Mains PYQs
UPSC Mains Electrical Engineering paper 1 2016 questions
- The reduced incidence matrix of an oriented graph is given as
$$\begin{bmatrix} 0 & -1 & 1 & 0 & 0 \\ 0 & 0 & -1 & -1 & -1 \\ -1 & 0 & 0 & 0 & 1 \end{bmatrix}$$
(i) Draw the graph.
(ii) How many trees are possible for this graph?
(iii) Write the tie-set matrix.
- Determine the overall impulse response, $h(n)$, of the system shown in Fig. 1(b) below. Given that
$h_1(n) = \delta(n) - \left(\frac{1}{5}\right)\delta(n-1)$
$h_2(n) = \delta(n) - \delta(n-1)$
$h_3(n) = \left(\frac{1}{5}\right)^n u(n)$
$h_4(n) = (n-1)u(n)$
$h_5(n) = \delta(n) + n u(n-1) + \delta(n-2)$
where $\delta(n)$ and $u(n)$ denote, respectively, the unit impulse and unit step signals :
[Figure] Fig. 1(b): $h_1(n)$, $h_2(n)$, $h_3(n)$ in cascade, followed by two parallel branches $h_4(n)$ (subtracted, marked -) and $h_5(n)$ (added, marked +), summed at the output.
- Derive an expression for Maxwell's equation in integral form from Ampere's law.
- Two ideal and identical junction diodes are connected as shown in Fig. 1(d). If the current through the reverse-biased diode is $I_0$ and is constant, explain the circuit operation when both the diodes are connected in forward-biased condition. Assume $V_T = 25\,\mathrm{mV}$, $V_\gamma = 0.7\,\mathrm{V}$ and $\eta = 1$ for the diodes.
[Figure] Fig. 1(d): diodes $D_1$ ($V_1$) and $D_2$ ($V_2$) in series in a loop with a battery $V = 50\,\mathrm{mV}$.
- Two impedances $Z_1 = 5\,\Omega$ and $Z_2 = (5 - jX_C)\,\Omega$ are connected in parallel and this combination is connected in series with $Z_3 = (6.25 + j1.25)\,\Omega$. Determine the value of capacitance of $X_C$ to achieve resonance if the supply is 100 V, 50 Hz.
- For the circuit shown in Fig. 2(a), find the value of $V$, if the power dissipation in the load resistance $R_L$ is 36 watts :
[Figure] Fig. 2(a): source $V$ in series with $5\,\Omega$ (voltage $V_1$ across it, marked + $V_1$ -), then $2\,\Omega$ and $4\,\Omega$ in parallel shunt branches; a dependent current source $2V_1$, then $10\,\Omega$ series, $2\,\Omega$ shunt, $5\,\Omega$ series and load $R_L = 4\,\Omega$.
- Consider a continuous-time LTI system for which the input $x(t)$ and output $y(t)$ are related by the following differential equation :
$$\frac{d^2y(t)}{dt^2} - \frac{dy(t)}{dt} - 2y(t) = x(t)$$
Determine the impulse response, $h(t)$, of the system for the following cases by plotting pole-zero pattern :
(i) The system is causal.
(ii) The system is stable.
(iii) The system is neither stable nor causal.
- For the circuit shown in Fig. 2(c), calculate the resistance $R_o$ as seen by the output terminals. Ignore the effect of $R_1$ and $R_2$. Assume $\beta = 99$ and $h_{ie} = 1\,\mathrm{k\Omega}$. Comment on the value of $R_o$ of the circuit :
[Figure] Fig. 2(c): BJT emitter follower with $+V_{CC}$, bias resistors $R_1$ and $R_2$, source $V_s$ with $1\,\mathrm{k\Omega}$ series resistor at the base, emitter resistor $1\,\mathrm{k\Omega}$, output $V_o$ at the emitter, $R_o$ looking into the output.
