Mains PYQs
UPSC IFoS Mains Civil Engineering paper 1 2022 questions
- In a tension test, a steel rod of gauge length 255 mm and diameter 32 mm was used. The rod during the test was stretched 0.108 mm under a pull of 65 kN. In a torsion test, the same rod was twisted 0.018 radian over a length of 255 mm at the torque of $500 \times 10^3$ N-mm. Determine the modulus of elasticity, modulus of rigidity, Poisson's ratio and bulk modulus.
- The tension in cable $BC$ is 750 N. Determine the resultant of the three forces exerted at point $B$ of the beam $AB$ :
[Figure]
Figure labels: 850 mm, 810 mm, forces 790 N (slope 13, 5, 12) and 495 N (slope 5, 4, 3) at $B$.
- Determine the vertical movements of joint $C$ of the truss shown in the figure below, if the member $FG$ is lengthened by 55 mm. Use the principle of virtual work :
[Figure]
Figure labels: joints $B, C, E, G, I$ (top), $A, D, F, H, J$ (bottom); height 3 m; four panels of 4 m each.
- Using the unit load method, determine the vertical and horizontal deflection of the free end of the frame as shown in the figure below. Support $A$ is fixed, $B$ is rigid joint and point $C$ is free. $BC = I$ and $BA = 2I$. Take $E = 210$ GPa and $I = 300 \times 10^{-6}\,\mathrm{m^4}$ :
[Figure]
Figure labels: 5 kN at $B$, 10 kN at $C$, $BC$ = 2 m, $BA$ = 3 m.
- With the help of neat sketches, explain the stress concept and load-balancing concept of prestressing.
- Design a slab base for a column ISHB 300 @ 577 N/m carrying an axial factored load of 1200 kN and a factored bending moment of 30 kN-m about its major axis. M-20 grade concrete is used for the foundation. Provide welded connection between the column and base plate. Assume that the ends of the column are properly machined. Use Fe-410 grade steel. Take bearing strength of concrete = $0.45 f_{ck}$. The design bending strength of the base plate may be taken as $M_d = 1.2\, Z_e \frac{f_y}{\gamma_{m0}}$, where $Z_e$ is the elastic section modulus of the cross-section.
The properties of ISHB 300 @ 577 N/m are as under :
Depth = 300 mm
Width of flange = 250 mm
Thickness of flange = 10.6 mm
Thickness of web = 7.6 mm
Sectional area = $7484.95\,\mathrm{mm^2}$
$I_{zz} = 12545.2\,\mathrm{cm^4}$
$I_{yy} = 2193.6\,\mathrm{cm^4}$
$r_{zz} = 129.5$ mm
$r_{yy} = 54.1$ mm
For Fe-410 grade steel : $f_u = 410\,\mathrm{N/mm^2}$, $f_y = 250\,\mathrm{N/mm^2}$
Take $\gamma_{m0} = 1.1$ and $\gamma_{mw} = 1.25$
- A three-hinged parabolic arch of constant cross-section is subjected to uniformly distributed load over a part of its span and a concentrated load of 55 kN as shown in the figure below. Determine the horizontal thrust and the maximum bending moment in the arch :
[Figure]
Figure labels: 55 kN load at $D$, 5 m from $A$; UDL 10 kN/m near crown $C$; 3 m and 3.75 m heights; spans 10 m and 15 m; supports $A$ and $B$ with reactions $H_A$, $A_y$, $H_B$, $B_y$.
- Determine the tensile strength of a roof truss member made of 2 ISA 9060, 6 mm and connected to the gusset plate of 10 mm thickness by 4 mm weld as shown in the figure below. The effective length of the weld is 250 mm. Steel used is of Fe-410 grade quality. Use the limit state method of design :
[Figure]
Figure labels: ISA 9060, 6 mm; 4 mm weld; 90 mm; 60 mm; gusset plate 10 mm thick.
