Mains PYQs
UPSC Mains Electrical Engineering paper 1 2019 questions
- In the network shown in Figure 1(a), determine the following :
(i) The value of the load resistance to have maximum power transfer
(ii) The maximum power delivered to the load
[Figure] 5 V source; R1 = 3 $\Omega$; R2 = 3 $\Omega$; R3 = 4 $\Omega$; variable load R_L between terminals a and b
- Two extensive homogeneous isotropic dielectrics meet on a plane at z = 0. For z > 0, $\varepsilon_{r1} = 4$ and for z < 0, $\varepsilon_{r2} = 3$. A uniform electric field $\vec{E}_1 = 5\,\hat{a}_x - 2\,\hat{a}_y + 3\,\hat{a}_z$ kV/m exists for z $\geq$ 0.
Find :
(i) $\vec{E}_2$ for z $\leq$ 0
(ii) The energy densities (in J/m$^3$) in both dielectrics
- Find the DC input resistance at the transistor base of the circuit shown in Figure 1(c).
[Figure] Transistor with supply +V_CC, collector resistor R_C, emitter resistor R_E to ground, base current I_in, input V_in, V_BE, $\beta_{DC}$
- A 15 kW, 230 V, 3-phase, Y-connected, 50 Hz, 4-pole squirrel cage induction motor has a starting torque of 115 percent and a maximum torque of 187 percent of its rated load torque. Neglecting the effects of stator resistance and rotational losses and assuming constant rotor resistance, find the slip and speed at maximum torque. Assume proper data, if required, with proper justification.
- A Type-A chopper circuit shown in Figure 1(e) below supplies a motor load from a DC source. Determine the value of maximum average current of the switch SW for constant load current operation of motor.
[Figure] DC source V_dc, switch SW, freewheeling diode D, DC motor modelled by R_a, L_a and back emf E_b
- Determine the expressions of currents $i_1$ and $i_2$ in time domain for the circuit shown in Figure 2(a).
[Figure] Source $10\cos^3 10t$ V, 5 $\Omega$ resistor carrying $i_1$, 6 mH inductor, 500 $\mu$F capacitor carrying $i_2$, dependent voltage source $3 i_1$
- A lossless line has a characteristic impedance of 50 $\Omega$ and is terminated in a load resistance of 75 $\Omega$. The line is energized by a generator which has an output impedance of 50 $\Omega$ and an open circuit output voltage of 30 $\mathrm{V_{rms}}$. The line is assumed to be 2.25 wavelength long.
Determine :
(i) The output impedance
(ii) The magnitude of the instantaneous load
(iii) The instantaneous power delivered to the load
- Determine the output voltage of the op-amp differentiator circuit shown in Figure 2(c) for the triangular wave input as shown and draw the output voltage waveform.
[Figure] Triangular input wave between -10 V and +10 V with half period 10 $\mu$s (period 20 $\mu$s); differentiator with 0.001 $\mu$F input capacitor and $R_f$ = 2.2 k$\Omega$
- Explain the operation of a two-phase induction motor under unbalanced operation with the help of relevant equivalent circuit models and phasor diagram.
If the applied stator voltages to this motor are $\hat{V}_\alpha$ and $\hat{V}_\beta$ (in time quadrature but unequal in magnitude), prove that the starting torque of this motor is same as that devoloped when balanced two-phase voltage of magnitude $\sqrt{V_\alpha V_\beta}$ is applied.
- For a series inverter shown below, the time interval between the instant Thyristor $T_1$ is turned OFF and the instant Thyristor $T_2$ is turned ON is $T_{off}$ seconds; where $T_{off} > t_{q\text{-}min}$ (minimum turn-off time of Thyristor $T_1$). Draw steady state waveforms of $i_{g1}$, $i_{g2}$ (gate currents of Thyristor $T_1$ and $T_2$ respectively), capacitor voltage $V_C$, inductor voltage $V_L$, load current $i_{Load}$ and supply current $i_s$. Analyse and identify in waveform drawn, different modes of circuit operations; namely Mode-1, Mode-2 and Mode-3. Analysis may be accompanied by relevant equations and their derivation.
