Mains PYQs
UPSC Mains Civil Engineering paper 1 2019 questions
- A particle moves from the origin, in the x-y plane so that at any time 't' its acceleration along the 'x' and 'y' axes are $a_x = -6\,\mathrm{m/sec^2}$ and $a_y = 6\,\mathrm{m/sec^2}$. At t = 0, its velocity is 3 m/sec entirely along the x-axis. Find the equation to the path of the particle. Also find the minimum velocity of the particle.
- A reinforced concrete beam of rectangular section 300 mm $\times$ 500 mm is reinforced in tensile zone by 4 bars of 16 mm diameter having an effective cover of 40 mm. The beam is loaded with a factored load including its self-weight as shown in the figure below.
[Figure] 30 kN/m uniformly distributed load on a beam with a 10 m span between supports and a 4 m overhang
Design the vertical shear reinforcement for the beam at critical section for shear. Take M 25 grade of concrete and Fe 415 grade of steel.
Use the following data :
For M 25 concrete, $\tau_{c,max} = 3.1\,\mathrm{N/mm^2}$
| $\frac{100 A_s}{bd}$ | 0.25 | 0.5 | 0.75 | 1.00 |
|---|---|---|---|---|
| $\tau_c$ (N/mm$^2$) | 0.36 | 0.49 | 0.57 | 0.70 |
- Design a bearing plate at the support for ISMB 600 @ 1202.71 N/m resting on a brick masonry wall 230 mm thick for the support reaction of 180 kN. Assume the permissible bearing stress for brick wall be 4.0 N/mm$^2$ and partial safety factor $\gamma_{mo}$ = 1.1. The sectional properties of ISMB 600 are as follows :
Grade of steel $f_y$ = 250 MPa
Width of flange $b_f$ = 210 mm
Thickness of flange $t_f$ = 20.8 mm
Thickness of web $t_w$ = 12 mm
Radius of root R = 20 mm
- In a flow field, the following velocity components are given :
$u = 2xy$ and $v = a^2 + x^2 - y^2$
Show that the flow is possible. Obtain the relevant stream function.
- A 1.0 m$^3$ moist soil sample weighs 20.0 kN. The water content of the soil is 10%. The specific gravity of solids, $G_s$ can be assumed as 2.7. With this information, fill in all blanks in the phase diagram. Also determine the void ratio and degree of saturation of the soil sample. Assume unit weight of water, $\gamma_w$ = 9.81 kN/m$^3$.
[Figure] Phase diagram with Air, Water and Solid blocks: $V_a$ = __, $V_w$ = __, $V_s$ = __, $V_v$ = __, $V_t$ = __, $W_w$ = __, $W_s$ = __, $W_t$ = __
$V_t$ = total volume, $V_v$ = volume of void, $V_a$ = volume of air, $V_w$ = volume of water, $V_s$ = volume of solids, $W_t$ = total weight, $W_w$ = weight of water, $W_s$ = weight of solids.
- The cross-section of a prestressed concrete beam of span 12 m is as shown in the figure. The beam has to carry a superimposed load of 20 kN/m. The prestressing force is transmitted by tendons having 605 mm$^2$ area, subjected to an initial prestress of 1100 N/mm$^2$. Analyse the beam section at centre for the stresses induced before and after the application of superimposed load. Allow 15% loss of prestress. Assume location of N.A. as 393.5 mm from bottom edge and $I_{xx}$ about N.A. is $13900 \times 10^6\,\mathrm{mm^4}$.
[Figure] I-section: top flange 250 wide, 100 deep; web 100 wide, 500 high above N.A.; N.A. 393.5 from bottom edge; bottom flange 200 wide, 200 deep; $A_{st}$ = 605 mm$^2$ placed 100 from bottom. All dimensions are in mm
- The pressure drop $\Delta P$ generated by a pump depends on impeller diameter D, the rotational speed N, the fluid discharge Q, the fluid density $\rho$ and viscosity $\mu$. Using Buckingham $\pi$-theorem, obtain dimensionless form of the functional relationship.
