Mains PYQs
UPSC Mains Civil Engineering paper 1 2020 questions
- A cantilever beam is in the form of a quarter of a circle in vertical plane and is subjected to a vertical load P at its free end as shown in the figure below. Find the vertical and horizontal displacements at the free end, if flexural rigidity is same throughout the length of cantilever.
[Figure] Quarter circle of radius R, fixed at the bottom, vertical load P at the free top end
- Draw characteristic stress-strain curve for concrete, mild steel and HYSD steel in flexure giving all relevant values as per codal recommendations for limit state design of RCC structures.
- Two steel plates, each 100 mm wide and 10 mm thick are connected together by a lap joint using a single row of three bolts, along width, of property class 4.6. The diameter of each bolt is 16 mm and the ultimate tensile strength of steel plates is $410\,\mathrm{N/mm^2}$. Calculate the efficiency of the joint if the plates are in tension. Use limit state procedure.
Given : $f_{ub} = 400\,\mathrm{N/mm^2}$ for bolts of property class 4.6.
- A 1.5 cm wide gap between two vertical plane surfaces is filled with an oil of specific gravity 0.9 and dynamic viscosity $2.0\,\mathrm{Ns/m^2}$. A metal plate $1.0\,\mathrm{m}\times1.0\,\mathrm{m}\times0.1\,\mathrm{cm}$ thick and weighing 20 N is placed midway in the gap. Find the force required if the plate is to be lifted up with a constant velocity of 0.1 m/s.
- A pit is to be excavated in a fine sand stratum completely saturated up to the ground surface. The void ratio of the soil was 0.5 and specific gravity of soil solids is 2.7. The pit is to be dug to a depth of 6.3 m. To stabilise the bottom of the excavation (to prevent sand boiling) it is decided to drive steel sheet piles to act as cut-off walls that encircle the excavation. Determine the minimum depth of sheet piling required for an impending quick condition. Derive the formula, if any, used. Use unit weight of water as $9.81\,\mathrm{kN/m^3}$.
- Determine the force in members GE, GC and BC of the truss shown in the figure below. Indicate whether the members are in tension or compression.
[Figure] Truss with joints A, B, C, D (bottom chord) and G, E (top); spans 4 m, 4 m, 4 m; height 3 m; 400 N horizontal at E; 1200 N vertical at C; A pinned, D roller
- A reinforced concrete beam having a clear simply supported span of 6 m is required to support live and superimposed loads of 18 kN/m and 12 kN/m respectively. The materials to be used are M 25 grade concrete and Fe 250 grade steel. Design the section of the beam, and the main longitudinal reinforcement. The width of support is 500 mm. Use limit state design method.
- A hydraulic jump occurs in a triangular channel having sides sloping at $45^\circ$. Derive an equation relating two depths and the flow rate.
If the depths before and after the jump in the channel are 0.5 m and 1.0 m, find out the flow rate and Froude numbers before and after the jump.
- The in situ moisture content of a soil at a borrow area is 14% and its moist unit weight is $17.0\,\mathrm{kN/m^3}$. The specific gravity of the solids of the soil is 2.7. The soil is to be excavated and transported to a construction site for use in a compacted fill. The finished compacted volume is $2500\,\mathrm{m^3}$. If the specifications call for the soil to be compacted to a dry unit weight of $18.0\,\mathrm{kN/m^3}$ at the moisture content of 16%, determine the volume of soil to be borrowed from the borrow site. Also determine the degree of saturation of the soil after compaction and amount of water to be added to the borrow soil to achieve the desired compaction. Assume unit weight of water = $9.81\,\mathrm{kN/m^3}$.
- Design a full penetration butt weld to connect a 16 mm thick bracket plate perpendicular to the flange of a column. A factored load of 230 kN is applied to the bracket at a distance of 350 mm from the flange of the column. Field welds and steel of grade Fe 250 were used. Also give a neat sketch of the connection. Use limit state procedure.
- A Pelton wheel develops 15000 kW power under a head of 250 m. Find rotational speed of wheel, number of jets required, size of each jet, dimensions of buckets and number of buckets.
Given : $C_v = 0.98$, $K_u = 0.46$, $\eta_o = 0.88$, $\frac{D}{d} = 14$ and specific speed = 30.
- A small T-beam is used in an inverted position to span 400 mm. Find the value of P if due to the application of three forces shown in the figure, the longitudinal gauge at A registers a compressive strain of $50\times10^{-5}$. Also determine the maximum bending stresses in the beam.
Given : E = 200 GPa.