[Figure] Series inverter: source V_DC, thyristors T1 and T2 with gate currents $I_{g1}$, $I_{g2}$, capacitor C (voltage $V_C$), inductor L (voltage $V_L$), load R carrying $i_{Load}$, supply current $i_s$
- Determine and sketch the convolution of the two signals given below :
$$x(t) = \begin{cases} 2, & -1 \leq t \leq 1 \\ 1, & 1 < t \leq 3 \\ 0, & \text{elsewhere} \end{cases}$$
and $h(t) = 2\,\delta(t+1) + \delta(t+2)$
- For the circuit shown in Figure 3(c), derive the expression for stability factor $S(\beta)$.
[Figure] Transistor with +V_CC, collector resistor R_C, and base resistor R_B connected from collector to base
- An angle modulated signal with carrier $\omega_c = 2\pi \times 10^5$ is described by the following equation :
$$\phi_{EM}(t) = 10\cos(\omega_c t + 5\sin 3000\,t + 10\sin 2000\pi t)$$
Find :
(i) Power of the modulated signal
(ii) Frequency deviation $\Delta f$
(iii) Deviation ratio $\beta$
(iv) Phase deviation $\Delta\phi$
(v) Also estimate the bandwidth of $\phi_{EM}(t)$.
- An FM signal has a frequency deviation of 5 kHz and a modulation frequency of 1 kHz. The signal to noise ratio at the input to the receiver detector is 20 dB. Calculate the approximate signal to noise ratio at the detector output. Assume that the detector is completely unresponsive to the amplitude variations, and it does not add noise of its own. Also, calculate the improvement in signal to noise ratio in the detector.
- A DC shunt generator running at rated speed of 1000 rpm can supply a full load current of 120 A at a nominal voltage of 105 V DC. The no load (open loop) characteristics at rated speed and nominal voltage is given below :
| Field Current, A | 1 | 2 | 3 | 4 | 5 | 6 | 7 |
|---|---|---|---|---|---|---|---|
| Generated Voltage, V | 36 | 66 | 86 | 100 | 110 | 118 | 123 |
Graphically determine the field resistance of shunt generator for its operation at nominal voltage at rated speed as a ratio of its critical field resistance.
If the total fixed losses (rotational and iron) are 600 W; find the value of maximum efficiency of the generator; given that the generator operates at 85% efficiency in nominal conditions.
- (i) A two-dimensional electric field is given by $\vec{E} = x^2\,\hat{a}_x + x\,\hat{a}_y$ V/m. Show that this electric field cannot arise from a static distribution of charge.
(ii) A transmission line of length 5 m is tested at a frequency of 20 MHz. When the far end of the line is short circuited, the impedance measured at the sending end is 4.61 $\Omega$ and when the far end is open circuited, the impedance becomes 1390 $\Omega$. Calculate the characteristic impedance and propagation constant of the line.
- Find the Laplace transform of the following signals :
(i) $x_1(t) = e^{-at}\cos(\omega_0 t)\,u(t)$
(ii) $x_2(t) = e^{-at}\sin(\omega_0 t)\,u(t)$
- Simplify the following expression using Boolean algebra :
$Y = AC + A(B + C) + C(B + C)$
and draw the logic diagram for reduced expression.
- Assuming that X is a Gaussian random variable with m = 0 and $\sigma$ = 1, find the probability density function of the random variable Y given by
$Y = aX + b$.
- Determine current i(t) in the circuit of Figure 5(d), for all values of time.
[Figure] 100 V battery in series with a 100u(t) V source and a 5 $\Omega$ resistor, feeding a parallel branch of 5 $\Omega$ resistor and a 10 H inductor carrying i(t)
- Determine ripple factor of output voltage ($V_o$), rectifier efficiency ($\eta$) and transformer utilization factor (TUF) for a single-phase half-wave controlled rectifier circuit fed from a source $V_s = 220\sin 314\,t$ to a load R = 10 $\Omega$. Assume firing angle $\alpha = \pi/4$ and transformer to be lossless.
