Mains PYQs
UPSC Mains Electrical Engineering paper 1 2018 questions
- Derive the expression of total average power in three-phase balanced circuit.
- Find the Laplace transform of the periodic function f(t) shown in Figure 1(b).
[Figure]
Figure 1(b): periodic sawtooth f(t), rising linearly from 0 to 2 over each interval 0 to 1, 2 to 3, 4 to 5, and zero between (1 to 2, 3 to 4), vertical drop at t = 1, 3, 5.
- (i) Draw thyristor gate characteristics and state its application in design of gate drive circuit.
(ii) A thyristor has a maximum average gate power dissipation limit of 0.4 watts. It is triggered with pulsed gate current of frequency 20 kHz at a duty ratio of 0.5. If the gate cathode voltage drop is 1 volt, find permissible peak gate current magnitude.
- For the op-amp circuit shown in Figure 1(d), determine the gain $A_v = \frac{v_o}{v_i}$. Assume that all resistors are equal.
[Figure]
Figure 1(d): inverting op-amp, input $v_i$ through R (current i) to the inverting terminal; feedback from output through a T network: R in series, R in series, with a shunt R to ground at each of the two intermediate nodes; non-inverting terminal grounded.
- A squirrel cage induction motor has a starting current of six times the full load current, at a slip of 0.04. Calculate the line current and starting torque in p.u. (per unit) of full load values for the following starting methods :
(i) Direct switching
(ii) Star-Delta starting
- Convert the following logic equation to NAND logic and draw the circuit using NAND gates :
$Z = (\overline{A+B})\,C + A\,(\overline{B+C})$
- (i) A low loss transmission line has characteristic impedance $Z_0 = 70\,\Omega$ and is terminated by another impedance of $115 - j80\,\Omega$. The wavelength on the line is 2.5 m.
Find :
I. SWR (Standing Wave Ratio)
II. Maximum and minimum line impedance, $Z_{1max}$ and $Z_{1min}$ [10]
(ii) If the input impedances of a short and open circuited transmission line of length 1.5 m are $Z_{SC} = -j78\,\Omega$ and $Z_{OC} = j90\,\Omega$ respectively, determine the characteristic impedance $Z_0$ and propagation constant $\gamma$ of the line. [10]
- An SSB transmitter transmits with 10 kW power. This transmitter is to be replaced by a standard amplitude modulated signal with same total power content. Determine the carrier power and each sideband power, when the percentage modulation is 80%.
- The maximum efficiency of a 50 KVA transformer is 97.4% and occurs at 90% of full load, at unity power factor. Calculate the efficiency at
(i) Full load at 0.8 power factor (p.f.)
(ii) Half the full load at 0.9 power factor (p.f.)
- A full bridge or H-bridge inverter has a switching sequence which results in a square wave output voltage. Let the switching frequency be 50 Hz and inverter is supplying a RL load having $R = 10\,\Omega$ and $L = 30\,\mathrm{mH}$. Determine :
(i) An expression for load current
(ii) The power absorbed by load
(iii) The average current in the D.C. source
(iv) The area in output voltage waveform where antiparallel diodes across switches conduct
(Assume Input D.C. voltage = 100 V)
- In the circuit shown in Figure 3(c), find the voltage $v_o$ across the $8\,\Omega$ resistor.
[Figure]
Figure 3(c): $4\,\Omega$ resistor on the left branch, 3 A current source (arrow pointing down), $2\,\Omega$ resistor on top, $3\,\Omega$ resistor on top right, $8\,\Omega$ resistor with $v_o$ (+ at top), 12 V battery on the right branch.
- The antenna current of a transmitter is 11.5 amperes, when it is modulated to a depth of 45% by an audio wave. The current enhances to 12.5 amperes on account of simultaneous modulation by another audio sine wave. Find the modulation index of the second audio wave.
- A 400 volts D.C. shunt motor draws 30 amperes while supplying the rated load at a speed of 120 rad/sec. The armature resistance is 1.0 ohm and the field winding resistance is 250 ohms. Determine the external resistance that must be inserted in series with armature circuit so that, the armature current should not exceed 150% of its rated value, when the motor is plugged. Find the braking torque, at the instant of plugging.
- The integrator circuit shown in Figure 4(c) is to be used to generate a triangular waveform from a 500 Hz square wave connected to its input. Suppose that the square wave alternates between $\pm 12\,\mathrm{V}$.
(i) Find the minimum slew rate required for the amplifier.
(ii) Find the maximum output voltage the amplifier can generate.
[Figure]
Figure 4(c): square wave input through $400\,\Omega$ to the inverting terminal; feedback from output through $1\,\mu\mathrm{F}$ capacitor in parallel with $4.7\,\mathrm{k\Omega}$ resistor; non-inverting terminal to ground through $370\,\Omega$.
- Convert a D flip flop to function as an S-R flip flop. Draw the circuit.
- A D.C. generator has an armature e.m.f. of 100 volts, when the useful flux per pole is 20 mWb and the speed is 800 r.p.m.
Calculate the generated e.m.f.
(i) with the same flux and a speed of 1000 r.p.m.
(ii) with flux per pole of 24 mWb and a speed of 900 r.p.m.
- Draw output voltage and current waveforms and determine r.m.s. output voltage of a three-phase half-wave rectifier supplied by three-phase balanced a.c. supply. Also determine the form factor.
If the supply voltage of the above converter is 220 V (r.m.s.) at 50 Hz and the load is of 1 kW at 200 V, purely resistive, determine power consumed by the load with given supply voltage.
- (i) Derive the Maxwell's equation for time varying magnetic field based on Ampere's circuital law.
