Mains PYQs
UPSC Mains Civil Engineering paper 1 2021 questions
- Determine the forces in members AC, DE and GH of the truss loaded and supported as shown in the figure below :
[Figure]
Labels: loads 5 kN at A, 10 kN at C, 10 kN at D, 10 kN at G, 5 kN at H; panel spacing 2 m each (A-C, C-D, D-G, G-H); depth 2 m; bottom joints B, E, F; hinge at A, roller at H.
- A prestressed concrete beam of section 160 mm wide by 400 mm deep is used over an effective span of 8 m to support a uniformly distributed load of 5 kN/m which includes the self-weight of the beam. The beam is prestressed by a straight cable carrying a force of 200 kN and located at 100 mm above the bottom of the beam.
Determine the resultant stresses at the centre of the span sections at top and bottom fibres of the beam.
- A bracket plate of thickness 12 mm is connected perpendicular to the flange of a column (ISMB 400). Design a connection for the bracket using the fillet weld to carry a vertical load of 200 kN acting at 250 mm from the face of the column. The grade of steel is E 250. Assume shop welding. Take ultimate stress of weld material, $f_u$ = 410 MPa.
- A space 25 mm wide between two large plane surfaces is filled with glycerine. What force is required to drag a very thin plate 0.75 $\mathrm{m^2}$ in area between the surfaces at a speed of 0.5 m/s :
(i) if this plate remains equidistant from the two surfaces,
(ii) if it is at a distance of 10 mm from one of the surfaces ?
Take dynamic viscosity of glycerine $\mu$ = 0.785 $\mathrm{N\text{-}s/m^2}$.
- A field density test of a soil was performed by digging a small hole in the soil, weighing the extracted soil and measuring the volume of the hole. The soil (moist) weighed 895 g, the volume of the hole was 426 $\mathrm{cm^3}$. After drying the sample weighed 779 g. From the dried soil, 400 g was poured into a vessel in a very loose state which occupied a volume of 276 $\mathrm{cm^3}$. The same 400 g was then vibrated and tamped to a volume of 212 $\mathrm{cm^3}$. Determine the relative density of the field soil.
Given : Specific gravity of solids, $G_s$ = 2.70 and unit weight of water, $\gamma_w$ = 9.81 $\mathrm{kN/m^3}$.
- Using moment area method, find the slopes and deflection at 'B' for the beam shown in the figure below. Point 'B' is a hinge.
[Figure]
Labels: fixed support at A, hinge at B, load W at C, roller support at D; spans A-B, B-C, C-D each L.
- A rectangular reinforced concrete column of size 250 mm $\times$ 400 mm is used to support an ultimate axial load of 700 kN. The column has an unsupported length of 3.2 m. The column is effectively held in position at both ends and restrained against rotation at one end.
Design suitable reinforcements in the column using M 25 grade of concrete and Fe 415 HYSD bars. Also draw the reinforcement details. Use limit state method.
- A flow of 100 litres/sec flows down in a rectangular laboratory flume of width 0.60 m and having adjustable bottom slope. If Chezy's constant (C) is 56, determine the bottom slope for uniform flow with a depth of flow 0.30 m. Also find the conveyance and state the flow.
- The figure below represents time and consolidation relationship for a clay sample 30 mm thick subjected to a given pressure range under double drainage condition.
Determine :
(i) The coefficient of consolidation ($C_v$) for the sample.
(ii) The time required for 75% consolidation of the same clay soil, if it were 2 m thick with similar drainage condition.
(iii) The time required for same degree of consolidation with single drainage condition.
Given :
$T = \frac{\pi}{4}U^2$ for $U < 60\%$
$T = (-)\,0.933\log_{10}(1-U) - 0.085$ for $U > 60\%$
[Figure]
Labels: Strain vs $\sqrt{\text{Time}}$ ($\sqrt{\text{min}}$), axis 0 to 9; Percent consolidation 0 to 100; construction lengths b, 1.15 b, a, 1.15 a.
