Mains PYQs
UPSC Mains Civil Engineering paper 1 2025 questions
- Draw the free body diagram of link ABCD and determine all reaction forces acting at A, B, C and D of the assembly shown in the figure.
(All dimensions are in mm.)
[Figure]
Link ABCD with a 480 N horizontal force applied at E; vertical dimensions 40 and 80; horizontal dimensions 80, 80, 40, 40.
- A horizontal cantilever beam of length 2L has its free end attached to a vertical tie rod of length L and area 'A', which is initially unstrained. If the moment of inertia of the cantilever beam is I, determine the load taken by the tie rod when a uniformly distributed load of 'w' per unit run is placed on the inner half length of the cantilever. Modulus of elasticity for the tie rod and cantilever beam is E.
[Figure]
Cantilever D-C-B fixed at D, w/unit length on D to C (length L), C to B length L, tie rod AB of length L at B.
- Calculate the maximum bending moment at points 'C' and 'D' if the five loads of 160 kN equally spaced at 1.52 m, cross the beam from right to left.
[Figure]
Beam AB with A hinged support and B roller support; C at 7 m from A, D at 14 m from A (7 m between C and D); 5 loads of 160 kN at 1.52 m spacing; 14 m marked from D to B.
- A tie member of a truss consisting of an angle-iron section ISA 65 × 65 × 6 of Fe 410 grade, is welded to an 8 mm gusset plate. Design the weld to transmit a load equal to the full strength of the member. Assume shop welding. Take weld size as 4 mm and f_y = 250 MPa, properties of ISA 65 × 65 × 6 are :
A = 744 mm², C_z = 18.1 mm, γ_m0 = 1.1, γ_m1 = 1.25
T_db = [A_vg f_y/(√3 γ_m0) + 0.9 A_tn f_u/γ_m1] or
T_db = [0.9A_vn f_u/(√3 γ_m1) + A_tg f_y/γ_m0]
[Figure]
ISA 65 × 65 × 6 on 8 mm gusset plate; 65 mm leg; 18.1 mm centroid distance.
- The plan of a ground floor column in a building is shown in the figure. It is desired to reduce the longitudinal bar diameter from 30 mm to 20 mm above the second floor level. Design and detail a suitable lap splice. Assume M25 grade concrete and Fe 500 grade steel.
[Figure]
600 mm × 300 mm column; 8 φ ties @ 200 c/c; 30 φ (6 Nos) below second floor; 20 φ (6 Nos) above second floor.
- A T-section beam is constructed by gluing two pieces of wood together as shown in the figure. The maximum stress in the glue joints is to be limited to 2 MPa in tension and maximum shear stress is to be limited to 1.7 MPa.
(i) Determine the stress components on element at point 'P'. Point 'P' is located at glued joint.
(ii) Determine principal stresses at point 'P'.
(iii) Show these stresses on properly oriented 2-D elements.
(iv) Determine the maximum value for load 'w'.
[Figure]
(a) Simply supported beam AB, span 2 m, UDL w (N/m) and moment 4w (N-m) at A. (b) T-section: web 50 mm wide, 150 mm high; flange 150 mm wide, 50 mm thick; P at the glued joint.
- For the beam shown in the figure, find the reaction at C and draw the bending moment diagram for the beam.
Take EI = Constant.
[Figure]
Beam AB fixed at both ends A and B, hinge at C at mid-span, each half length L, UDL w/unit length over AC.
- For the column section shown in the figure, determine the design strength components corresponding to the condition of 'balanced failure'. Assume M25 grade concrete and Fe 500 grade steel. Consider loading eccentricity with respect to the major axis alone. Assume 8 φ ties and 40 mm clear cover. Take E_s = 2 × 10^5 N/mm².
For Fe 500 steel ε_y = 0.87 f_y / E_s + 0.002
C_c = resultant force in concrete
C_s = Σ_{i=1}^{n} (f_si − f_ci) A_si
M_c = C_c (D/2 − X̄)
M_s = Σ_{i=1}^{n} (f_si − f_ci) A_si × y_i
A_si → Area of steel in i-th row
y_i → Distance of i-th row of steel from the centroidal axis
Design stress at specified strains for Fe 500 :
| Strain | Stress (MPa) |
|---|---|
| 0.000 | 0.0 |
| 0.00174 | 347.8 |
| 0.00195 | 369.6 |
| 0.00226 | 391.3 |
| 0.00277 | 413.0 |
| 0.00312 | 423.9 |
| 0.00417 | 434.8 |
[Figure]
Column section 500 × 300 with 8 φ ties and 6 - 25 φ bars.
- Analyse the continuous beam shown in the figure by slope-deflection method. Draw the Shear Force Diagram (SFD) and Bending Moment Diagram (BMD). Also calculate point of contraflexure in BMD.
[Figure]
Beam A-B-C, A and C fixed, B simple support; 4 kN load at 2 m from A (2 m to B); span BC 6 m; EI = constant.