[Figure] 220/12 V transformer, thyristor with firing angle $\alpha = \pi/4$ feeding load R = 10 $\Omega$
- An aeroplane flies over the surface of the ocean for which $\sigma$ = 4 S/m, $\varepsilon_r$ = 81 and $\mu_r$ = 1. The aeroplane transmits the signal in the form of 1 MHz plane wave having an electric field intensity of 1000 V/m and propagating vertically downward. If a submarine requires a minimum signal of 20 $\mu$V/m for adequate reception, determine the maximum communication depth of the submarine.
- A balanced three-phase supply system with a line voltage of 400 V is supplying a balanced Y-connected load with 1500 W at a leading power factor of 0.8. Determine the line current and the per phase load impedance. Now, a balanced 900 W lighting load is added in parallel to the system. What will be the new line current ?
- Implement Astable Multivibrator using NAND gates and explain its operation.
- For the circuit given in Figure 6(d), comment on its operating conditions.
[Figure] Transistor amplifier with $V_{CC} = -30$ V, $R_b$ = 10 k$\Omega$ (base current $I_B$), $R_c$ = 15 $\Omega$ with transformer coupled load $R_L$, $R_e$ = 5 $\Omega$ with bypass capacitor $C_e$, input coupling capacitor C, source $V_s$ with $R_s$
For the transistor, $\beta$ = 100
$I_{CO}$ = 1 mA
(at $V_{CB}$ = 40 V)
- An LTI system is characterised by the following difference equation :
$$y(n) - \frac{3}{4}y(n-1) + \frac{1}{8}y(n-2) = 2x(n)$$
(i) Find the impulse response of the system, if the input to the system is $x(n) = \left(\frac{1}{4}\right)^n u(n)$.
(ii) Find the frequency response of the output $y(j\omega)$, and $y(n)$.
- Determine $I_D$ and $V_{GS}$ for the JFET with voltage divider bias as shown in Figure 7(b). The internal parameter values of this JFET are such that $V_D \approx 7$ V.
[Figure] JFET with $V_{DD}$ = +12 V, $R_1$ = 6.8 M$\Omega$, $R_2$ = 1.0 M$\Omega$, $R_D$ = 3.3 k$\Omega$, $R_S$ = 2.2 k$\Omega$, drain current $I_D$, drain voltage $V_D$
- Show that the locus of the tip of the armature current phasor is a circle for a synchronous machine (Generator/Motor) operating at a constant terminal voltage $V_t$ and a constant excitation voltage $E_{af}$ with a fixed synchronous reactance $X_s$. Draw the phasor diagram and show the circular locus of $I_a$.
- Reduce the combinational logic circuit shown in Figure 7(d) to a minimum form.
[Figure] Inputs A, B, C each inverted and fed to an AND gate, its output inverted and fed to an OR gate along with a second gate whose inputs include D; output X
- Draw the block diagram of a single slope type A/D converter and explain its principle of operation.
- A 3-stage amplifier has stages with the following specifications :
| Stage | Power Gain | Noise Figure |
|---|---|---|
| 1 | 10 | 2 |
| 2 | 25 | 4 |
| 3 | 30 | 5 |
Calculate the overall power gain and noise figure in dB and the noise temperature. Assume matched conditions.
- A magnetic circuit shown below consists of two sections of Al-ni-co-5 of length $l_m$ = 1.0 cm embedded in a core of high permeability ($\mu \to \infty$). The cross-sectional areas of core, Al-ni-co-5 and air-gap are equal. The air-gap length 'g' = 0.2 cm has neglible fringing effect.
[Figure] Core with two Al-ni-co-5 sections each of length $l_m$ and area $A_m$, air gap g with $\mu_o$, $A_g$; $A_m = A_g$ = 40 cm$^2$; $\mu_o = 4\pi \times 10^{-7}$
If Al-ni-co-5 material B-H curve in second quadrant is linearly approximated, it can be given as below.
[Figure] Linear B-H curve: B (T) vs H (kA/m); linear from $H_C$ = -50 kA/m at B = 0 to (-40, 1.0), then linear to (0, about 1.2); marks at B = 0.5 and 1.0, H = -50, -40, -30, -20, -10, 0
Determine the slope of load line for the problem and hence determine the value of flux density ($B_g$) in the air-gap.
- Find the Z-transform of the signal $g(n) = |n|\,a^{|n|}$. Also find the ROC.