\beta$ of 30. In the circuit $V_{CC} = +12\,\mathrm{V}$, $R_E = 1.5\,\mathrm{k\Omega}$.
(i) Find the value of $R_1$ needed to bias the circuit such that $V_{CEQ_2} = 5\,\mathrm{V}$ for transistor $T_2$.
(ii) With the same value of $R_1$ as obtained above, determine the value of $V_{CEQ_1}$.
Assume both $T_1$ and $T_2$ are Si transistors.
[Figure] Darlington pair: $R_1$ from $V_{CC}$ to base of $T_1$; collectors of $T_1$ and $T_2$ at $V_{CC}$; emitter of $T_1$ to base of $T_2$; $R_E$ from emitter of $T_2$ to ground.
- Implement the following Boolean functions with a $4 \times 3$ Programmable Logic Array (PLA):
$F_1 = \bar{B}\,\bar{C} + A\bar{B}$
$F_2 = AB\bar{C} + A\bar{B}C\bar{D}$
$F_3 = \bar{A}\,\bar{B}\,\bar{C}D + A\bar{B}CD$
- (i) Find the h-parameters of the two-port circuit shown in Figure 2(a)(i). If the input contains a source voltage with series resistance of 200 $\Omega$, find the output impedance ($Z_{out}$) of the circuit. [10]
[Figure] Two-port: 1 k$\Omega$ across port 1; dependent current source $10^{-5} V_2$; dependent voltage source $100 V_1$ in series with 10 k$\Omega$ at port 2.
(ii) In Figure 2(a)(ii)(A), the ideal switch S is switched on and off with a switching frequency $f = 10\,\mathrm{kHz}$. The circuit is operated in steady state at the boundary of continuous and discontinuous conduction, so that the inductor current $i$ is as shown in the Figure 2(a)(ii)(B). Find the values of on-time $T_{on}$ of the switch and peak current of inductor $I_p$. [10]
[Figure] (A) 100 V source, switch S, inductor 100 $\mu$H carrying $i$, diode, 500 V source. (B) Switch signal S with $T_{on}$ and $T_{off}$, and triangular inductor current $i$ with peak $I_p$ against $t$.
- The unit-impulse response of a linear time-invariant continuous-time system is given by $h(t) = [3e^{-3t} + 2t\,e^{-3t}]\,u(t)$.
Determine the system response $y(t)$ for an input $x(t) = 10e^{-3t}\,u(t)$, where $u(t)$ is a step function.
- Design a combinational circuit to implement the minimal sum-of-products of the logic function $F = \sum_{WXYZ}(1, 2, 3, 5, 7, 11, 13)$.
- Shown below (Figure 3(a)) is a differential amplifier with a three transistor active load. Draw the small signal equivalent circuit of its output stage with active load and calculate its small signal differential mode voltage gain.
Assume the output impedances of the transistors $Q_1$ to $Q_5$ to be $r_{01}$ to $r_{05}$ respectively.
Assume the base currents to be negligible.
[Figure] Differential pair $Q_1$, $Q_2$ with inputs $v_d/2$ and $-v_d/2$, tail current source $I_Q$ to $-V_{CC}$; active load $Q_3$, $Q_4$, $Q_5$ from $+V_{CC}$; currents $i_1 = i_2 = i_3 = i_4 = g_m v_d/2$ marked; output through $C_C$ to $R_L$, output $v_o$.
- (i) Let $\omega = 1000\,\mathrm{rad/sec}$ for the circuit of Figure 3(b)(i) and determine the value of the ratio $V_o/V_s$, if $L_1 = 1\,\mathrm{mH}$, $L_2 = 25\,\mathrm{mH}$ and $k = 1$. [10]
[Figure] Source $V_s$ in series with 2 $\Omega$ feeding coupled inductors $L_1$, $L_2$ (coupling $k$); secondary loaded with 40 $\Omega$, output voltage $V_o$ across it.
(ii) An electrical network is fed by two ac sources, as shown in Figure 3(b)(ii). Given that $Z_1 = (1 - j)\,\Omega$, $Z_2 = (1 + j)\,\Omega$ and $Z_L = (1 + j0)\,\Omega$. Find the values of Thevenin voltage and impedance across terminals X and Y. [10]
[Figure] $V_1 = 30\angle 45^\circ\,\mathrm{V}$ source, $Z_1$, node X, $Z_2$, $V_2 = 30\angle -45^\circ\,\mathrm{V}$ source; $Z_L$ between X and Y.
- Find the Z transform of a discrete sequence $x[n] = n\,(u[n] - u[n-4])$, where $u[n]$ is a unit step sequence.
- A continuous-time signal $x(t) = \cos(2\pi\, 400t)$ is sampled with a sampling frequency $f_s = 1600\,\mathrm{Hz}$. Obtain the 4-point DFT of the sampled sequence and plot the magnitude and phase spectrum.