- A simply supported reinforced concrete beam of size 300 × 500 mm (effective) is reinforced with 4 bars of 16 mm φ of Fe 500 grade steel. Determine the anchorage length of the bars at simply supported end if it is subjected to a factored shear force of 350 kN at the centre of 300 mm wide masonry support. The concrete mix of grade M25 is to be used.
Bond stress (τ_bd) for plain bar for M25 = 1.4 MPa
E_s = 2 × 10^5 N/mm²
- A tension member consists of two angle-irons, back to back, of size ISA 75 × 75 × 8 and is connected to the same side of a gusset plate by a single row of six 20 mm diameter bolts as shown in the figure. Calculate the load carrying capacity when the two angles are tack-bolted.
Yield stress of steel (f_y) = 250 MPa and
Ultimate tensile stress (f_u) = 410 MPa.
[Figure]
Figure (a): section with gusset plate, tacking bolts, dimensions 22, 40, 35, 75, 75, 8. Figure (b): six bolts in a row, L_c = 250, spacing 35, 50, 50, 50, 50, 50, end 35.
Given :
β = 1.4 − 0.076 (w/t)(f_y/f_u)(b_s/L_c) ≤ (f_u γ_m0)/(f_y γ_m1), ≥ 0.7
where, w = outstand leg width
b_s = shear lag width
L_c = length of the end connection
α = 0.6 for one or two bolts
α = 0.7 for three bolts
α = 0.8 for four or more bolts
- Analyse the frame shown in the figure by the moment distribution method. Draw the Bending Moment Diagram (BMD). Joints 'B' and 'C' are rigid; 'A' and 'D' are fixed.
[Figure]
Portal frame ABCD: 40 kN load on BC at 2 m from B and 3 m from C; BC has 2I; columns AB and CD, each 3 m high, have I.
- A horizontal steel bar of 60 mm diameter is rigidly tied at each end, the ties being 1.25 m apart. A rigid bracket is fixed to the middle of the bar. Determine the maximum radial length of the bracket at which a vertical load of 1400 N can be suspended, if the deflection of the load is not to exceed 0.5 mm. Take E = 2 × 10^5 N/mm²; G = 7.6 × 10^4 N/mm².
- (i) For a continuous beam ABCDEFG, show the pattern of loading for the live load for the following :
(A) max −ve bending moment at support C
(B) max +ve bending moment in span CD
(C) max −ve bending moment in span CD
(D) max +ve bending moment at support C [6]
(ii) Design a (tread and riser) dog-legged staircase of an office building, given the following data :
Height between floors = 3.2 m
Riser = 160 mm
Tread = 270 mm
Width of flight = Landing width = 1.25 m
Live load = 5 kN/m²
Finishes load = 0.6 kN/m²
Consider the landing to be supported only on two edges perpendicular to the risers.
Take density of concrete = 25 kN/m³.
P_t/100 = A_st/bd = (f_ck/2f_y) [1 − √(1 − 4.598 R/f_ck)] where R = M_u/bd².
[Figure]
Plan of staircase: 2600 overall width; 625, 625, 2430, 625, 625 horizontal; 1250, 100, 1250 flight and gap. [14]
- A rigid body having dimensions of 0.6 m wide, 0.9 m high and 1.2 m long weighs 10 kN when submerged in water.
What will be its weight and density in air ?
(Assume specific weight of water as 9790 N/m³.)
- With neat sketches explain Hydrodynamically smooth surface, Hydrodynamically rough surface and Boundary layer separation.
What are the effects of separation in a fluid flow problem ?
- A Kaplan turbine develops 20,000 kW power at a head of 40 m.
The diameter of the boss is 0.4 times the diameter of the runner.
Calculate :
(i) Diameter of the runner
(ii) Rotational speed of the turbine
(iii) Specific speed of the turbine
(Assume a speed ratio of 2.5, flow ratio of 0.80 and an overall efficiency of 80%.)
- In a laboratory, the liquid limit test by Casagrande's apparatus is performed and following results are obtained :
| Test No. | 1 | 2 | 3 | 4 |
|---|---|---|---|---|
| Moisture Content (%) | 68 | 58 | 50 | 45 |
| No. of blows | 4 | 9 | 28 | 46 |
The plastic limit of the soil is 27%. Draw the flow curve and find flow index. Also classify the soil.
- The unconfined compressive strength of a saturated clay is 90 kN/m². Determine the net ultimate bearing capacity of a square footing of side 0.75 m, resting on the surface of the saturated clay. What will be the safe bearing capacity if factor of safety is 2.5 ?
- The discharge Q over a small rectangular weir depends on head H over the weir, the weir height P, gravity g, width of the weir L and fluid properties : density ρ, dynamic viscosity μ.
Express the relationship between the variables in dimensionless form using Buckingham method.
