Mains PYQs
UPSC Mains Civil Engineering paper 1 2022 questions
- A rod shown in the figure below is subjected to a force of 95 kN. Determine the diameter $d$ of the portion (2), if the stress there is not to exceed $115\,\mathrm{N/mm^2}$. Also, determine the axial deformation of the rod. Use $E = 205$ GPa :
[Figure]
Portions: (1) 50 mm dia, 100 mm long; (2) dia $d$, 50 mm long; (3) 85 mm dia, 100 mm long; (4) 50 mm dia, 50 mm long; 95 kN pull at each end.
- A reinforced concrete beam of $250\,\mathrm{mm} \times 500\,\mathrm{mm}$ is reinforced with 3 nos. 16 mm dia bars as tension reinforcement. The nominal cover to the reinforcement is 30 mm and diameter of stirrups is 8 mm. Calculate the moment of resistance of the beam. Use M20 and Fe500. Adopt limit state method of design.
- A three-hinged parabolic arch of uniform cross-section has a span of 60 m and a central rise of 10 m. It is subjected to a UDL of intensity 15 kN/m covering the whole span. Show that the bending moment is zero at any cross-section of the arch.
- Use Castigliano's theorems and determine the vertical displacement of point $C$ of the beam shown in the figure below. Take $E = 210$ GPa and $I = 150 \times 10^6\,\mathrm{mm^4}$ :
[Figure]
Beam $AB$: 25 kN point load at $C$, 3 m from $A$; 10 kN/m UDL over the 4 m from $C$ to $B$.
- A vertical member of a truss consisting of an angle section ISA $75 \times 75 \times 8$ of E250 grade is welded to a 10 mm thick gusset plate. The factored tensile and compressive forces in the member are 100 kN and 90 kN respectively. Design the weld connection (shop weld) having weld size of 4 mm; only two sides of the angle are welded. $C_y = C_z = 21.4\,\mathrm{mm}$ for ISA $75 \times 75 \times 8$.
- Determine the forces in all the members of a pin-jointed truss shown in the figure below, with a vertical force of 20 kN and a horizontal force of 10 kN acting at $C$ :
[Figure]
$C$ is the apex, $D$ is 2 m below $C$, $A$ and $B$ are supports 4 m below $C$ and 3 m either side horizontally; 20 kN acts downward and 10 kN horizontally at $C$.
- A 3 m high square column is effectively held in position but not restrained against rotation at both ends. The size of the column is restricted to 400 mm. Design and detail the column to carry a factored axial load of 2000 kN. Use M25 grade of concrete and Fe500 grade of steel. Use limit state method.
- A solid circular shaft is subjected to a bending moment of $10 \times 10^3\,\mathrm{N\text{-}m}$ and a twisting moment of 13 kN-m. In a simple uniaxial tensile test of the same material, it gave the following data :
$\sigma_y = 300\,\mathrm{N/mm^2}$, $E = 200 \times 10^3\,\mathrm{N/mm^2}$
Factor of safety (FOS) = 3, $\nu = 0.25$
Determine the least diameter required using the following :
(i) Maximum principal stress theory
(ii) Maximum shear stress theory
- (i) A simple girder of 20 m span is traversed by a moving uniformly distributed load of 6 m long with an intensity of 2 kN/m, from left to right. Determine the maximum bending moment and shear force at 4 m distant section from the left support. Also, determine the absolute maximum bending moment that may occur anywhere in the girder. [10]
(ii) Determine the maximum force that can be developed in member $BC$ of the bridge truss shown in the figure below due to a moving load of $80 \times 10^3\,\mathrm{N}$ and a moving uniformly distributed load of $8.50\,\mathrm{kN/m}$. The loading is applied at the top chord :
[Figure]
Pratt-type truss, bottom chord $A$-$B$-$C$-$D$-$E$, top chord $J$-$I$-$H$-$G$-$F$, 4 panels of 8 m each, height 6 m. [10]
- A laced column of height 8 m is made of 2 nos. ISMC 350 placed back-to-back. The column is restrained against translation and free against rotation at both ends in both directions. Find the distance between them to carry maximum axial compressive force and calculate the factored load-carrying capacity of the column using limit state method. The properties of ISMC 350 are $A = 5440\,\mathrm{mm^2}$, $I_{zz} = 10000\,\mathrm{cm^4}$, $I_{yy} = 434\,\mathrm{cm^4}$, $C_y = 24.4\,\mathrm{mm}$.
