Mains PYQs
UPSC IFoS Mains Civil Engineering paper 1 2017 questions
- A force of $100\,\mathrm{N}$ is directed along the line that is drawn from the point $\mathrm{A}(5, 2, -1)\,\mathrm{m}$ to the point $\mathrm{B}(3, -4, 7)\,\mathrm{m}$. Determine the moment of this force about the 'z'-axis.
- If two pieces of materials 'A' and 'B' have the same bulk modulus, but the value of Modulus of Elasticity for 'B' is $1\%$ greater than that for 'A', find the value of Modulus of Rigidity for the material 'B' in terms of Modulus of Elasticity and Modulus of Rigidity for material 'A'.
- A cantilever beam 'AB' of length $4\,\mathrm{m}$ is subjected to a concentrated load of $2\,\mathrm{kN}$ and a couple of $0.5\,\mathrm{kNm}$ acting at the free end as shown in the figure below. Determine the slope and deflection at the free end using Moment Area Method.
[Figure] Cantilever AB fixed at A, length 4 m, $2\,\mathrm{kN}$ load at free end B and $0.5\,\mathrm{kNm}$ couple at B.
- A simply supported beam of a beam and slab system, rests on a support of width $380\,\mathrm{mm}$. The clear span of the beam is $10.5\,\mathrm{m}$. The thickness of the slab is $125\,\mathrm{mm}$. The width of the beam is $250\,\mathrm{mm}$ and the depth of the beam below the slab is $475\,\mathrm{mm}$. The beam is reinforced with one row of $25\,\mathrm{mm}$ diameter steel reinforcements of grade Fe 415. The total load including the superimposed dead load, live load and its own weight is $35\,\mathrm{kN/m}$ at service stage. Compute the maximum ultimate design shear stress in concrete.
- The diameter of a ring beam in a water tank is $12.5\,\mathrm{m}$. It is subjected to an outward radial force of $25\,\mathrm{kN/m}$. Design the section using M 25 grade of concrete and Fe 415 steel. Take $m = 11$ and the allowable stress in concrete in tension is $1.2\,\mathrm{N/mm^2}$.
- A uniform T-section beam is $100\,\mathrm{mm}$ wide and $150\,\mathrm{mm}$ deep with a flange thickness of $25\,\mathrm{mm}$ and a web thickness of $12\,\mathrm{mm}$. If the limiting bending stresses for the material of the beam are $80\,\mathrm{MN/m^2}$ in compression and $160\,\mathrm{MN/m^2}$ in tension, find the maximum U.D.L. that the beam can carry over a simply supported span of $5\,\mathrm{m}$.
- A steel column consisting of ISMB 350 is effectively restrained at mid-height by a bracing member in Y-Y direction, but is free to move in Z-Z direction and both the ends of the column are pinned. Its unsupported length is $6\,\mathrm{m}$. Determine its axial load carrying capacity at service loads, using the limit state design of IS : 800 - 2007.
Design compressive strength $f_{cd} = \dfrac{f_y/\gamma_{mo}}{\phi + [\phi^2 - \lambda^2]^{0.5}}$,
where $\phi = 0.5[1 + \alpha(\lambda - 0.2) + \lambda^2]$
$\lambda = \sqrt{\dfrac{f_y}{f_{cc}}}$
Euler buckling stress $f_{cc} = \dfrac{\pi^2 E}{\left(\dfrac{KL}{r}\right)^2}$
and $\alpha = 0.34$ for buckling class 'b'
$= 0.21$ for buckling class 'a'
$f_y = 250\,\mathrm{N/mm^2}$
$\gamma_{mo} = 1.10$ and $\gamma_f = 1.5$
$E = 2 \times 10^5\,\mathrm{N/mm^2}$
Minimum radius of gyration for ISMB 350 is given below :
$r_{yy} = 28.4\,\mathrm{mm}$
$r_{xx} = 142.9\,\mathrm{mm}$
Area of cross-section of the ISMB 350 is $6671\,\mathrm{mm^2}$.
- In the framed structure shown in the figure below, if the length of all the members is the same, determine the force in the member 'DE' using the Virtual Work Method.
[Figure] Truss with joints A, B, C, D, E; supports A and B with reactions $R_a$ and $R_b$; $200\,\mathrm{N}$ loads at D and E.
- A railway wagon weighs $0.25\,\mathrm{MN}$ when empty and $0.6\,\mathrm{MN}$ when loaded. The springs of the wagon get compressed by $8\,\mathrm{cm}$ when it is full. Determine the natural period of vibration when the wagon is empty and when it is loaded.