- Obtain the dotted equivalent circuit for the coupled circuit shown in Fig. 3(a) and hence find the voltage across the capacitor :
[Figure] Fig. 3(a): source $10\angle 0^\circ$ with $5\,\Omega$ in series to a coupled coil of $j5\,\Omega$; mutual coupling $j2\,\Omega$; second coil $j5\,\Omega$ with $5\,\Omega$ in series to source $10\angle 90^\circ$; a capacitor $-j10\,\Omega$ connected across the bottom of the two sides.
- (i) A transmission line has the following parameters :
$Z_L = (200 - j200)\,\Omega$, $Z_0 = 200\,\Omega$
Determine the voltage standing wave ratio and reflection coefficient of the line.
(ii) (1) Write the significance of Smith chart.
(2) Find the length of $x$ of the $100\,\Omega$ transmission line which converts a load impedance $Z_L = (100 + j100)\,\Omega$ to a pure resistance. Also find the value of the resistance $R_x$. Assume VSWR = 2.6.
- For the circuit shown in Fig. 3(c), get the expression for $V_o$. Also sketch the output waveform. Assume that the op-amp is ideal. $R = \sqrt{\frac{L}{C}}$, $\omega = \frac{1}{\sqrt{LC}}$ and $V_i = 10\sin\omega t$ :
[Figure] Fig. 3(c): op-amp with input $V_i$ through series $R$ and $C$ to the inverting terminal; feedback path from output to inverting terminal through $L$ and $R$ in series; non-inverting terminal grounded; output $V_o$.
- Determine the causal signal, $x(n)$, having its $z$-transform
$$X(z) = \frac{1}{(1 + z^{-1})(1 - z^{-1})^2}$$
- (i) Determine the propagation constant $\gamma$ for a material having $\mu_r = 1$, $\varepsilon_r = 8$ and $\sigma = 0.25\,\mathrm{pS/m}$, if the wave frequency is 1.6 MHz.
(ii) Find the skin depth $\delta$ at a frequency of 1.6 MHz in aluminium, where $\sigma = 38.2\,\mathrm{MS/m}$ and $\mu_r = 1$. Also find $\gamma$ and the wave velocity $u$.
- For the op-amp circuit shown in Fig. 4(c), deduce the output voltage expression. Calculate $V_o$, when $R_1 = 1\,\mathrm{k\Omega} = R_2$, $R_3 = 1\,\mathrm{K}$ and $R_4 = 2\,\mathrm{K}$ and $V_{in} = 1\,\mathrm{V}$ :
[Figure] Fig. 4(c): $V_{in}$ feeds the inverting terminal through $R_1$ and the non-inverting terminal through $R_2$; $R_3$ from non-inverting terminal to ground; $R_4$ feedback from output to inverting terminal; output $V_o$.
- If a propagating wave in free space has a potential gradient at any point $(x, y, z)$ as
$$\overline{E} = (-\bar{i} - 2\sqrt{3}\,\bar{j} + 3\bar{k})\,e^{-j\,0.04\pi(\sqrt{3}x - 2y - 3z)}\ \mathrm{V/m}$$
then determine-
(i) the vertical direction of propagation;
(ii) the wavelength of the propagating wave;
(iii) the frequency of the propagating wave;
(iv) the phase velocity and phase velocity vector.
What are the apparent velocities and wavelengths along $x$, $y$ and $z$ directions?
- Minimize the SOP terms given for a Boolean function
$$f(A, B, C, D) = \sum m(2, 3, 8, 10, 11, 12, 14, 15)$$
Implement the minimized function using NAND gates alone.
- What do you mean by V-curves of a synchronous motor? Draw them showing the leading power factor and lagging power factor regions.
- The SCR shown in Fig. 5(c) has a $\frac{di}{dt}$ limit of $10\,\mathrm{A/\mu s}$. It is to be operated from a 100 V d.c. supply with load resistance $R = 50\,\Omega$.
(i) What is the minimum value of load inductance $L$ that will protect the SCR?