Given :
| $KL/r$ | 20 | 30 | 40 | 50 | 60 | 70 | 80 | 90 | 100 |
|---|---|---|---|---|---|---|---|---|---|
| $f_{cd}$ (MPa) | 224 | 221 | 198 | 183 | 168 | 152 | 136 | 121 | 107 |
| $KL/r$ | 110 | 120 | 130 | 140 | 150 | 160 | 170 | 180 |
|---|---|---|---|---|---|---|---|---|
| $f_{cd}$ (MPa) | 95 | 84 | 74 | 66 | 59 | 53 | 48 | 44 |
- A post-tensioned simply supported beam of 300 mm wide $\times$ 600 mm depth spans over 10 m and carries a live load of 7 kN/m. The total area of cables is $500\,\mathrm{mm^2}$ and located at 100 mm from the soffit of the beam. The initial prestress in the cables is 1400 MPa. Compute the net initial and final concrete stresses in the extreme top and bottom fibres at midspan of the beam. Assume loss of prestress = 15%.
- Find the maximum load $P$, which the bracket as shown can transmit. The bolt strength of 20 mm dia and 8.8 grade is assumed to be 82 kN, considering shear and bearing under limit state method :
[Figure]
Bracket with six bolts in two vertical lines of three (spacing 50 mm vertically, 50 mm either side of the centre line horizontally); load $P$ acts 400 mm from the bolt group.
- A continuous beam $ABC$ has span $AB = 6$ m and $BC = 6$ m and carries a uniformly distributed load of 25 kN/m covering both the spans $AB$ and $BC$. Supports $A$ and $C$ are simple supports. If the load factor is 1.75 and the shape factor is 1.144 for the I-section, determine the section modulus required. Use the yield stress for the material as 245 MPa.
- Design the vertical stem of a reinforced concrete retaining wall as shown below. The angle of repose of the earth is $30^\circ$ and its density is $18\,\mathrm{kN/m^3}$. Use M25 grade of concrete and Fe500 grade of steel. The wall is safe against stability. Detail the reinforcement in the stem only :
[Figure]
Stem retains 3 m of earth above the top of the base slab level on the backfill side; EGL on toe side is 1 m above the base; base slab 400 mm thick; toe 700 mm, stem 250 mm, heel 1300 mm.
Given :
| $M_u/bd^2$ | 1.5 | 1.6 | 1.7 | 1.8 | 1.9 | 2.0 | 2.1 | 2.2 | 2.3 | 2.4 | 2.5 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| $p_t$ | 0.373 | 0.40 | 0.427 | 0.455 | 0.484 | 0.512 | 0.541 | 0.571 | 0.601 | 0.631 | 0.662 |
Assume nominal cover to reinforcement as 50 mm. Curtailment of bars is not required.
Given :
| $\tau_c$ (MPa) | 0.36 | 0.49 | 0.57 | 0.64 | 0.70 | 0.74 | 0.78 | 0.82 | 0.85 | 0.88 |
|---|---|---|---|---|---|---|---|---|---|---|
| $p_t$ | 0.25 | 0.5 | 0.75 | 1.0 | 1.25 | 1.5 | 1.75 | 2.0 | 2.25 | 2.5 |
- Prove that the power transmission through nozzle is maximum when $\dfrac{d}{D} = \sqrt{\dfrac{D}{8fl}}$. Neglect the minor losses.
[Figure]
Diameter $D$ pipe of length $l$, ending in a nozzle of diameter $d$; $f$ = Friction coefficient
- Soil from a particular site yields a maximum dry unit weight of $18\,\mathrm{kN/m^3}$ at an optimum moisture content of 16% during a standard Proctor test. If the value of $G$ is 2.65, what is the degree of saturation? What is the maximum dry unit weight, it can be further compacted to? Take the unit weight of water as $9.81\,\mathrm{kN/m^3}$.
- Draw the possible gradually varied flow profiles for critical slope. Indicate very clearly the boundary conditions.
- In a fluid machine, the torque $T$ of the impeller is known to depend on the diameter $D$ and speed $N$ of the impeller, the density $\rho$ and dynamic viscosity $\mu$ of the fluid. Obtain the relationship in a dimensionless form using Buckingham method. Specify the use of non-dimension numbers in design problems.
- A $2\,\mathrm{m} \times 2\,\mathrm{m}$ square footing is founded at a depth of 0.8 m in a homogeneous bed of sand having a unit weight of $19\,\mathrm{kN/m^3}$ and an angle of shearing resistance of $38^\circ$. Assuming the water table to be at a great depth, compute the safe load that can be carried by the footing. Use Terzaghi's theory and assume a factor of safety of 3. For $\phi = 38^\circ$, take $N_q = 65$ and $N_\gamma = 80$.
- The velocity profile in a laminar boundary layer on a flat plate is modelled by the cubic expression
$$\frac{\mu}{\mu_1} = a_0 + a_1 y + a_2 y^2 + a_3 y^3$$
$\mu$ = velocity at a distance $y$ from the surface of the plate
$\mu_1$ = main stream velocity
Evaluate all the constants in terms of boundary layer thickness. Draw the velocity distribution and stress distribution curves. Indicate the application and significance of boundary layer. If the plate is moving with a velocity of 2 m/s in positive $x$-direction, what will be the velocity distribution curve?