- A single angle strut ISA 80 $\times$ 80 $\times$ 10 is used to carry a service load of 80 kN. The centre to centre distance between the end connections is 2 m. The end connection is done by two bolts. Check the adequacy of the section to carry this load.
The grade of steel is E 250. Use limit state method.
Take $K_1$ = 0.2, $K_2$ = 0.35 and $K_3$ = 20 for 'fixed' fixity as per code IS 800 : 2007.
Properties of ISA 80 $\times$ 80 $\times$ 10
A = 1500 $\mathrm{mm^2}$
$r_y$ = 24.1 mm
$r_z$ = 24.1 mm
$r_{uu}$ = 30.4 mm
$r_{vv}$ = 15.5 mm
- A conical draft tube having inlet and outlet diameters 1 m and 1.5 m discharges water at outlet with a velocity of 2.5 m/s. The total length of the draft tube is 6 m and 1.2 m of the length of draft tube is immersed in water. If the atmospheric pressure head is 10.3 m of water and loss of head due to friction in the draft tube is equal to 0.20 times the velocity head at outlet of the tube, find :
(i) Pressure head at inlet
(ii) Efficiency of draft tube
- Determine the maximum tensile force in member DI of the truss shown below due to the series of three moving loads shown in the figure.
Support : Hinge at 'A' and Roller at 'G'. Loads move from G to A.
[Figure]
Labels: truss with top chord A, B, C, D, E, F, G and bottom chord H, I, J, K, L; 6 panels at 4 m = 24 m; height 3 m. Moving loads 125 kN, 100 kN, 50 kN spaced 2 m and 3 m.
- Two parallel plates kept 0.10 m apart have laminar flow of oil between them with a maximum velocity of 1.5 m/s.
Calculate the discharge per metre width, the shear stress at the plates, the difference in pressure between two points 20 m apart, the velocity gradients at the plates and velocity at 0.02 m from the plate.
Take viscosity of oil to be 2.453 $\mathrm{N\text{-}s/m^2}$.
- Investigate the stability against overturning, sliding resistance and foundation soil pressure of the retaining wall shown in the figure. The retaining wall is to support a deposit of granular soil which has unit weight, $\gamma$ = 17.5 $\mathrm{kN/m^3}$ and angle of internal friction, $\phi$ = 35$^\circ$. The coefficient of base friction is 0.5. Allowable soil pressure for the foundation soil is 150 kPa. Use Rankine's theory to calculate the active earth pressure on the wall and neglect passive pressure from the toe side.
Given : Unit weight of concrete, $\gamma_c$ = 24 $\mathrm{kN/m^3}$.
[Figure]
Labels: wall top width 1 m, base width 3 m, height 6 m; granular backfill $\gamma$ = 17.5 $\mathrm{kN/m^3}$, $\phi$ = 35$^\circ$, C = 0; wall $\gamma_c$ = 24 $\mathrm{kN/m^3}$.
- A circular log of weight 1000 N and radius 18 cm is supported by a pair of brackets, one of which is shown in the figure below. Bar PN is hinged at 'P' and held by a string MN 67 cm long. To induce minimum tension at MN, determine the value of $2\theta$, as shown for equilibrium.
Consider all contact surfaces smooth. Also find the value of minimum tension.
[Figure]
Labels: vertical wall through M, Q, P; horizontal string MN; bar PN hinged at P; circle with centre G touching wall at Q and bar at J; angle $\theta$ on each side of PG.
- Determine the moment of resistance of the T-beam as shown in the figure. Use limit state method.
[Figure]
Labels: flange width 1000 mm, flange depth 100 mm, overall depth 400 mm (as labelled), web width 300 mm, 4 nos 25 $\phi$ bar, 50 mm cover from bottom.
Take M 20 grade of concrete and Fe 415 HYSD bars.