(ii) If an $R_sC_s$ snubber is connected across the SCR with $R_s = 500\,\Omega$, what will be the new value of load inductance $L$ to protect the SCR against $\frac{di}{dt}$?
[Figure] Fig. 5(c): supply $V_s = 100\,\mathrm{V}$, series $L$, $R = 50\,\Omega$ and SCR with gate current $i_g$.
- Compare Amplitude Modulation (AM) and Frequency Modulation (FM).
- A 20 hp, 230 V, 1150 r.p.m. d.c. shunt motor has four poles, four parallel armature paths and 882 armature conductors. The armature circuit resistance is $0.188\,\Omega$. At rated speed and rated output, the armature current is 73 A and the field current is 1.6 A. Calculate the electromagnetic torque.
- Identify the circuit shown in Fig. 6(a). Briefly explain the same. Calculate the current $i$ and $V_o$, if $V_R = 5\,\mathrm{V}$ and $R = 5\,\mathrm{k\Omega} = R_F$ :
[Figure] Fig. 6(a): R-2R ladder network with input $V_R$ through series $R$ resistors, shunt $2R$ resistors to ground, final series $2R$ to ground carrying current $i$; op-amp summing amplifier with feedback $R_F$, output $V_o$.
- The resistances and leakage reactances of a 10 kVA, 50 Hz, 2300/230 V distribution transformer are
$r_1 = 3.96\,\Omega$ and $r_2 = 0.0396\,\Omega$, $x_1 = 15.8\,\Omega$ and $x_2 = 0.158\,\Omega$
Subscript 1 refers to HV and 2 refers to LV winding
The transformer delivers rated kVA at 0.8 p.f. lagging to a load on the LV side. Find the HV side voltage necessary to maintain 230 V across load terminals. Also find the percentage voltage regulation.
- Explain the operations of phase-locked loop used as FM demodulator with neat sketch.
- What is a PLA? Realize the following functions using an appropriate PLA :
$f_1 = AB + CD$
$f_2 = \bar{A}B + A\bar{B}$
$f_3 = AD + BC + \bar{B}D$
- A 200 V, 875 r.p.m., 150 A, separately excited d.c. motor has an armature resistance of $0.06\,\Omega$. The motor armature terminals are fed from a single-phase fully controlled bridge rectifier. The input a.c. supply to bridge rectifier is 240 V, 50 Hz. Assuming continuous and ripple-free armature current, determine the following :
(i) Firing angle of SCRs for rated torque and 750 r.p.m.
(ii) Firing angle for rated torque and $-500$ r.p.m.
Assume that field winding of the motor is connected to a constant d.c. voltage source.
- Write a short note on white noise.
- A single-phase full-bridge square-wave inverter is supplying power to a purely resistive load of $20\,\Omega$. The d.c. source voltage is 600 V. If the inverter is to operate at 500 Hz with an r.m.s. load voltage 500 V, find-
(i) average power absorbed by the load;
(ii) average source current (assume no losses in switching);
(iii) average current of each switch.
- A 3-phase, 4-pole, 50 hp, 440 V, 60 Hz, Y-connected induction motor has the following parameters per phase :
$r_1 = 0.10\,\Omega$, $x_1 = 0.35\,\Omega$
$r_2' = 0.12\,\Omega$, $x_2' = 0.40\,\Omega$
It is known that the stator core loss amounts to 1200 W and the rotational losses equal 950 W. Moreover, at no-load the motor draws a line current of 18 A at a power factor of 0.089 lagging. When the motor operates at a slip of 2.5%, find the input line current and power factor.
- A class-A chopper circuit is supplied from a d.c. source voltage 100 V. The chopper supplies power to a series $R$-$L$ load with $R = 0.5\,\Omega$ and $L = 1\,\mathrm{mH}$. The chopper switch is ON for 1 ms in an overall period of 3 ms. Calculate average load voltage, maximum and minimum value of load current and average load current. Assume continuous current operation of the chopper.
- Explain in detail about pre-emphasis and de-emphasis in Frequency Modulation (FM).