Mains PYQs
UPSC Mains Civil Engineering paper 1 2026 questions
- A frictionless pulley $A$ as shown in the figure is supported by two bars $AB$ and $AC$ which are hinged at $B$ and $C$ to a vertical wall. A flexible cable, hinged at $D$, goes over the pulley and supports a load 30 kN at the other end $E$. The angles between the members are shown in the figure. Neglecting the size of the pulley, determine the forces in the bars $AB$ and $AC$ by drawing the free body diagram :
[Figure]
Angles: 60° at $B$ (between wall and $AB$), 60° at $D$ and 30° at $A$ (between cable $DA$ and bar $AC$), 30° at $C$; load 30 kN at $E$ hanging from $A$; frictionless pulley at $A$.
- Draw the bending moment diagram and shear force diagram for the beam $ABCD$. The beam supports a point load of 12 kN as shown in the figure :
[Figure]
$AB$ = 2 m fixed at $A$; 0.6 m from $B$ down to $C$; $CD$ = 0.3 m; 12 kN load at $D$.
- Determine the 'shape factor' for the diamond-shaped section shown in the figure :
[Figure]
Depth $d$ ($d/2$ above and $d/2$ below the centroid), width $b$.
- A pretensioned beam 250 mm wide and 300 mm deep is prestressed by 12 wires (each 6 mm diameter) initially stressed to 1200 MPa with their centroid located at 100 mm from the soffit. Estimate the final percentage loss of stress due to elastic shortening, shrinkage, relaxation of steel and creep effect. Assume that the modulus of elasticity of steel and concrete are 210 kN/mm$^2$ and 35 kN/mm$^2$ respectively, creep coefficient = 1.6, residual shrinkage strain = $3\times10^{-4}$ and relaxation of steel stress = 90 MPa.
- A steel plate girder is subjected to a maximum factored shear force of 2800 kN. The cross-section of the girder is shown in the figure. Design a suitable fillet weld to connect flange plates to the web. Assume shop welding. E250 grade of steel having $f_u$ = 410 MPa is used. Use limit state method of design. Take $\gamma_{mw}$ = 1.25 :
[Figure]
Flange plates 650 mm wide and 25 mm thick (top and bottom); web 1500 mm deep and 15 mm thick.
- Using limit state method, design a reinforced concrete circular column (with lateral ties) of height 3.0 m. It is subjected to an unfactored axial load of 1150 kN (dead load + live load). Use M25 grade of concrete and Fe500 grade of steel. Take effective length factor as 1.2. Show the design details in a neat sketch.
- A straight bar of alloy is mounted in a strut-testing machine with both ends pin jointed and loaded axially till it buckles. Using Euler's formula, calculate the maximum central deflection before the alloy material attains the yield point at 300 MN/m$^2$. Take bar length = 2.0 m, cross-section of the bar as 20 mm $\times$ 15 mm and modulus of elasticity $E$ as 90 GN/m$^2$.
- Using moment distribution method, analyse the structure $ABCD$ shown in the figure (joint $B$ is rigid). The loading on the structure, moment of inertia of the members and other dimensions are clearly mentioned in the figure. Give neat sketch of bending moment and shear force diagram, indicating their values in the diagram :
[Figure]
$A$ is fixed at the left end; 100 kN load 4 m from $A$; 3 m to joint $B$ (both with $2I$); 80 kN load 2 m from $B$; 3 m further to $C$ (fixed, $I$); column $BD$ 5 m long with $2I$, fixed at $D$.
- A vertical member in a truss is subjected to the following member force (factored) :
(i) Compressive force = 30 kN (dead and live load)
(ii) Tensile force = 150 kN (dead and wind load)
The member is composed of two numbers ISA 100 $\times$ 100 $\times$ 8 connected to both sides of the gusset plate of thickness 10 mm. Find the number of bolts required at the joint. Assume bolt diameter = 16 mm, grade of bolt = 4.6, $\gamma_{mb}$ = 1.25, $k_b$ = 0.6, cross-sectional area at the threaded part of the bolt = 0.78 times that of shank. Use limit state method of design.
