Mains PYQs
UPSC Mains Electrical Engineering paper 2 2019 questions
- (i) In a binary PCM system, if the quantizing noise amplitude $N_q$ is not to exceed $P$ percent of the peak-to-peak analog level, show that the number of bits $n$ in each PCM word needs to be
$$n \geq \log_2 10\left[\log_{10}\left(\frac{50}{P}\right)\right] = 3.32\,\log_{10}\left(\frac{50}{P}\right)$$ [5]
(ii) A 700 Mbyte CD is used to store PCM data. Suppose a voice frequency (VF) signal is sampled at 8000 samples per second and the encoded PCM signal is to have an average SNR of at least 40 dB. How many minutes of VF conversation can be stored on the hard disc? [5]
- An 11 kV single-core cable has a conductor radius of 8.8 mm and an insulation thickness of 4.6 mm. Find the maximum and minimum electric stress.
- Explain the gain margin and phase margin of a control system for Nyquist stability criterion. Derive expressions for the centre and radius of a constant magnitude loci ($M$-circles) of a unity feedback control system and draw circles for $M$ = 0.5, 1.0, 1.2, 1.6, 2.0 and 3.0 on the graph paper with suitable scales and explanations.
- (i) Due to some errors in the internal circuit of a differential amplifier, its differential mode gain is halved, while its common-mode gain does not change. Find the reduction in the CMRR of this amplifier in decibels. [5]
(ii) A full-wave rectifier type ammeter displays a current reading of 5.55 mA r.m.s. when measuring the current waveform shown in the figure given below : [5]
[Figure] Triangular current waveform $i$ vs $t$ with peak $I_{max}$, swinging symmetrically positive and negative
Determine the true r.m.s. value of the current waveform and the error in the meter.
- Explain the function of the following signals in 8085 microprocessor :
(i) ALE
(ii) $\overline{\mathrm{RD}}$
(iii) $\overline{\mathrm{WR}}$
(iv) $\mathrm{IO}/\overline{\mathrm{M}}$
- A system consists of two plants connected by a transmission line and a load that is located at plant 2. Data for the loss equation consists of the information that 100 MW transmitted from plant 1 to the load results in a loss of 10 MW. Find the required generation from each plant and power received by the load when $\lambda$ for the system is ₹2.5 per megawatt-hour. Assume that the incremental fuel costs can be given by the following equations :
$$\frac{dF_1}{dP_1} = 0.003\,P_1 + 1.7\ \text{₹/MWh}$$
$$\frac{dF_2}{dP_2} = 0.006\,P_2 + 1.9\ \text{₹/MWh}$$
- Design an output port with address FFH to interface the 1408 D/A converter that is calibrated for a 0 to 10 V range (with the use of 8085 microprocessor). Write a program to generate a continuous ramp waveform. The pin diagrams of an octal latch (74LS373) and the 1408 D/A converter are provided for reference :
[Figure] Pin diagram of 74LS373 octal latch: pins 1 to 10 are $\overline{\mathrm{OE}}$, 1Q, 1D, 2D, 2Q, 3Q, 3D, 4D, 4Q, GND; pins 11 to 20 are LE, 5Q, 5D, 6D, 6Q, 7Q, 7D, 8D, 8Q, $V_{cc}$
[Figure] Pin diagram of 1408 D/A converter: pins 1 to 8 are Output range control, GND, $V_{EE}$, Current o/p, A1 (MSB), A2, A3, A4; pins 9 to 16 are A5, A6, A7, A8, $V_{cc}$, $+V_{ref}$, $-V_{ref}$, Compensation
- With the help of suitable circuit diagram and related equations, explain the principle of measurement of the unknown parameters of a low-impedance coil using a $Q$ meter in series connection mode.
- (i) Sketch a block diagram for a differential encoding and decoding system. Explain the working of the system by showing the encoding and decoding of the sequence 101100011001. Assume that the reference digit is a binary 1. Show that error propagation cannot occur with this arrangement. [6]
(ii) Consider a continuous input signal whose amplitude $m$ lies in the range $(-m_{max}, +m_{max})$. This is applied to a uniform quantizer of mid-rise type where the step size is given by $\Delta = \frac{2 \cdot m_{max}}{L}$, where $L$ denotes the number of representation levels. Let $\sigma_Q^2$ represent the variance of the quantization error and $R$ represent the number of bits per sample. Show that $\sigma_Q^2 = \frac{\Delta^2}{12}$. Using this result, show that $\sigma_Q^2 = \frac{1}{3} m_{max}^2 \cdot 2^{-2R}$ and that the output signal to noise ratio of a uniform quantizer is
$$(\mathrm{SNR})_o = \left(\frac{3P}{m_{max}^2}\right) \cdot 2^{-2R}$$ [8]
(iii) Consider a sine wave of frequency $f_m$ and amplitude $A_m$, that is applied to a delta modulator of step size $\Delta$. Derive the condition which, if satisfied, leads to the occurrence of slope overload error. [6]
- Sketch the root locus from the open-loop transfer function
$$G(s)H(s) = \frac{K}{s(s+6)(s^2+4s+13)}$$
and determine the following :
(i) The angles of departure from complex poles
(ii) The break-away points
(iii) The intersection with imaginary axis
(iv) The stability conditions
- Describe briefly various kinds of DC links used in HVDC transmission.