- The fixed-end bar ABCD consists of three prismatic segments as shown in the figure. The end segments AB and CD have cross-sectional area 800 $\mathrm{mm^2}$ and length 300 mm. The middle segment has cross-sectional area 1200 $\mathrm{mm^2}$ and length 500 mm. Two axial loads $P_B$ = 28.5 kN and $P_C$ = 20 kN are acting in the bar as shown in the figure. Young modulus E is same for all three segments.
(i) Determine the reaction forces at fixed supports.
(ii) Determine the compressive axial force in the middle segment.
[Figure]
Labels: A and D fixed ends; segment lengths 300 mm, 500 mm, 300 mm; $P_B$ at B acting toward C, $P_C$ at C acting toward B.
- A flow meter when tested in a laboratory gives a pressure drop of 100 $\mathrm{kN/m^2}$ for a discharge of 0.10 $\mathrm{m^3/s}$ in a 150 mm diameter pipe. If a geometrically similar model is tested in 600 mm diameter pipe at identical conditions of fluid, determine the corresponding discharge and pressure drop in the model.
- A sample of dry cohesionless soil whose angle of internal friction is 35$^\circ$, is subjected to a triaxial test. If the minor principal stress ($\sigma_3$) is 105 kPa, at what values of deviator stress ($\Delta\sigma$) and major principal stress ($\sigma_1$) will the test specimen fail ?
- A submarine can be assumed to have cylindrical shape with rounded nose. Assuming its length to be 55 m and diameter 6.0 m, determine the total power required to overcome boundary friction if it propels at the velocity of 8.0 m/s in sea water at 20$^\circ$C. Take mass density of sea water at 20$^\circ$C as 1030 $\mathrm{kg/m^3}$ and kinematic viscosity of sea water at 20$^\circ$C as $1\times10^{-6}$ $\mathrm{m^2/s}$.
- For the beam shown in the figure below
(i) Compute the support reactions.
(ii) Write the shear force (V) and bending moment (M) value(s) at salient points as indicated in the table.
| x | A | B | C | D | E | F |
|---|---|---|---|---|---|---|
| V | | | | | | |
| M | | | | | | |
(iii) Draw the shear force diagram (SFD) indicating the nature of graph.
(iv) Draw the bending moment diagram (BMD) indicating the nature of graph.
Sign conventions for SFD and BMD are as follows :
[Figure]
Labels: +V (downward on left face, upward on right face), +M (anticlockwise on left face, clockwise on right face); beam A-B-C-D-E-F with 25 kN/m UDL over A to B, 300 kN-m moment at C, 50 kN at D, 40 kN at F; supports at B and E; spacings A-B 0.5 m, B-C 1 m, C-D 2 m, D-E 1.5 m, E-F 0.5 m (a further 0.5 m is printed at the right end).
- Size of a rectangular simply supported beam is restricted to 300 mm $\times$ 500 mm (overall). The effective span of the beam is 5 m. The beam is subjected to an imposed load of 64 kN/m. Design the beam using M 20 grade of concrete and Fe 415 grade of steel. Take effective cover as 40 mm and width of supporting wall as 250 mm. The stress in the reinforcement can be derived from the stress-strain curve given below. Use limit state method of design.
[Figure]
Labels: Stress-Strain Curve for Cold Worked Deformed Bar; curves $f_y$ and $f_y/1.15$; $E_s$ = 200000 $\mathrm{N/mm^2}$; stress levels 0.80 $f_y$, 0.85 $f_y$, 0.90 $f_y$, 0.95 $f_y$, 0.975 $f_y$, $f_y$; strains 0.0001, 0.0003, 0.0007, 0.001, 0.002, 0.003, 0.004.
- The subsoil at a site consists of a 12.0 m thick homogeneous layer of dense sand having dry unit weight, $\gamma_d$ = 17.2 $\mathrm{kN/m^3}$, $G_s$ = 2.7 and $\phi$ = 35$^\circ$. The natural ground water level lies at 2.5 m below the ground surface. Assume that the soil is dry above the water table and unit weight of water, $\gamma_w$ = 9.81 $\mathrm{kN/m^3}$. Determine the shear strength of the soil along a horizontal plane through the middle of the sand layer.