[Figure] Simply supported beam with loads P, P and 3P at spacings 100 mm, 100 mm, then section A-A 50 mm from the 3P load, 50 mm, then 100 mm to the support; Section A-A: T-section, flange 12 mm wide and 4 mm thick, web 4 mm wide, total height 12 mm shown, strain gauge A at 3 mm from the top
- A certain fluid is flowing through the pipe bend as shown in the figure below. Determine the forces exerted by the pipe boundary on the fluid, if given that $p_1 = 2.452$ bar (gauge), $v_1 = 4.0$ m/s, $D_1 = 0.3$ m, $D_2 = 0.15$ m, $\theta = 60^\circ$ and $\rho = 1000\,\mathrm{kg/m^3}$.
[Figure] Pipe bend (laid horizontal) with sections 1-1 and 2-2, turning angle $\theta = 60^\circ$
- Two footings are placed at a depth of 1.0 m on a sand layer as shown in the figure below. The footing at the left is of size $2\,\mathrm{m}\times2\,\mathrm{m}$ and that at the right $1.5\,\mathrm{m}\times1.5\,\mathrm{m}$ and carry loads of 400 kN and 225 kN, respectively. The location of water table and other relevant soil properties are shown in the figure. If the settlement of the footing is considered only because of the consolidation of compressible clay layer (ignoring elastic settlement of sand and clay), where do you expect the maximum settlement ? Justify your answer. Also determine the maximum consolidation settlement for the footing soil condition shown in the figure. Assume unit weight of water as $9.81\,\mathrm{kN/m^3}$. Assume 2.0 vertical 1.0 horizontal dispersion of footing pressure over depth.
[Figure] Footings 2 m x 2 m (400 kN) and 1.5 m x 1.5 m (225 kN), 2 m apart (centre-to-centre distance as drawn), founded 1 m below ground; sand layer with WT at 1 m below footing level, $\gamma = 18.0\,\mathrm{kN/m^3}$; compressible clay layer 3 m thick, $C_c = 0.4$, $e_o = 1.0$, $\gamma = 17.0\,\mathrm{kN/m^3}$; sand and gravel below
- Blocks A and B are connected through a cord and rest on the inclined planes as shown in the figure below. What is the tension in the cord, if the friction at block A reaches the maximum value ? Assume that pulley at C is frictionless. Block A weighs 300 N and Block B weighs 400 N.
[Figure] Block A (300 N) on a $60^\circ$ incline, block B (400 N) on a $30^\circ$ incline, joined over pulley C at the apex; $\mu = 0.2$ on both planes
- Determine the effective net area for the angle section shown in the figure, subjected to tensile force.
Bolts are of grade 4.6, and the steel is of grade Fe 410.
[Figure] ISA 125 x 95 x 10 mm connected to a 12 mm steel plate; 18 mm $\phi$ bolts staggered at 50 mm pitch (gauge distances 35 and 50); 20 mm $\phi$ bolts at 100 mm pitch; outstanding leg dimensions 55 and 40. All dimensions in mm
- An 8 m long beam is loaded with a uniformly distributed load, w/m over the entire span. The beam is supported at supports A and B as shown in Figure (a). Bending moment diagram for the beam is shown in Figure (b). Determine the value of udl, w and draw the shear force diagram. Also determine the maximum bending moment in the beam and its point of application.
[Figure] (a) beam with udl w/m, support A at left end, support B at 6 m, overhang of 2 m; (b) bending moment diagram, positive between supports and negative of 30 kN-m at B
- The drag of a sonar transducer is to be predicted, based on wind tunnel test. The prototype, a 0.3 m diameter sphere, is to be towed at 2.57 m/s in sea water at $4.5^\circ\mathrm{C}$. The model is 152 mm in diameter. Determine the required test speed in air. If the drag of the model at these test conditions is 2.7 N, estimate the drag of the prototype. Given that at $4.5^\circ\mathrm{C}$, $\rho_{\mathrm{sea\ water}} = 1000\,\mathrm{kg/m^3}$, $\upsilon_{\mathrm{sea\ water}} = 1.57\times10^{-6}\,\mathrm{m^2/s}$ and at STP, $\rho_{\mathrm{air}} = 1.227\,\mathrm{kg/m^3}$, $\upsilon_{\mathrm{air}} = 1.46\times10^{-5}\,\mathrm{m^2/s}$.
- An unsupported cut is made at a site as shown in the figure below. Determine :
(i) Lateral stress at the top and bottom of the cut.
(ii) The maximum depth of potential tension crack.
(iii) The maximum depth of unsupported cut possible at the site.
(iv) If the soil is excavated upto 8 m depth and supported by a vertical earth retaining wall, total active thrust on the wall.