- (i) Find the transfer function $X(s)/E(s)$ for the electromechanical system shown in the following figure. Consider (1) the force acting on mass $P(t) = K_2 i_2(t)$ and (2) the back e.m.f. of coil $e_b(t) = K_1 \frac{dx(t)}{dt}$, where $K_1$ and $K_2$ are constants. [10]
[Figure] Electrical loop with source $e(t)$, $R$, $L$, mesh currents $i_1(t)$ and $i_2(t)$, capacitor $C$, coil with back e.m.f. $e_b(t)$ exerting force $P(t)$ on mass $M$ with spring $K$ and damper $D$, displacement $x(t)$
(ii) The block diagram representation of a control system is shown below : [10]
[Figure] Two-input two-output block diagram: inputs $R_1$, $R_2$, outputs $C_1$, $C_2$, forward blocks $G_1$, $G_2$, cross blocks $G_3$, $G_4$, feedback blocks $H_1$, $H_2$
Find $\frac{C_2}{R_1}$ transfer function using the following :
(1) Block diagram reduction method
(2) Mason's gain formula
- The figure given below shows percentage differential relay applied to the protection of an alternator winding. The relay has 0.1 ampere minimum pick-up and 10% slope of characteristic $(I_1 - I_2)$ vs $(I_1 + I_2)/2$. A high-resistance ground fault occurred near the grounded neutral end of generator winding, while the generator is carrying load. As a consequence, the currents in ampere flowing at each end of the winding are shown in the figure. Assume CT ratio of 400/5. Will the relay operate to trip the breaker?
[Figure] Generator winding with a CT (400/5) at each end, grounded neutral; currents $304+j0$ and $320+j0$; operating coil O and restraining coil R of the relay
- Draw the circuit diagram of an instrumentation amplifier and derive an expression for the voltage gain of this amplifier. How can this gain be varied?
- For a 3-$\phi$, 50 Hz, 132 kV system, the reactance and capacitance up to the location of the circuit breaker are 3 $\Omega$ and 0.015 $\mu$F respectively. Calculate the following :
(i) The frequency of transient oscillation
(ii) The maximum value of restriking voltage across the contacts of the circuit breaker
(iii) The maximum value of rate of rise of restriking voltage (RRRV)
- One conductor of a three-phase line is open. The current flowing to the $\Delta$-connected load through line $a$ is 10 A.
[Figure] Delta-connected load with impedances Z; line currents $I_a = 10\angle 0^\circ$ A, $I_b = 10\angle 180^\circ$ A, $I_c = 0$
With the current in line $a$ as reference and assuming that line $c$ is open, find the symmetrical components of the line currents.
- Four signals $s_1(t)$, $s_2(t)$, $s_3(t)$ and $s_4(t)$ are shown in the figure below. Find an orthonormal basis for this set of signals by making use of the Gram-Schmidt orthogonalization procedure. Draw the corresponding signal space diagram :
[Figure] $s_1(t)$ = 1.0 for 0 to $T/3$; $s_2(t)$ = 1.0 for 0 to $2T/3$; $s_3(t)$ = 1.0 for $T/3$ to $T$; $s_4(t)$ = 1.0 for 0 to $T$
- Write an assembly language program using the instruction set of 8085 microprocessor for addition of six bytes of data stored in memory locations starting at 2050H. The carry generated (if any) must be saved in register B. The entire sum must be stored at two memory locations 2070H and 2071H.
- A unity feedback control system is characterized by the open-loop transfer function
$$G(s) = \frac{K(s+13)}{s(s+3)(s+7)}$$
(i) Using the R-H criterion, calculate the range of values of $K$ for the system to be stable.
(ii) Check whether for $K = 1$, all these roots of the characteristic equation of the above system have damping factor greater than 0.5.
- A three-phase generator delivers 1.0 p.u. power to an infinite bus through a transmission network when a fault occurs. The maximum power which can be transferred in pre-fault, during fault and post-fault conditions are 1.75 p.u., 0.4 p.u. and 1.25 p.u. respectively. Find the critical clearing angle.