- A 2 m $\times$ 2 m square footing is placed at 1.8 m below the ground surface. The ground water table is at the ground level. The subsoil consists of a uniform deposit of soft, loose soil. The laboratory test results of the soil are as follows :
Angle of internal friction, $\phi$ = 21$^\circ$
Cohesion, C = 15 kPa
Unit weight of soil, $\gamma$ = 16.5 $\mathrm{kN/m^3}$
Determine the allowable load that can be imposed on this square footing with a factor of safety of 3.
Given :
| $\phi$ | $N_c$ | $N_q$ | $N_\gamma$ |
|---|---|---|---|
| 10 | 8.34 | 2.47 | 0.37 |
| 12 | 9.28 | 2.97 | 0.60 |
| 14 | 10.37 | 3.59 | 0.92 |
| 16 | 11.63 | 4.34 | 1.37 |
| 18 | 13.10 | 5.26 | 2.00 |
| 20 | 14.83 | 6.40 | 2.87 |
| 22 | 16.88 | 7.82 | 4.07 |
| 24 | 19.32 | 9.60 | 5.72 |
- A simply supported steel beam of span 4 m carries a factored point load of 450 kN at its mid span. The beam is laterally supported. Check the adequacy of ISMB 400 section to carry this load. If it becomes unsafe, re-design it by providing extra cover plate to make it safe. Assume the section is plastic. Grade of steel is E 250. Use limit state method.
Section properties of ISMB 400 :
A = 7840 $\mathrm{mm^2}$
$b_f$ = 140 mm
$t_f$ = 16 mm
$t_w$ = 8.9 mm
$Z_{pz}$ = $1176.18 \times 10^3$ $\mathrm{mm^3}$
$Z_{ez}$ = $1020 \times 10^3$ $\mathrm{mm^3}$
- A 300 mm diameter concrete pile is to be driven into a medium dense to dense sand with an embedded length of 12 m. The soil conditions are shown in the figure. No ground water was encountered and the ground water table is not expected to rise during the life of the structure.
Given : The coefficient lateral earth pressure (k) = 0.95, $\tan\delta$ = 0.45 and for $\phi$ = 38$^\circ$ bearing capacity factor, $N_q$ = 80.
Determine the pile's axial capacity with a factor of safety of 2. Assume critical depth of the pile is equal to 20 times the diameter of the pile.
[Figure]
Labels: pile length 12 m in medium dense to dense sand, $\gamma$ = 20.1 $\mathrm{kN/m^3}$, $\phi$ = 38$^\circ$, k = 0.95.
- A Pelton wheel develops 5520 kW power under a head of 240 m at an overall efficiency of 80% when revolving at a speed of 200 rpm. Find the unit discharge, unit power and unit speed. Assume peripheral coefficient as 0.46. If the head on the same turbine falls during summer season to 150 m, find the discharge, power and speed at this head.
- A 1 m long hollow shaft is to transmit a torque of 400 N-m. The outer diameter of the shaft must be 25 mm to fit existing attachments. The relative rotation of the two ends of the shaft is limited to 0.375 rad. The shaft can be made of either titanium alloy or aluminium. Using the data given in the table below, determine the maximum inner radius to the nearest millimeter of the lightest shaft that can be used for transmitting the torque.
| Material | Shear Modulus G (GPa) | Maximum Shear Stress $\tau_{allow}$ (MPa) | $\gamma$ (density) ($\mathrm{Mg/m^3}$) |
|---|---|---|---|
| Titanium alloy | 36 | 450 | 4.4 |
| Aluminium | 28 | 150 | 2.8 |
[Figure]
Labels: hollow shaft 1 m long, outer diameter 25 mm.