Given : $\gamma_{m0} = 1.1$ and $\gamma_{m1} = 1.25$
For ISA 9060, 6 mm : $A_g = 865\,\mathrm{mm^2}$
For Fe-410 : $f_u = 410\,\mathrm{N/mm^2}$, $f_y = 250\,\mathrm{N/mm^2}$
Formulae :
$$T_{dg} = \frac{A_g f_y}{\gamma_{m0}}$$
$$T_{dn} = \frac{0.9 f_u A_{nc}}{\gamma_{m1}} + \frac{\beta A_{go} f_y}{\gamma_{m0}}$$
where $\beta = 1.4 - 0.076\left(\frac{w}{t}\right)\left(\frac{f_y}{f_u}\right)\left(\frac{b_s}{L_w}\right) < \left(\frac{f_u \gamma_{m0}}{f_y \gamma_{m1}}\right) > 0.7$
$$T_{db1} = \frac{A_{vg} f_y}{\sqrt{3}\,\gamma_{m0}} + \frac{0.9 A_{tn} f_u}{\gamma_{m1}}$$
$$T_{db2} = \frac{0.9 A_{vn} f_u}{\sqrt{3}\,\gamma_{m1}} + \frac{A_{tg} f_y}{\gamma_{m0}}$$
- The roof of a hall measuring $8\,\mathrm{m} \times 15\,\mathrm{m}$ consists of 100 mm thick reinforced concrete slab supported on steel I-beams spaced at 3 m apart as shown in the figure below. The finishing load is $1.5\,\mathrm{kN/m^2}$ and live load is $1.5\,\mathrm{kN/m^2}$. ISMB 400 is readily available. Check the adequacy of the ISMB 400 for use as beam in the hall. The permissible deflection for the beam is ($l_e/300$).
[Figure]
Figure labels: five spacings of 3 m; width 8 m; 0.3 m bearing at each end.
The properties of ISMB 400 are as under :
Depth of section, $h = 400$ mm
Width of flange, $b = 140$ mm
Sectional area, $A = 7845.58\,\mathrm{mm^2}$
Thickness of flange, $t_f = 16.0$ mm
Thickness of web, $t_w = 8.9$ mm
Depth of web, $d (= h_1) = 333.4$ mm
$I_{zz} = 20458.4 \times 10^4\,\mathrm{mm^4}$
$I_{yy} = 622.1 \times 10^4\,\mathrm{mm^4}$
$Z_p = 1176.163 \times 10^3\,\mathrm{mm^3}$
Weight of section = 0.604 kN/m
For steel : $f_y = 250\,\mathrm{N/mm^2}$, $f_u = 410\,\mathrm{N/mm^2}$, $\gamma_{m0} = 1.1$
Formulae :
$$\varepsilon = \left(\frac{250}{f_y}\right)^{1/2}; \quad V_d = \frac{A_v f_{yw}}{\sqrt{3}} \times \frac{1}{\gamma_{m0}}$$
For $\frac{d}{t_w} < 67\varepsilon$ and $V \le 0.6 V_d$
$$M_d = \frac{\beta_b Z_p f_y}{\gamma_{m0}} < \frac{1.2 Z_e f_y}{\gamma_{m0}} \text{ (for simply supported beam)}$$
| Ratio | Plastic | Compact | Semi-compact |
|---|---|---|---|
| $b/t_f$ | $9.4\varepsilon$ | $10.5\varepsilon$ | $15.7\varepsilon$ |
| $d/t_w$ | $84\varepsilon$ | $105\varepsilon$ | $126\varepsilon$ |
For plastic section, $\beta_b = 1.0$
- Design an RCC circular water tank with flexible base for a capacity of 500 kL. The depth of water is to be 4 m, including a freeboard of 0.2 m. The tank is resting on the ground and is open at the top. Use M-25 grade concrete and Fe-415 grade steel. The reinforcement bars of 20 mm $\phi$, 10 mm $\phi$ and 8 mm $\phi$ are available.
Take unit weight of water = $10\,\mathrm{kN/m^3}$
For M-25 concrete : $\sigma_{cbc} = 8.5\,\mathrm{N/mm^2}$, $\sigma_{ct} = 1.3\,\mathrm{N/mm^2}$
For Fe-415 steel : $\sigma_s = 150\,\mathrm{N/mm^2}$
- A thick spherical shell having internal diameter of 150 mm is subjected to an internal fluid pressure of $25\,\mathrm{N/mm^2}$. If the maximum hoop stress is 100 MPa, determine the thickness of the spherical shell.