- Design a synchronous sequential circuit with D-flip-flops for a state diagram shown in Figure 4(b).
[Figure] State diagram: 000 -> 001 -> 100 -> 111 -> 101 -> 000; 010 -> 000; 110 -> 101; 011 -> 100.
- A first order low pass filter circuit is shown in Figure 4(c) below. It is desired that the dc gain of the filter be 5 and the input impedance is 10 k$\Omega$. The value of the capacitor $C = 100\,\mathrm{nF}$. Find the values of $R$, $R_1$ and the cut-off frequency $f_c$ of the filter. (Assume ideal OP-AMP)
[Figure] Inverting op-amp: $V_i$ through $R_1$ to inverting input; feedback $R$ in parallel with $C = 100\,\mathrm{nF}$; output $V_o$.
- A separately excited dc motor is controlled by varying its armature voltage using a single-phase fully-controlled converter bridge as shown in Figure 5(a). The field current is kept constant at rated value. The motor has an armature resistance of 0.2 $\Omega$, and the motor voltage constant is 2.5 V/(rad/sec). The motor is driving a mechanical load having a constant torque of 140 Nm.
[Figure] 250 V rms, 50 Hz source feeding a single-phase thyristor bridge; armature with $R_a = 0.2\,\Omega$; field $\phi$ = constant.
For the firing angle of the converter being $60^\circ$ and assuming the armature current to be continuous and ripple free,
(i) calculate the motor armature constant.
(ii) evaluate the motor speed in rad/sec.
(iii) calculate the rms value of the fundamental component of the input current to the bridge converter.
- A parallel plate capacitor is made of circular discs of radius 0.1 m. The medium inside is air. The spacing between the two plates is 0.05 m. A voltage of $50\cos 10^4 t$ volts is applied between the two plates. Find the rms value of the displacement current flowing through the capacitor using Maxwell's equations.
Also show that the rms value of the total capacitor current calculated from voltage equation is same as the displacement current.
Assume permittivity of free space $\varepsilon_0 = \frac{1}{36\pi} \times 10^{-9}\,\mathrm{F/m}$.
- A three-phase 4-pole squirrel cage type induction motor develops maximum torque at 20 percent slip. The maximum to rated torque ratio of the motor is 2.8. If the input voltage fluctuates during its operation, find the minimum voltage as a percentage of full load voltage allowable to develop rated torque. Also find the developed torque as a percentage of full load torque at rated slip under this condition.
Assume standstill rotor resistance of 1.5 $\Omega$ per phase, negligible stator side impedance and linear magnetic circuit.
- Vestigial sideband modulated wave is to be generated by passing a double sideband suppressed carrier wave through a filter.
Show that the transfer function $H(f)$ of this filter must satisfy the condition $H(f - f_c) + H(f + f_c) = 2H(f_c)$, where $H(f_c)$ is constant.
Assume the message signal to be $m(t)$.
- Find the values of branch currents $I_a$, $I_b$ and $I_c$ as indicated in the circuit of Figure 5(e).
[Figure] Current source $10.6\angle 0^\circ$ A; 10 $\Omega$ resistor carrying $I_a$ across the source; 1 $\Omega$ (current $I_x$) and $j2\,\Omega$ in series; $-j5\,\Omega$ shunt carrying $I_c$; 5 $\Omega$ carrying $I_b$ in series with dependent voltage source $20 I_x$.
- Under what conditions do the attenuation constant $\alpha$ and the velocity of propagation $v$, for a distortionless transmission line, become independent of the frequency simultaneously? Why is it not practical to have such a transmission line?
- (i) Figure 6(b) shows a step-up dc-dc converter with ideal devices and elements. In its steady-state analysis the output filter capacitor is assumed to be very large to ensure a constant output voltage $v_o(t) \cong V_o$. The switch is turned on and off periodically with a frequency of $f_s$ and duty ratio of $D$. With the help of neat waveforms, find the expressions for peak-to-peak current ripple of inductor ($I_{L,\,\mathrm{peak}}$) and output voltage ripple ($\Delta V_o$) at steady-state in terms of circuit parameters and variables.
[Figure] Boost converter: $V_d$, inductor $L$ (voltage $V_L$), switch S, diode, capacitor $C$, load $R$ with output voltage $V_o$.
(ii) In a step-up dc-dc converter shown in Figure 6(b), $V_d = 12\,\mathrm{V}$, $V_o = 24\,\mathrm{V}$, $I_o = 0.5\,\mathrm{A}$, $L = 150\,\mu\mathrm{H}$, $C = 470\,\mu\mathrm{F}$, and $f_s = 20\,\mathrm{kHz}$. Calculate peak-to-peak output voltage ripple ($\Delta V_o$) and the rms value of the ripple in diode current (which also flows through the capacitor).
- Shown below is the frequency response of an ideal slope circuit.