- A welded bracket connects a plate to the column flanges as shown in the figure. Determine the size of weld if the allowable stress in the weld is $110\,\mathrm{N/mm^2}$.
[Figure] Bracket plate welded to column ISMB 400, weld length $450\,\mathrm{mm}$, load $200\,\mathrm{kN}$ at $200\,\mathrm{mm}+200\,\mathrm{mm}$ from the weld line.
- A simply supported beam of span $8\,\mathrm{m}$ is subjected to a series of rolling loads as shown. Determine the position of loads and the absolute maximum Bending Moment.
[Figure] Loads: (1) $80\,\mathrm{kN}$, then $1.8\,\mathrm{m}$, (2) $100\,\mathrm{kN}$, then $1.2\,\mathrm{m}$, (3) $70\,\mathrm{kN}$, then $2.4\,\mathrm{m}$, (4) $100\,\mathrm{kN}$.
- A beam with a rectangular cross-section of size $250\,\mathrm{mm}$ wide and $500\,\mathrm{mm}$ deep is prestressed by a force of $500\,\mathrm{kN}$ using 8 Nos. of $7\,\mathrm{mm}$ $\phi$ steel cables located at an eccentricity of $80\,\mathrm{mm}$. Find the loss of prestress due to creep of concrete. Grade of concrete is M 40. Coefficient of creep is taken as 1.8. Modulus of Elasticity of steel $E_s$ is $2 \times 10^5\,\mathrm{N/mm^2}$. Assume the stress at transfer is $80\%$.
- A continuous beam ABC is loaded as shown in the figure below. Determine the required Plastic Moment ($M_P$) of the beam section if the load factor is 3.2.
[Figure] Beam ABC: span AB $12\,\mathrm{m}$ with $5\,\mathrm{kN/m}$ UDL and plastic moment $M_P$; span BC with point loads $60\,\mathrm{kN}$ at D and $90\,\mathrm{kN}$ at E, plastic moment $2M_P$, distances $8\,\mathrm{m}$, $8\,\mathrm{m}$, $8\,\mathrm{m}$ (B to D, D to E, E to C).
- A masonry retaining wall, trapezoidal section is $1.2\,\mathrm{m}$ wide at the top. Its earth retaining face is vertical and smooth. The retained earth, having density of $16\,\mathrm{kN/m^3}$ and angle of shearing resistance of $30^\circ$, is level with the top of the wall. Height of the wall is $6.9\,\mathrm{m}$. The density of masonry is $19.5\,\mathrm{kN/m^3}$. Calculate the maximum bottom width of the wall, so that no tension is to be developed at the base. Also calculate the maximum base pressure at this width.
- Two ISA $90 \times 90 \times 8\,\mathrm{mm}$ carry a load of $180\,\mathrm{kN}$ and are placed back to back through $8\,\mathrm{mm}$ gusset plate. The permissible shear stress is $110\,\mathrm{N/mm^2}$ and bearing stress is $250\,\mathrm{N/mm^2}$. Design the riveted connection and show the arrangement with a neat sketch.
- The velocity potential for a two-dimensional flow is $\phi = x(2y - 1)$. Determine the value of stream function at a point $\mathrm{P}(4, 5)$. Comment whether the flow is rotational or irrotational. Also determine the velocity at the point $\mathrm{P}(4, 5)$.
- A three-cylinder car has pistons of $75\,\mathrm{mm}$ and cylinders of $75\,\mathrm{mm}$. Find the percentage change in force required to drive the piston, when the lubricant warms from $25^\circ\mathrm{C}$ to $100^\circ\mathrm{C}$. The dynamic viscosity of the lubricant at $25^\circ\mathrm{C}$ is $2\,\mathrm{Ns/m^2}$ and at $100^\circ\mathrm{C}$, it is $0.4\,\mathrm{Ns/m^2}$.
- A soil sample is tested in the laboratory for classification. The test results are as follows :
Percentage passing $4.75\,\mathrm{mm}$ IS sieve $= 58$
Percentage passing $75\,\mu$ IS sieve $= 11$
The particle size $D_{60} = 6.3\,\mathrm{mm}$
$D_{30} = 0.5\,\mathrm{mm}$
$D_{10} = 0.07\,\mathrm{mm}$
Liquid limit $= 42$
Plastic limit $= 21$
Classify the soil.