- Plot the variations of (i) total pressure, (ii) neutral stress and (iii) effective stress for a fine sand deposit, having a porosity of 40% and specific gravity of 2.7, extending to a depth of 10 m below the ground surface. The groundwater table is 5 m below the ground surface and the sand is saturated by capillary water up to a height of 1 m above the water table. The degree of saturation of the first 4 m of moist soil below the ground surface is 10%. Take the unit weight of water as $10\,\mathrm{kN/m^3}$.
- Reservoir $A$ (elevation 65 m) is filling reservoir $B$ (elevation 110 m) and reservoir $C$ (elevation 90 m) by a pump and pipe system. The discharge to reservoir $C$ is $0.10\,\mathrm{m^3/s}$. If the efficiency of the pump is 0.70, calculate the required power of the pump. The physical characteristics of the pipe system are given in the figure below. Neglect the minor losses. Draw the HGL and EGL :
[Figure]
Pipe from $A$ to the junction (pump): $l = 400$ m, $d = 30$ cm, $f = 0.02$; pipe from junction to $B$: $l = 300$ m, $d = 15$ cm, $f = 0.015$; pipe from junction to $C$: $l = 1000$ m, $d = 20$ cm, $f = 0.025$; elevations above the reference datum: $A$ 65 m, $B$ 110 m, $C$ 90 m.
- (i) Distinguish between discharge velocity and seepage velocity in the case of flow of water through soils. [5]
(ii) A soil sample 90 mm high and $6000\,\mathrm{mm^2}$ in cross-section was subjected to a falling head permeability test. The head fell from 500 mm to 300 mm in 1500 seconds. The permeability of the soil was $2.4 \times 10^{-3}\,\mathrm{mm/s}$. Determine the diameter of the standpipe. [10]
- Two parallel plates are moving in opposite direction with velocities 1 m/s and 2 m/s respectively. For the given coordinate system (shown below), draw the velocity and shear stress profile for positive and negative pressure gradient after obtaining the profile equations :
[Figure]
Plate 1 (top) moves with $V = 1\,\mathrm{m/s}$ in the $+x$ direction; Plate 2 (bottom) moves at 2 m/s in the $-x$ direction; the $x$ axis lies midway, at $B/2$ from each plate; $y$ is vertical.
- Laboratory results of a soil have shown that its unconfined compressive strength is $120\,\mathrm{kN/m^2}$. In a triaxial compression test, a specimen of the soil when subjected to a confining pressure of $40\,\mathrm{kN/m^2}$ failed at an additional stress of $160\,\mathrm{kN/m^2}$. Estimate the shearing strength of the same soil along a horizontal plane at a depth of 4 m at the site. The groundwater table is at a depth of 2.5 m from the ground level. Take the dry unit weight of the soil as $17\,\mathrm{kN/m^3}$ and specific gravity as 2.7. Also, assume the unit weight of water as $10\,\mathrm{kN/m^3}$.
- A vertical cut, 4.5 m deep, is to be made in a $c$-$\phi$ soil having cohesion $= 19.1\,\mathrm{kN/m^2}$, angle of internal friction $= 16^\circ$ and unit weight $= 18.5\,\mathrm{kN/m^3}$. Compute the following :
(i) The active earth pressure at the top and bottom of the cut
(ii) The depth up to which the tension cracks develop
(iii) The maximum depth of excavation that can be left unsupported
- A vertical sluice gate with an opening of 0.60 m produces a downstream jet with a depth of 0.40 m when installed in a long rectangular channel, 5.0 m wide, conveying a steady discharge of $20\,\mathrm{m^3/s}$. It is observed that the flow, downstream of the gate eventually returns to a uniform depth of 2.5 m. Indicate whether jump will occur or not. Justify the answer. Calculate the following :
(i) Energy head loss
(ii) Upstream depth
(iii) Force on the gate
Briefly explain the applications of hydraulic jump. Can we apply critical energy concept in case of hydraulic jump? Justify your answer.
- The following data was obtained from a plate load test carried out on a 60 cm square test plate at a depth of 2 m below the ground surface on a sandy soil with water table at a great depth :
| Load intensity ($\mathrm{kN/m^2}$) | 0 | 50 | 100 | 150 | 200 | 250 | 300 |
|---|---|---|---|---|---|---|---|
| Settlement (mm) | 0 | 2.0 | 4.0 | 7.5 | 11.0 | 16.3 | 23.5 |
Determine the settlement of a $3\,\mathrm{m} \times 3\,\mathrm{m}$ square footing founded at a depth of 2 m below the ground surface, carrying a load of 1100 kN, and compare this settlement with the permissible settlement specified by the Indian Standards.