- An RCC cantilever retaining wall is used to retain a level earthfill of 4.0 m above the ground level. Due to construction of a building, there is a surcharge of $40\,\mathrm{kN/m^2}$ on the earthfill. A good soil for foundation is at a depth of 1.25 m below the ground level with a safe bearing capacity of $160\,\mathrm{kN/m^2}$. The unit weight and the angle of repose of the soil are $16\,\mathrm{kN/m^3}$ and $30^\circ$ respectively. Assume the coefficient of friction between soil and concrete to be 0.50. The initial proportioning of the retaining wall is shown in the figure below :
[Figure]
Figure labels: surcharge; earthfill; stem top width 200 mm; stem base 650 mm; height 4.0 m above GL; 1.25 m below GL; base slab thickness 620 mm; toe-to-stem 2600 mm; total base 3900 mm.
(i) Check whether shear key is required. Ignore the passive pressure.
(ii) Design the stem of the retaining wall.
Use M-20 grade concrete and Fe-415 grade steel.
| $\frac{100 A_s}{bd}$ | $\tau_c$ for M-20 ($\mathrm{N/mm^2}$) |
|---|---|
| 0.25 | 0.36 |
| 0.50 | 0.48 |
| 0.75 | 0.56 |
| 1.00 | 0.62 |
- Determine the plastic moment capacity and the shape factor of the I-section shown in the figure below, if the value of the yield stress is 300 MPa :
[Figure]
Figure labels: flanges 95 mm wide, 10 mm thick; web 8 mm thick; overall depth 240 mm.
- Using the consistent deformation method, analyze the beam shown in the figure below. Take $EI$ is constant throughout :
[Figure]
Figure labels: $A$ fixed; 75 kN at $D$; support at $B$; 25 kN at free end $C$; spans $AD$ = 2.5 m, $DB$ = 2.5 m, $BC$ = 2.5 m.
- A centrifugal pump is installed at a height of 3.0 m from water surface. The atmospheric pressure is 101 kPa, vapour pressure is 2.58 kPa, inlet and other losses in suction pipe are 1.96 m, manometric head of the pump is 49.2 m and Thomas cavitation parameter, $\sigma = 0.120$. Check whether cavitation develops in the pump or not. What is the preferable height of the pump above water surface in order to avoid cavitation?
- An aircraft is travelling at a speed of 350 kmph against a wind velocity of 25 kmph. A Pitot static tube is mounted on the aircraft to measure the pressure. If the specific weight of air is $12\,\mathrm{N/m^3}$ and coefficient of velocity of the Pitot tube = 0.98, determine the pressure difference recorded in the instrument.
- At a particular site, the ground surface is at El. 0.0 m and the groundwater level is at El. (-)10.0 m. The degree of saturation, $S$, above the water table decreases towards the ground surface. The decrease in $S$ is linear and continuous towards the surface. However for this problem, it can be treated as two zones of different average degree of saturation, $S$, as given below :
El. 0.0-(-)5.0 m : $S$ = 25%
El. (-)5.0-(-)10.0 m : $S$ = 75%
The soil has a void ratio, $e = 0.4$ and specific gravity, $G_s = 2.7$. Determine the total stress and effective stress at El. (-)20.0 m. Assume unit weight of water, $\gamma_w = 9.81\,\mathrm{kN/m^3}$.
- Define major principal stress, minor principal stress and deviator stress. A sample of dry cohesionless soil has an angle of internal friction of approximately $35^\circ$. If the minor principal stress is 105 kPa, at what value of deviator stress and major principal stress is the sample likely to fail?
- A precast concrete pile $300\,\mathrm{mm} \times 300\,\mathrm{mm}$ in cross-section is driven into a medium stiff clay and it is to carry a load of 300 kN. The unconfined compressive strength of the clay is $100\,\mathrm{kN/m^2}$. If the adhesion factor, $\alpha = 0.5$ and a factor of safety of 2 is desired for the safety of the structure, determine the depth of penetration required for the pile to carry the above load of 300 kN. Also determine the allowable load capacity of a circular pile of equivalent cross-sectional area and same length with the same factor of safety of 2. Finally comment on the result.