[Figure] Vertical cut 4 m deep; soil $\gamma = 18.0\,\mathrm{kN/m^3}$, $c = 25\,\mathrm{kN/m^2}$, $\phi = 10^\circ$
- Find expression for boundary layer thickness ($\delta$), shear stress ($\tau_0$) and average coefficient of drag ($\bar{c}_f$) in terms of Reynolds number, if velocity profile of laminar boundary layer is given as :
$\frac{u}{U} = \frac{y}{\delta}$
- Using displacement method, analyse the frame given in the figure below, if flexural rigidity is constant throughout.
[Figure] Portal frame A-B-C-D: columns AB (height 6 m, fixed at A) and CD (fixed at D), beam BC 6 m with udl 40 kN/m, overhang CE 4.5 m with roller support at E
- The floor slab of a room has clear dimensions of $4.0\,\mathrm{m}\times9.0\,\mathrm{m}$ and the slab is simply supported on 230 mm thick masonry walls. The floor loading consists of a live load of $6\,\mathrm{kN/m^2}$ and dead load due to finishing work is $1.5\,\mathrm{kN/m^2}$. Steel of grade Fe 415 and concrete of grade M 25 is used for construction. Design the floor slab and check it for deflection. Use limit state design method.
[Figure] Modification Factor for Tension Reinforcement: curves for $f_s$ = 120, 145, 190, 240, 290 against percentage tension reinforcement (0.4 to 3.0); modification factor axis 0 to 2.0. Note : $f_s$ is Steel Stress of Service Loads in $\mathrm{N/mm^2}$; $f_s = 0.58 f_y \times \frac{\text{Area of cross-section of steel required}}{\text{Area of cross-section of steel provided}}$
- A cohesionless soil specimen in a triaxial test is subjected to a major and minor principal stress $\sigma_1$ and $\sigma_3$ respectively. Draw Mohr's circle and derive an expression for $\phi$ in terms of $\sigma_1$ and $\sigma_3$. Also derive the expressions for shear stress, $\tau$ and normal stress, $\sigma$ on the failure plane in terms of $\sigma_1$, $\sigma_3$ and $\phi$.
- A square footing $0.3\,\mathrm{m}\times0.3\,\mathrm{m}$ is placed on the surface of dense cohesionless sand with unit weight $18.0\,\mathrm{kN/m^3}$ and subjected to a load test. If the footing fails at a load of 47.5 kN, what is the value of $\phi$ for the sand ? The table given below may be used.
If a footing of size $1.5\,\mathrm{m}\times1.5\,\mathrm{m}$ is proposed on the same soil with a depth of foundation 1.0 m, what will be the allowable capacity of the footing with a factor of safety of 2.5 ? In all cases water table was at a great depth and its effect is to be ignored.
| $\phi^\circ$ | $N_c$ | $N_q$ | $N_\gamma$ |
| --- | --- | --- | --- |
| 18 | 13.10 | 5.26 | 2.00 |
| 20 | 14.83 | 6.40 | 2.87 |
| 22 | 16.88 | 7.82 | 4.07 |
| 24 | 19.32 | 9.60 | 5.72 |
| 26 | 22.25 | 11.85 | 8.00 |
| 28 | 25.80 | 14.72 | 11.19 |
| 30 | 30.14 | 18.40 | 15.67 |
| 32 | 35.49 | 23.18 | 22.02 |
| 34 | 42.16 | 29.44 | 31.15 |
| 36 | 50.59 | 37.75 | 44.43 |
| 38 | 61.35 | 48.93 | 64.08 |
| 40 | 75.32 | 64.20 | 93.69 |
- A welded plate girder 22 m in span is laterally restrained throughout, and carries a uniformly distributed load of 100 kN/m excluding the self weight. The girder is without intermediate transverse stiffeners. The steel used is of grade Fe 410. Design the cross-section and the welded connections. Draw a neat sketch of the designed section. Use limit state design method. The plate girder is fabricated in the workshop.
- Explain the conditions when vane shear test is suitable for determining the shear strength of the soil. Derive an expression for shear strength of soil in terms of applied torque and vane dimensions considering shearing at top, bottom and surrounding soil.
An in situ vane shear test was conducted in a clay soil at the bottom of a borehole. A torque of 150 N-m was required to shear the soil. What was the undrained shear strength of clay neglecting shearing resistance at the top ? The vane was 100 mm in diameter and 150 mm long.
- An oil of viscosity 18 poise flows between two horizontal fixed parallel plates which are kept at a distance 150 mm apart. The maximum velocity of flow is 1.5 m/s. Find :
(i) Pressure gradient
(ii) Shear stress at two horizontal parallel plates
(iii) Discharge per unit width for laminar flow of oil
- Analyse the propped cantilever as shown in the figure below and determine the collapse load.
[Figure] Beam AB of length L, fixed at A and propped at B, with udl $w = \frac{W}{L}$