- A tapering chimney of hollow circular section is 40 m high. Its external diameter at the base is 3.0 m and at the top it is 2.0 m. It is subjected to wind pressure of 2.0 kN/m$^2$ of the projected area. If the weight of the chimney is 5000 kN and internal diameter at the base is 1.2 m, determine the maximum and minimum stress intensities at the base.
- A three-hinged parabolic arch has a span of 40 m and a central rise of 8 m. Five wheel loads of 5, 6, 6, 4, 4 kN spaced 4 m, 3 m, 4 m and 3 m in order, cross the arch from left to right with the 5 kN load leading. When the leading load is 30 m from the left hinge, calculate the horizontal thrust in the arch. Also calculate the bending moment and normal thrust at the section under the tail load.
- A built-up steel section is as shown in the figure. Determine the axial load capacity in compression for the data given below :
$f_y$ = 250 MPa, L = 5.0 m, $t_w = t_f$ = 30 mm, $\gamma_{mf}$ = 1.5
The connection between web and flanges are welded connection. Both the column ends are restrained in direction and position. The buckling curve to be used along zz-axis is 'b' and that along yy-axis is 'c'.
[Figure] Built-up I-section: flanges 300 mm wide and 30 mm thick, web 30 mm thick, 400 mm clear between flanges, zz horizontal axis, yy vertical axis
The design compressive stresses for slenderness ratio for curve 'b' and 'c' are given below.
| Slenderness Ratio $\frac{KL}{r}$ | | 40 | 50 | 60 | 70 | 80 | 90 |
|---|---|---|---|---|---|---|---|
| Design compressive stress, $f_{cd}$ in N/mm$^2$ | for curve 'b' | 206 | 194 | 181 | 166 | 150 | 134 |
| | for curve 'c' | 198 | 183 | 168 | 152 | 136 | 121 |
- At a given site, the soil stratum consists of a thick clay layer. The ground water table is located 2.0 m below the ground surface. Above the ground water table, the degree of saturation of the soil is 90%. If the specific gravity of solids of soil is equal to 2.7 and the void ratio of the soil is 1.0, determine
(i) at which depth below the ground surface the vertical effective stress is equal to 100 kPa.
(ii) what is the vertical effective stress at the same depth, immediately after the ground water table is lowered further by 2.0 m. Assume unit weight of water, $\gamma_w$ = 9.81 kN/m$^3$.
- A rectangular R.C. water tank with an open top is required to store 100 m$^3$ of water. The inside dimensions of tank may be taken as 6 m $\times$ 5 m. The tank rests on the ground. Design the side walls of the tank using approximate design method. The free board is 150 mm. Use M 20 concrete and Grade-I steel. The permissible stresses are
$\sigma_{cbc}$ = 7.0 N/mm$^2$
$\sigma_{st}$ = 100 N/mm$^2$ (near water face)
$\sigma_{st}$ = 125 N/mm$^2$ (away from water face)
Assume distribution factor as 0.5 at junction for both walls.
- A strip footing of width 2.5 m is to be constructed on a thick deposit of uniform cohesionless soil. The saturated and dry unit weight of soil are 20.0 kN/m$^3$ and 18.0 kN/m$^3$, respectively. The angle of internal friction of the soil is 35$^\circ$ and the depth of the footing, $D_f$ is 1.5 m. Also for $\phi$ = 35$^\circ$ given $N_c$ = 57.8, $N_q$ = 41.4 and $N_r$ = 42.4.
(i) Assuming the water table at a great depth for which the effect of water table on the bearing capacity can be neglected, determine the allowable bearing capacity of the footing as per Terzaghi's bearing capacity theory with a factor of safety of 3.0.
(ii) Determine the allowable bearing capacity for the same footing with same F.S., when the water table rises to the base of the footing.