- A rectangular channel is 4.0 m wide and carries a discharge of 5.0 m³/s at a depth of 1.0 m. A smooth contraction of the channel width is proposed at a section. Find the smallest contracted width that will not affect the upstream flow conditions. Neglect the energy losses in the transition.
- (i) In the given diagram, the height of a retaining wall is 5 m with a batter angle 6°. The back face of the retaining wall is supporting a sandy soil, the surface of which is sloping at an angle 12° with the horizontal. Determine the active force per unit length of the retaining wall. Also find the direction and location of the resultant force. The properties of backfill soil are as below :
Angle of shearing resistance = 32°
Cohesion = 0
Assume angle of wall friction as 50% of angle of shearing resistance.
Bulk density = 15.5 kN/m³
[Figure]
Retaining wall 5 m high, batter angle 6°, backfill slope 12°. [15]
(ii) What is the effect of earthquake on lateral earth pressure against a retaining wall ? [5]
- A braced cut 7.0 m deep and 3.0 m wide is proposed in a cohesionless sand deposit. Assume that the first row of struts to be located at 0.5 m below ground level and the spacing of strut as 2.5 m as shown in the diagram. In the plan, the struts are placed at spacing of 2 m centre to centre. Using Peck's empirical relation for pressure diagram, determine the design loads in the struts. The properties of sand are as follows :
Angle of shearing resistance = 30°
Bulk density = 16.5 kN/m³
[Figure]
Braced cut 3.0 m wide; struts A, B, C at 0.5 m, then 2.5 m, 2.5 m, and 1.5 m to the bottom.
- A 5 m thick clay layer is subjected to drained condition both at top and bottom. It has few sand drains in square pattern. The spacing of sand drains are 3 m centre to centre. The coefficient of consolidation in vertical and radial directions are same and equal to 5 × 10^-3 m²/day. The radius of the sand drains is 0.25 m. Assuming that there is no smear at the periphery of drain wells, it has been estimated that a given uniform surcharge would cause a total consolidation settlement of 200 mm without sand drains. Find the consolidation settlement of clay layer with same surcharge and sand drains, at times of 6 months, 9 months and one year. Draw the variation of settlement with time.
- (i) A liquid whose specific gravity is 0.8 and dynamic viscosity is 1.8 poise, flows in a vertical pipe of 8 cm diameter. Pressure gauges in the pipe located 20 m apart indicate a pressure of 180 kPa at the upper end and a pressure of 360 kPa at the lower end.
Calculate the flow rate and find the direction of the flow in the pipe. (Use Hagen-Poiseuille equation.) [10]
(ii) Water flows from A to B through a tapering pipe. The following data is given at section A and B :
| Section | A | B |
|---|---|---|
| Diameter of pipe | 12 cm | 10 cm |
| Elevation | 100.000 m | 101.000 m |
| Gauge pressure | 30 kPa | 20 kPa |
Estimate the discharge in the pipe line.
(Assume zero loss of energy between two sections.) [10]
- The consolidated undrained (CU) tests were performed on the four over-consolidated clay samples obtained from a site. The pre-consolidation pressure was 650 kN/m². The results of triaxial test in CU condition are as follows :
| Test sample | Cell pressure kN/m² | Deviator stress kN/m² | Pore pressure kN/m² | Remark |
|---|---|---|---|---|
| 1 | 100 | 290 | −40 | All the tests were performed in CU condition. The deviator stress and pore pressure were at failure. |
| 2 | 200 | 430 | −20 | |
| 3 | 400 | 600 | 50 | |
| 4 | 600 | 840 | 110 | |
Determine the effective shear strength parameters. Draw the variation of pore pressure parameter 'A' (at failure) with over-consolidation ratio.
- A 250 mm diameter concrete pile 8 m long was driven by a double-acting hammer. The driving was carried out by a short dolly and cushion. The average penetration recorded in the last five blows was 3.0 mm per blow. Determine the safe pile load. As per IS 2911 (Part I) – 1979, the coefficient of restitution of the materials under impact for double-acting hammer striking on steel anvil and driving RCC pile is 0.5. The rated energy of hammer is 16.5 kJ and mass of hammer is 22 kN. Assume that only 90% of the rated energy is consumed. The density of RCC pile may be considered as 25 kN/m³. Assume the factor of safety as 2.5.
- (i) In a horizontal, rectangular channel, the sluice gate is opened. A hydraulic jump is formed downstream of the sluice gate.
The depth of water before jump is 0.8 m and specific energy before jump is 12.0 m.
Find the sequent depth of the jump and energy lost in the jump. What is the initial Froude number ? Classify the jump based on the results obtained in the problem. [10]
(ii) A runoff river plant is proposed to generate hydroelectric power. The net head available is 30 m. The river carries a sustainable flow of 30 m³/s in dry weather. Determine the maximum generating capacity. Daily load pattern indicates 20 hrs of average load and 4 hrs of peak load. Estimate the volume of pondage to be provided to supply the daily demand.
Assume load factor = 85%, Efficiency = 80%. [10]