- The given figure shows the shear force diagram for a beam $ABCDEF$. The beam has hinge support at $A$ and at one more point. Draw the load diagram and bending moment diagram (BMD) for this beam, indicating the shape of BMD between two successive points. Also show the point of contraflexure (if any) :
[Figure]
Shear force diagram: spans $A$-$B$ 4 m, $B$-$C$ 3 m, $C$-$D$ 2 m, $D$-$E$ 2 m... as printed: $AB$ = 4 m, $BD$ = 3 m (with $C$ at its start), $DE$ = 2 m, $EF$ = 2 m. Ordinates: 10 kN at $A$ (below axis), 2 kN (above axis from $B$ to $D$ region), 7 kN upward arrow at $E$, 2 kN at $F$ (below axis).
- A reinforced concrete passenger shelter is to be constructed as shown in the figure. The thickness of the slab is 150 mm. The ceiling plaster and roof finish load is 1.5 kN/m$^2$. The roof is inaccessible. Design and detail the slab only. Use M20 grade concrete and Fe500 grade steel. Use limit state method. Given :
| $\dfrac{M_u}{bd^2}$ | 0.3 | 0.4 | 0.5 | 0.6 | 0.7 | 0.8 | 0.9 | 1.0 |
|---|---|---|---|---|---|---|---|---|
| $p_t$ (%) | 0.07 | 0.094 | 0.119 | 0.143 | 0.168 | 0.193 | 0.219 | 0.245 |
Modification Factor vs. Percentage Tension Reinforcement graph is given below :
[Figure]
TOP PLAN: slab 1500 mm + 250 mm beam + 1500 mm wide, with beam and column, 1000 mm, 2000 mm and 1000 mm along the length; VIEW AA: 150 mm thickness slab, beam, column. Graph: modification factor (0.4 to 2.0) against percentage tension reinforcement (0 to 3.0) for $f_s$ = 120, 145, 190, 240, 290; $f_s$ is steel stress of service loads in N/mm$^2$; $f_s = 0.58 f_y \dfrac{\text{Area of cross-section of steel required}}{\text{Area of cross-section of steel provided}}$
- Three bodies of weights 200 N, 800 N and 400 N are connected with inextensible strings, passing over the frictionless pulleys as shown in the figure. Using virtual work method, determine the force $F$ required to make the motion impending to the left. Take coefficient of friction for all the contacting surfaces as 0.30 except for the pulleys which are frictionless :
[Figure]
200 N body on a horizontal surface with force $F$ to the left, Pulley 1 at the top of a 45° incline carrying the 800 N body, Pulley 2 at the foot of the incline, 400 N body on the horizontal surface at the right.
- (i) A simply supported beam ISMB 400 @ 61.6 kg/m has an effective span of 5 m. Find the design bending strength of the beam and the intensity of u.d.l. that the beam can carry under service condition. Assume that the beam is laterally supported. The grade of the steel is E250. The class of section is plastic. For ISMB 400, $I_{zz}$ = 20458 cm$^4$, $Z_{ez}$ = 1023 cm$^3$, $Z_{pz}$ = 1176 cm$^3$. Assume $\gamma_{m0}$ = 1.1. Use limit state method of design. [10]
(ii) Develop the stiffness matrix for the beam element $AB$ with respect to the coordinates (1) and (2) as shown in the figure. Take modulus of elasticity and moment of inertia of beam section as $E$ and $I$ respectively : [10]
[Figure]
Cantilever $AB$ fixed at $A$, length $l$ = 2 m; coordinate 1 is the vertical displacement at $B$, coordinate 2 is the rotation at $B$.
- For an industrial building, a gantry girder (without lateral restraint along its span) is designed to carry an overhead travelling crane for the following data :
Centre-to-centre distance between columns (i.e., span of the gantry girder) = 7.5 m
Crane capacity = 200 kN
Self-weight of the crane girder excluding trolley = 200 kN
Self-weight of trolley, electric motor, hook, etc. = 40 kN
Minimum hook approach = 1.2 m
Distance between wheel centres = 3.5 m
Centre-to-centre distance between gantry rails (i.e., span of the crane) = 15 m
Self-weight of the rail section = 300 N/m
Yield stress of steel = 250 MPa
Data analysis provided the following information :
Total vertical design bending moment (including the bending moment due to drag), $M_z$ = 685.53 kN-m
Horizontal design bending moment (due to surge load), $M_y$ = 19.84 kN-m
Based on the analysis and other governing criteria, for the design of gantry girder, it was decided to use ISMB 600 @ 1230 N/m with a channel ISMC 300 @ 363 N/m at the top as shown in the figure :
[Figure]
Dimensions in mm: ISMC 300 channel at top, 300 wide, 7.8 thick, 90 deep; ISMB 600 below, 600 deep, web 12, bottom flange 210 wide and 20.8 thick.