- (i) Consider an ON-OFF keying version of a binary ASK system, where symbol 1 (hypothesis $H_1$) is denoted by transmitting a DC level of amplitude $A$ and symbol 0 (hypothesis $H_0$) is denoted by not communicating any signal over the channel. Assume that symbols 0 and 1 occur with equal probability. The channel is perturbed by Additive White Gaussian Noise (AWGN) with zero mean and variance $\sigma^2$. Show that the average probability of error for this ASK system is
$$P_e = Q\left[\frac{A}{2\sigma}\right], \text{ where } Q(\alpha) \triangleq \frac{1}{\sqrt{2\pi}}\int_\alpha^\infty e^{-u^2/2}du$$ [10]
(ii) Consider a phase-locked loop (PLL) consisting of a multiplier, loop filter and voltage-controlled oscillator (VCO). Let the signal applied to the multiplier input be defined as $s(t) = A_c \cos[2\pi f_c t + k_p \cdot m(t)]$, where $k_p$ is the phase sensitivity and data signal is having value +1 for binary symbol 1 and -1 for binary symbol 0. The VCO output is $r(t) = A_v \sin[2\pi f_c t + \theta(t)]$. Evaluate the loop filter output, assuming that the filter removes the modulated components with frequency $2f_c$. Show that the loop filter output is proportional to the data signal $m(t)$, when the loop is phase-locked, that is, $\theta(t) = 0$. Illustrate your answer with a neat sketch. [10]
- What is the format of the control word of 8255 programmable peripheral interface? Explain the significance of each bit of the control word.
- The overall transfer function of a control system is given by
$$\frac{C(s)}{R(s)} = \frac{16}{s^2 + 1.6s + 16}$$
It is desired that the damping ratio be 0.8. Determine the derivative rate of feedback constant $K_d$, and compare rise time, peak time, maximum overshoot and steady-state error for unit ramp input without and with derivative feedback control.
- With the help of a suitable diagram and equations, describe the principle of operation of a differential capacitive displacement transducer. In what way is it better than a normal capacitive displacement transducer? Determine the output voltage of this differential transducer when it is connected in an AC bridge.
- Consider a discrete memoryless source, whose output can be modeled as a discrete random variable $S$ taking on symbols from a fixed alphabet $\zeta = \{s_0, s_1, ..., s_{K-1}\}$ with probabilities $P(S = s_k) = p_k$; $k = 0, 1, 2, ..., K-1$. Further $\sum_{k=0}^{K-1} p_k = 1$. Assume that the symbols emitted by the source during successive signaling intervals are statistically independent. Show that the entropy $H(\zeta)$ of such a source is bounded by
$$0 \leq H(\zeta) \leq \log_2 K$$
where $K$ represents the number of symbols of the source alphabet.
- (i) A memoryless source $S$ emits 6 message symbols with probabilities 0.3, 0.25, 0.15, 0.12, 0.1 and 0.08. Determine a 4-ary (quaternary) Huffman code for this source. Determine the average word length, the entropy and the efficiency of this Huffman code. [6]
(ii) The generator matrix of a (7, 4) linear block code is given by
$$\mathbf{G} = \begin{bmatrix} 1 & 1 & 0 & 1 & 0 & 0 & 0 \\ 0 & 1 & 1 & 0 & 1 & 0 & 0 \\ 1 & 1 & 1 & 0 & 0 & 1 & 0 \\ 1 & 0 & 1 & 0 & 0 & 0 & 1 \end{bmatrix}$$
where the first three columns form $\mathbf{P}$ and the last four form $\mathbf{I}_k$.
(1) Determine a parity check matrix $\mathbf{H}$ for this code.
(2) Show that $\mathbf{G} \cdot \mathbf{H}^T = 0$.
(3) Determine all right code words of the dual code.
(4) Find the minimum distance of the dual code. [8]
(iii) The figure shows the encoder for a rate $R = \frac{1}{2}$, constraint length $K = 4$ convolutional code. Determine the encoder output produced by the message sequence $u = 1011$. [6]
[Figure] Convolutional encoder: input feeding a chain of three flip-flops, two mod-2 adders fed from the input and flip-flop taps, output switch alternating between the two adder outputs
- (i) Explain the gain margin and phase margin of a control system for asymptotic Bode plot. The open-loop transfer function of a system is given by
$$G(s)H(s) = \frac{30}{s(0.5s+1)(0.08s+1)}$$
Draw the Bode plot and determine the following :
(1) The gain margin
(2) The phase margin
(3) The stability [10]
(ii) Sketch the Bode plot and determine the values of gain $K$ for the open-loop transfer function
$$G(s)H(s) = \frac{K}{s(s+1)(0.1s+1)}$$
so that-
(1) the gain margin is 15 dB;
(2) the phase margin is $60^\circ$. [10]
- The primitive impedance matrix of a power system network is given below :
| e \ e | 1 | 2 | 3 | 4 | 5 |
|---|---|---|---|---|---|
| 1 | 0.6 | 0.1 | 0 | 0.2 | 0 |
| 2 | 0.1 | 0.5 | 0 | 0 | 0 |
| 3 | 0 | 0 | 0.5 | 0 | 0 |
| 4 | 0.2 | 0 | 0 | 0.4 | 0 |
| 5 | 0 | 0 | 0 | 0 | 0.2 |
Find its primitive admittance matrix.