- A constant head permeability test was run on a sand sample $400\,\mathrm{mm}$ long and $3000\,\mathrm{mm^2}$ in area. When the loss of head was $900\,\mathrm{mm}$, the quantity of water collected in 3 minutes was $400\,\mathrm{ml}$.
(i) Determine the coefficient of permeability of the soil.
(ii) If the specific gravity of grains is 2.65 and the dry mass of the sample is $1.9\,\mathrm{kg}$, find the void ratio of the sample.
- Compare the salient features of Standard Penetration Test and Plate Load Test.
- Find the hydraulic efficiency of a Pelton turbine operating under a head of $350\,\mathrm{m}$, with a discharge of $15\,\mathrm{m^3/s}$.
The other data are :
Speed ratio $K_u = 0.46$
Coefficient of velocity $C_v = 0.985$
$V_{r_2} = 0.9\,V_{r_1}$ and $\phi = 20^\circ$
- A raft of size $4\,\mathrm{m} \times 4\,\mathrm{m}$ carries a uniform load of $200\,\mathrm{kN/m^2}$. Find the stress at $6\,\mathrm{m}$ below the raft centre considering both geostatic stress and induced stress. Use point load approximation with four equivalent point loads. Take $\gamma_{soil} = 20\,\mathrm{kN/m^3}$.
- There is a bed of compressible clay of $3\,\mathrm{m}$ thickness with pervious sand on top and impervious rock at the bottom. In a consolidation test on an undisturbed specimen of this clay, $90\%$ settlement is reached in 6 hours. The specimen was $20\,\mathrm{mm}$ thick. Estimate the time in years for the building, founded over this deposit, to reach $90\%$ of its final settlement.
- What is hydraulic jump ? Explain the uses of hydraulic jump in brief. Derive the equation for sequent depth ratio, for a hydraulic jump in a horizontal rectangular channel. What are the assumptions used in deriving the sequent depth ratio ?
- A rectangular channel is $4.0\,\mathrm{m}$ wide and conveys a discharge of $20\,\mathrm{m^3/s}$ at a depth of $2.2\,\mathrm{m}$. It is proposed to reduce the width of the channel at a hydraulic structure. Assuming the transition to be horizontal and the flow to be frictionless, determine the water surface elevations upstream and downstream of the constriction when the constricted width is $2.8\,\mathrm{m}$.
- A gravity retaining wall retains $12\,\mathrm{m}$ of backfill, $\gamma = 18\,\mathrm{kN/m^3}$, $\phi = 30^\circ$ with a uniform horizontal surface. Assuming the wall interface to be vertical, determine the magnitude and point of application of total active pressure. If the water table is $3\,\mathrm{m}$ below the ground surface, how far do the magnitude and point of application of active pressure change ? Assume submerged unit weight of soil as $11\,\mathrm{kN/m^3}$.
- Two reservoirs $10\,\mathrm{km}$ apart have a difference of water level of $25\,\mathrm{m}$ and are connected together by a pipeline. The pipeline consists of a $6\,\mathrm{km}$ single pipe feeding a junction from which two pipes run in parallel for the remaining length of $4\,\mathrm{km}$ to the lower reservoir. If the same size of pipe is used throughout, what should be the diameter for the pipe so that velocity may not exceed $1.25\,\mathrm{m/s}$ ? Take the friction coefficient $f = 0.03$.
- For the following data, compute the settlement of the group assuming the load to be transferred at two-thirds the length of a pile :
Depth of clay layer $= 16\,\mathrm{m}$, load on piles $= 2000\,\mathrm{kN}$, length of piles $= 10.5\,\mathrm{m}$, diameter of a pile $= 0.45\,\mathrm{m}$, spacing of piles $= 1.25\,\mathrm{m}$ c/c, number of piles $= 16$, initial void ratio $= 0.80$, $C_c = 0.45$ and unit weight of soil $= 16.5\,\mathrm{kN/m^3}$. Take size of pile cap $5.65 \times 5.65\,\mathrm{m}$.
- A pipe of diameter $1.5\,\mathrm{m}$ is required to transport an oil of specific gravity 0.9 and viscosity $3 \times 10^{-2}$ poise at the rate of 3000 litres/s. Tests were conducted on a $15\,\mathrm{cm}$ diameter pipe using water at $20^\circ\mathrm{C}$. Find the velocity and rate of flow in the model. Viscosity of water at $20^\circ\mathrm{C}$ is 0.01 poise.