The properties of the sections are as follows :
| ISMB 600 @ 1230 N/m | ISMC 300 @ 363 N/m |
|---|---|
| $A$ = 15600 mm$^2$ | $A$ = 4630 mm$^2$ |
| $t_f$ = 20.8 mm | $t_f$ = 13.6 mm |
| $t_w$ = 12 mm | $t_w$ = 7.8 mm |
| Width of flange, $B$ = 210 mm | $B$ = 90 mm |
| $I_{zz}$ = 91800 $\times$ 10$^4$ mm$^4$ | $I_{zz}$ = 6420 $\times$ 10$^4$ mm$^4$ |
| $I_{yy}$ = 2650 $\times$ 10$^4$ mm$^4$ | $I_{yy}$ = 313 $\times$ 10$^4$ mm$^4$ |
| Radius at root, $R$ = 20 mm | Centre of gravity, $C_{yy}$ = 23.5 mm |
Check the adequacy of the chosen section for the moment capacity. Assume any other data suitably.
- A free jet of water with constant cross-section area of 0.01 m$^2$ is deflected by a hinged plate of length 2.0 m, supported by a spring with spring constant $k$ = 500 N/m and uncompressed length $x_0$ = 1.0 m as shown in the figure. If the density of water is 1000 kg/m$^3$ and the deflection angle is $\theta$ = 5°, determine the jet velocity. Assume steady-state condition and neglect the weight of fluid and the weight of the plate within the control volume considered in this case :
[Figure]
Jet, Hinge, Plate at angle $\theta$, Spring with $k$ = 500 N/m and $x_0$ = 1.0 m, velocity $V$.
- The nominal flow rate of water over a weir is 2 m$^3$/s. A 1 : 10 scale model of the weir is tested in a water channel. Answer the following :
(i) What is the expected flow rate for the model?
(ii) If a force of 12 N is measured on the model, what force would be expected on the prototype?
- A venturi flume, 3.0 m wide at the entrance and 1.5 m wide at the throat, has a horizontal datum. If the depth of water at the entrance and at the throat is 0.75 m and 0.65 m respectively, calculate the theoretical discharge through the venturi flume. If a 0.2 m high streamlined hump is provided at the base so that a standing wave is formed downstream of the throat, calculate the specific energy and upstream depth for the same discharge.
- The shrinkage limit test was conducted in a laboratory and the following results were obtained :
Initial mass of saturated clay = 45.0 g
Final mass of dry clay pat = 31.2 g
Initial volume of soil in saturated state = 24.8 cc
Final volume of dry clay pat = 16.1 cc
Determine the following properties of the soil, if the soil is at water content of 28.5% :
(i) Shrinkage limit
(ii) Shrinkage ratio
(iii) Specific gravity of soil solids
(iv) Maximum volumetric shrinkage
(v) Linear shrinkage
- An RCC pile of 15 m overall length is driven into a deep stratum of soft clay with unconfined compressive strength of 40 kPa. The diameter of the pile is 300 mm. Determine the safe load which can be carried by the pile. Assume factor of safety as 2.5 and adhesion factor as 0.85.
If the weight of the pile is 27 kN, what will be the ultimate uplift capacity under undrained condition? Assume coefficient $k$ as 0.7.