(ii) A parallel plate capacitor with plate area of $5\,\mathrm{cm}^2$ and plate separation of 3 mm has a voltage of $50 \sin 10^3 t$ V applied to its plates. Calculate the displacement current assuming $\varepsilon = 2\varepsilon_0$.
- Using Thevenin's theorem, find the current through the $40\,\Omega$ resistor connected between terminals a and b in Figure 5(e).
[Figure]
Figure 5(e): 220 V source on the left; $3\,\mathrm{k\Omega}$ top-left and $1\,\mathrm{k\Omega}$ bottom-left in series with node a between them; $400\,\Omega$ top-right and $600\,\Omega$ bottom-right with node b between them; $40\,\Omega$ connected between a and b.
- A buck converter (D.C.-D.C. converter) has LC filter in the output to reduce ripple in output voltage. For continuous conduction mode, draw the waveforms of output voltage, inductor current and capacitor current. If the converter is switched at frequency 'f', prove that minimum values of 'L' and 'C' for $\Delta I_L$ ripple in inductor current and $\Delta V_o$ ripple in output voltages are given by
$$C = \frac{(1-D)}{8L(\Delta V_o/V_o)f^2} \quad \text{and} \quad L = \frac{V_o(1-D)}{(\Delta I_L)f}$$
Assume any data missing. D is duty cycle of switch and $V_o$ is the average output voltage.
- Find $i_o(t)$ in the circuit shown in Figure 6(b) using Fourier transform method when $i_s(t) = 10 \sin 2t$ Amp.
[Figure]
Figure 6(b): current source $i_s(t)$ in parallel with a $2\,\Omega$ resistor and a branch of $4\,\Omega$ in series with $0.5\,\mathrm{F}$ capacitor; $i_o(t)$ flows downward through the $4\,\Omega$ branch.
- Determine the feedback fraction and the operating frequency for the oscillator circuit shown in Figure 6(c).
[Figure]
Figure 6(c): BJT with bias resistors $R_{B_1}$, $R_{B_2}$ from $V_{CC}$, base coupling capacitor $C_C = 100\,\mathrm{pF}$; RFC $= 100\,\mu\mathrm{H}$ at the collector from $V_{CC}$; output coupling $C_C = 100\,\mathrm{pF}$ to $v_o$; tank of $L_1 = 1\,\mu\mathrm{H}$ in parallel with $C_2 = 10\,\mathrm{pF}$ and $C_1 = 100\,\mathrm{pF}$ in series, with their junction grounded; feedback from the $C_1$ end to the base.
- (i) A travelling $\bar{E}$ field in the free space of amplitude 100 V/m strikes a perfect dielectric as shown in Figure 7(a)(i). Determine the value of $E_t$. [10]
[Figure]
Figure 7(a)(i): free space incident $E_i$ on a dielectric slab with $\varepsilon_r = 20$, $\mu_r = 1$, $\sigma = 0$, thickness 1 mm (faces A and B); transmitted $E_t$ in free space beyond B.
(ii) A uniform plane wave in air partially reflects from the surface of a material whose properties are unknown. Measurements of the electric field in front of the interface region yield a 1.5 m spacing between maxima, with the first maximum occurring 0.75 m from the interface. A standing wave ratio of 5 is measured. Determine the intrinsic impedance $\eta_w$ of the unknown material. [10]
- Design a synchronous counter using D flip flop that counts in the following sequence :
6, 3, 5, 0, 2, 6, 3, 5, 0, 2, 6, ...
Draw the circuit.
- A 220 volts, 1500 r.p.m., 50 A separately excited D.C. motor is fed from a three-phase fully controlled rectifier. The rectifier is supplied with a balanced three-phase source with phase voltage of 230 volts (r.m.s.) at 50 Hz. Motor is holding an overhauling load at 1200 r.p.m. at full load torque. Determine the firing angle of converter if armature resistance is assumed to be $0.2\,\Omega$.
- For the circuit shown in Figure 8(a), $v(t) = 311.12 \sin 377t$ volts :
(i) Find the values of $\bar{I}_1$, $\bar{I}_2$, $\bar{I}_3$, $\bar{I}_4$ and $\bar{I}_5$.
(ii) Also compute $\bar{V}_{bc}$ and $\bar{V}_{cd}$.
(iii) Compute the power supplied by the source.
(iv) Find the line power factor.
[Figure]
Figure 8(a): source v(t); $\bar{I}_5$ from source to node a; from a, $\bar{I}_4$ down into a parallel pair of $L_1 = 0.096\,\mathrm{H}$ (current $\bar{I}_1$) and $C_1 = 73.3\,\mu\mathrm{F}$ (current $\bar{I}_2$); from a, $4\,\Omega$ resistor (current $\bar{I}_3$) to node b, then $0.096\,\mathrm{H}$ inductor to node c, then $73.3\,\mu\mathrm{F}$ capacitor to node d.
- Calculate the output voltage $v_o$ in terms of the input voltages $v_{i_1}$, $v_{i_2}$, $v_{i_3}$ and $v_{i_4}$ for the circuit shown in Figure 8(b).
[Figure]
Figure 8(b): op-amp; $v_{i_1}$ through $R_1$ and $v_{i_2}$ through $R_2$ to the inverting terminal, with feedback $R_F$ from output; $v_{i_3}$ through $R_A$ and $v_{i_4}$ through $R_B$ to the non-inverting terminal, which is also connected to ground through $R_C$.
- A single tone FM is represented by the voltage equation as
$v(t) = 12 \cos(6 \times 10^8 t + 5 \sin 1250 t)$.
Determine :
(i) Carrier frequency
(ii) Modulation frequency
(iii) Maximum deviation
(iv) Bandwidth
(v) Power dissipated in a $10\,\Omega$ resistance