- A sample of normally consolidated clay was obtained from the mid-height of a compressible clay layer as shown in the figure below. A consolidation test was conducted on a portion of this sample. The results of the consolidation test are as follows :
| $p$ (kPa) | 80 | 160 | 320 | 640 | 1280 |
|---|---|---|---|---|---|
| $e$ | 1.50 | 1.42 | 1.30 | 1.12 | 0.94 |
The natural void ratio (initial, $e_0$) of the clay existing in the field is 1.65. A footing is to be located at 1.5 m below the ground level as shown in the figure below. The base of the footing is $3\,\mathrm{m} \times 3\,\mathrm{m}$ and it exerts a total load of 2500 kN. Plot a $e$-log $p$ curve using the pressure void ratio data and determine the compression index, $C_c$. Also determine the total expected consolidation settlement of the clay layer. Assume unit weight of water, $\gamma_w = 9.81\,\mathrm{kN/m^3}$ :
[Figure]
Figure labels: footing 3 m x 3 m at 1.5 m depth; sand and gravel, $\gamma = 19\,\mathrm{kN/m^3}$, 1.5 m thick down to water table (WT); sand and gravel, $\gamma = 20.5\,\mathrm{kN/m^3}$, 3.0 m thick; normally consolidated clay, $\gamma = 17.3\,\mathrm{kN/m^3}$, 3.0 m thick.
- (i) A hemispherical bowl of radius 1.60 m is full of water and is rotated about its vertical axis at 25 r.p.m. Calculate the amount of water that will overflow due to rotation of the bowl with that speed. [8]
(ii) If the velocity potential for a two-dimensional flow is given by $\phi = x(2y - 3)$, determine the velocity at point $N(2, 3)$ and find the stream function and check whether the flow is irrotational or not. [7]
- A rectangular channel having 2.0 m width carries uniform flow of water at a depth of 1.6 m. The velocity of the flow is 0.80 m/s. If there is a bump of 34 cm raise in the bed and the bump is covering full width of the channel bed, find the change in upstream depth of flow. What is the maximum raise in the bump in the bed that will be permissible so that there is no change in the upstream depth of flow? Assume that the head loss between the bump and upstream section is neglected.
- What are the differences between general shear failure and local shear failure in shallow footing? Where do they occur? A load test was made with a 300 mm square plate at a depth of 1.0 m below the ground level in a clayey soil. The water table was located at a depth of 1.5 m below the ground level. The failure occurred at a load of 52 kN. What would be the ultimate bearing capacity for a 1.5 m wide continuous footing with its base located at the same depth in the same soil? Assume unit weight of the soil, $\gamma = 18.6\,\mathrm{kN/m^3}$ both above and below the water table.
- What is 'negative skin friction'? What are the reasons that could lead to the development of 'negative skin friction' in a pile foundation? Explain with the help of neat sketches. How is 'negative skin friction' estimated for a single pile?
- (i) A Pelton turbine works under a head of 260 m and develops a power of 5820 kW. Its revolving speed is 240 r.p.m. The overall efficiency of the turbine is 80%. Find the unit discharge, unit power and unit speed. Assume that the efficiency is constant under different heads. If the head on the same turbine falls down to 130 m, find the unit quantities for discharge, power and speed for this head. [10]
(ii) Explain the various functions of draft tube in reaction turbines and define the efficiency of the draft tube. Write the equation for draft tube efficiency. [5]
- Four footings carrying an overhead tank are placed on the ground with the base of the footing close to the ground level. The centers of these footings form a square of 8 m sides and each of them carries a load of 600 kN. Calculate the vertical stress due to the footing loads by Boussinesq's point load equation at a depth 5 m (i) vertically below the center of any of the footings and (ii) vertically below the center of square joining the center of the footing.
- (i) Explain boundary layer separation along with figure and also explain the methods of controlling the boundary layer. [5]
(ii) A notch is provided at the top of one of the sides of a steel tank. The horizontal area of cross-section of the tank is $2.20\,\mathrm{m^2}$. Water is flowing into the tank at a constant rate and is discharging over the notch steadily. The head over the crest of the notch at steady state is 0.35 m. When the supply of water into the tank was suddenly stopped, it was observed that the head over the crest started to fall at the rate of 4.80 mm/s. When the head over the notch had fallen to 0.19 m, it was observed that the head over the crest was falling at the rate of 2.1 mm/s. Estimate the rate of flow into the tank when there is steady head of 0.28 m over the notch. Assume the discharge equation of the notch as $Q = CH^n$. [10]
- Water is flowing through a pipe of 10 m length and 100 mm diameter. The velocity of the flow of water is 2.8 m/s. If the central 4.0 m length of the pipe is replaced by 150 mm diameter pipe, find the savings in loss of head and the corresponding power. The change of section is sudden. Take coefficient of friction, $f = 0.05$ for both the pipes.