- Assuming the law for the velocity distribution in the boundary layer as $\dfrac{v}{V} = 2\left(\dfrac{y}{\delta}\right) - \left(\dfrac{y}{\delta}\right)^2$, derive an expression for the thickness of boundary layer. Hence calculate the thickness of boundary layer at a point 2.5 m from the leading edge of a plate, if the size of the plate is 3.0 m long and 1.25 m wide, and it is immersed in the water moving at a velocity of 0.3 m/s. Take viscosity of water equal to 0.001 N-s/m$^2$. [Notations used in the above expression have their usual meanings]
- Water flows in a triangular channel having side slope 1 Horizontal : 1 Vertical and longitudinal slope of 0.001. Estimate whether the channel is mild, steep or critical sloped when a discharge of 0.2 m$^3$/s flows through it. Assume Manning's coefficient $n$ = 0.015. Also, determine for what range of depths, the flow will be on type 1, 2 and 3 curve.
- (i) A retaining wall 5 m high with a smooth vertical back is pushed against a soil mass. What is the total passive pressure, if the horizontal soil surface carries a uniform load of 60 kN/m$^2$? Also, determine the location of resultant thrust, where it is acting. The properties of the soil are as follows :
Effective cohesion = 35 kPa
Effective angle of shearing resistance = 20°
Bulk density = 19.5 kN/m$^3$ [10]
(ii) Discuss the effect of earthquake forces on the stability of earth dams. [10]
- The data with respect to a normally consolidated clay are as follows :
Thickness of the clay layer = 3.0 m
Initial void ratio = 0.75
Liquid limit = 50%
Effective overburden pressure on the clay layer = 130 kN/m$^2$
Increment of effective pressure on the clay layer = 50 kN/m$^2$
Secondary compression index, $C_\alpha$ = 0.02
Time for completion of primary settlement = 2.0 years
What will be the consolidation settlement of the clay layer, six years after the completion of primary consolidation settlement?
- The plan of a foundation is shown in the figure. The uniform load intensity on the soil is 100 kN/m$^2$. Determine the vertical stress increment at a depth 4 m below the point $O$, using Boussinesq's method :
[Figure]
Rectangle $ABCD$ 8 m long and 4 m wide ($A$, $B$ at top, $D$, $C$ at bottom) with a semicircle of radius 2 m on side $BC$; $O$ is the centre of the semicircle (2 m from $B$ and 2 m from $C$).
- Oil of specific gravity of 0.8 and kinematic viscosity of $1.5\times10^{-4}$ m$^2$/s is pumped at a rate of 0.015 m$^3$/s through a 150 mm diameter, 325 m long pipe. Determine the Reynolds' number, pressure drop, average shear stress at the pipe wall and power required to maintain flow under the following conditions :
(i) If the pipe is horizontal
(ii) If the pipe is inclined at 10° with the horizontal and the flow is in the upward direction
- Consolidated drained tests on clay specimens were performed and the following results were obtained :
| Specimen No. | Confining pressure (kPa) | Axial load (N) | Axial deformation (mm) | Volume change (cc) |
|---|---|---|---|---|
| 1 | 200 | 410 | 11.0 | 7.0 |
| 2 | 400 | 850 | 12.3 | 8.5 |
| 3 | 600 | 1275 | 14.6 | 10.0 |
The initial diameter and length of saturated clay sample were 38 mm and 76 mm respectively. Determine the shear parameters in terms of total stress and effective stress. Also, comment on the results obtained and its application.
- What is vibroflotation technique? The results of sieve analysis for the backfill material used in a vibroflotation project are as follows :
| IS sieve | Mass of the soil retained (g) |
|---|---|
| 4.75 mm | 9.40 |
| 2.36 mm | 54.00 |
| 1.18 mm | 78.20 |
| 600 $\mu$m | 83.10 |
| 300 $\mu$m | 86.20 |
| 150 $\mu$m | 75.30 |
| 75 $\mu$m | 13.80 |
Determine the suitability number. What would be its rating as a backfill?
- (i) A Francis turbine has a speed of 300 r.p.m. The inlet diameter of the turbine is 1.20 m and its width is 280 mm at the inlet. The vane thickness coefficient can be taken as 0.95. If at the inlet, the guide vane angle is 30° and the blade angle is 90°, determine the power produced by assuming an overall efficiency of 90%. Assume radial discharge at the outlet and take density of water as 1000 kg/m$^3$. [15]
(ii) What is the significance of curves of constant stream function (CSF)? Explain why the stream function is useful in fluid mechanics. [5]