[Figure] Plot of $H_1(f)/j$ against $f$: straight line of slope $2\pi a$ between $f_c - B_T/2$ and $f_c + B_T/2$, and the mirror image between $-f_c - B_T/2$ and $-f_c + B_T/2$.
How can it be used to demodulate an FM signal
$s(t) = A_c \cos\left[2\pi f_c t + 2\pi k_f \int_0^t m(t)\,dt\right]$
with a transmission bandwidth $B_T$, in combination with an envelope detector?
- A 220 V, 50 Hz, 3-phase star-connected salient pole alternator has six poles. With a field current of 2.4 A, it produces rated terminal voltage on open circuit condition. On short circuit, it requires 0.8 A field current to produce an armature current of 27.0 A. The alternator has $X_d$ to $X_q$ ratio of 1.5. It is connected to bus bars of 220 V line-to-line and its excitation required under this condition is 250 V.
(i) Find the maximum power that the alternator can deliver and the corresponding load angle with the excitation remaining unchanged.
(ii) Also find the maximum power that the alternator can deliver if a sudden loss of excitation occurs during the synchronised condition.
Assume linear magnetic circuit.
- Consider the frequency demodulation scheme shown in Figure 7(b) below :
[Figure] FM wave $s(t)$ goes to a delay line, whose output is subtracted from $s(t)$ in a summer; the sum goes to an envelope detector giving output signal $\alpha(t)$.
Here, the incoming FM wave $s(t)$ is passed through a delay line that produces a phase shift of $\frac{\pi}{2}$ radians at the carrier frequency $f_c$. The delay line output is subtracted from the incoming FM wave and the resulting composite wave is then envelope detected. Assuming that
$s(t) = A_c \cos\left[2\pi f_c t + \beta \sin(2\pi f_m t)\right]$
analyse the operation of this demodulator when the modulation index $\beta$ is less than unity and the delay $T$ produced by the delay line is sufficiently small to justify the approximation $\cos(2\pi f_m T) \approx 1$ and $\sin(2\pi f_m T) \approx 2\pi f_m T$.
- A uniform plane wave travelling in air is having an electric field of 50 V/m and is normally incident on an infinitely thick slab of dielectric constant 10. Find the electric and magnetic fields just inside the slab surface.
Also find the penetrated power inside the slab and the reflected electric and magnetic fields from the slab surface.
Assume $\mu_0 = 4\pi \times 10^{-7}\,\mathrm{H/m}$ and $\varepsilon_0 = \frac{1}{36\pi} \times 10^{-9}\,\mathrm{F/m}$.
- (i) An SCR having a turn ON time of 5 $\mu$ sec, latching current of 50 mA and holding current of 40 mA is triggered by a short duration pulse and is used in the circuit shown in Figure 8(a)(i). Find the minimum pulse width required to turn the SCR ON.
[Figure] 100 V source in series with SCR feeding a parallel combination of a 5 k$\Omega$ resistor and a branch of 20 $\Omega$ in series with 0.5 H.
(ii) A 3-phase, delta-connected, 6-pole, 50 Hz, 400 V, 925 rpm, squirrel cage induction motor has the following parameters :
$R_s = 0.2\,\Omega$, $R_r' = 0.3\,\Omega$, $X_s = 0.5\,\Omega$, $X_r' = 1\,\Omega$
The motor is fed from a voltage source inverter with constant V/f ratio below 50 Hz and constant voltage of 400 V above 50 Hz frequency. Calculate :
- Speed for the frequency of 35 Hz and half of full-load torque,
- Frequency for a speed of 600 rpm and 80% of full-load torque and
- Torque for a frequency of 35 Hz and speed of 650 rpm.
Assume motor speed - torque curves to be parallel straight lines in the region of interest.
- (i) Which type of probability density function is applicable in case of calculating errors with aiming of missiles/projectiles, if errors in each of the two rectangular coordinates have independent Gaussian probability density functions?
Find its mean, mean square value, variance and its cumulative distribution function.
(ii) Suppose an archer shoots at a target, 3 m in diameter for which the bull's eye is centered on the origin of an XY coordinate system. The position at which any arrow strikes the target is a random variable having an X-component and a Y-component. It is determined that the standard deviation of these components is $\frac{1}{6}$ m,
i.e. $\sigma_x = \sigma_y = \frac{1}{6}$
Assume that the X and Y components of the hit position are independent Gaussian random variables. What is the type of random variable that can be assigned to the distance of origin from the hit position (i.e. the miss distance)? Write its probability density function and find the mean value, its standard deviation and the probability that the target will be missed completely.
- A 150 KVA, 11 KV/415 V, 50 Hz single-phase transformer has maximum possible efficiency of 98.5% at 50 Hz, 125 KVA, 0.8 lag p.f. load. Its hysteresis and eddy current loss components are also same under this condition. Find the transformer efficiency at rated KVA and unity power factor load with its supply frequency changed to 40 Hz at unchanged input voltage.
Assume Steinmetz constant $x = 1.6$ for the transformer core.