(iii) Also determine the allowable bearing capacity of the same footing with same F.S., if it is placed on the ground surface and water table is also on the ground surface. Assume unit weight of water, $\gamma_w$ = 9.81 kN/m$^3$.
- A rectangular weir of crest width 0.4 m is used to measure the discharge in a rectangular channel 0.6 m wide and 0.45 m deep.
If the water level in the channel is 0.225 m above the crest, find the discharge in the channel. Velocity of approach to be considered. Assume $C_d$ = 0.63.
- The coefficient of static and kinetic friction between the 200 kg block and inclined plane shown in the figure below are 0.3 and 0.2 respectively. Determine
(i) the friction force 'F' acting on the block when 'P' is applied with a magnitude of 400 N to the block at rest.
(ii) the force 'P' required to initiate motion up the incline from rest.
(iii) the friction force 'F' acting on the block if P = 1600 N.
[Figure] Block on a 20$^\circ$ inclined plane with force P applied at 30$^\circ$ to the incline
- A column has an unsupported length of 3.4 m and is effectively held in position at its both ends, but not restrained against rotation. The cross-section of the column and reinforcement details are shown in the figure below. Determine the safe axial load that the column can carry. Use M 25 grade of concrete and Fe 415 grade of steel.
[Figure] Circular column section, 400 mm diameter, 6 bars of 16 $\phi$, 6 $\phi$ spiral @ 45 mm c/c pitch, 40 mm clear cover
- The velocity profile over a horizontal flat plate held in a free stream with a velocity U is given by
$U = A \sin (By) + C$
Evaluate the constants A, B and C.
- The compression curve for a certain clay soil is a straight line on the semi-logarithmic plot and it passes through the points $e$ = 1.15, $\sigma_v'$ = 65 kPa and $e$ = 0.76, $\sigma_v'$ = 825 kPa.
Write the generalised equation of change in void ratio, $\Delta e$ for the soil. Also determine the change in void when the pressure on the soil increased from 100 kPa to 400 kPa.
- A dry sand specimen (cohesion = 0) is put through a drained triaxial test. For a cell pressure of 100 kPa, the sample failed at a deviator stress of 350 kPa. Determine the angle of internal friction, $\phi$ of the sand specimen from the given test data. Also determine the deviator stress at failure for the same soil sample when cell pressure applied is 200 kPa.
- Using conjugate beam method, for the beam shown below, find the slopes and deflections at 'A', 'B', 'C' and 'D'. Given : $E = 200 \times 10^6\,\mathrm{kN/m^2}$ and $I = 300 \times 10^{-4}\,\mathrm{m^4}$. Neglect the weight of the beam.
[Figure] Beam AB with three 10 m segments of moment of inertia I, 3I and 2I; loads 75 kN at C and 150 kN at D
- A steel beam section ISMB 400 @ 604.30 N/m is supported on RCC column and has bearing length 150 mm. Calculate the load bearing capacity of this steel beam under web buckling at support. Assume the grade of steel Fe 410 and permissible stresses ($f_{cd}$) according to buckling curve 'C' are as given below. The cross-sectional properties of ISMB 400 are as
Sectional Area A = 78.40 cm$^2$
Width of Flange $b_f$ = 140 mm
Thickness of Flange $t_f$ = 16 mm
Thickness of Web $t_w$ = 8.9 mm
$R_1$ = 14.0 mm
Permissible (Design Compressive) stress ($f_{cd}$) as per buckling curve 'C'
| $\frac{KL}{r}$ | 70 | 80 | 90 | 100 | 110 |
|---|---|---|---|---|---|
| $f_{cd}$ (N/mm$^2$) | 152 | 136 | 121 | 107 | 94.6 |
- A 15 m long and 10 m wide raft is placed on a 16 m thick clay deposit, consisting of 4 sub-layers as shown in the figure below. Determine the settlement of the raft foundation because of the consolidation of the clay layers. Assume unit weight of water, $\gamma_w$ = 9.81 kN/m$^3$.
[Figure] Raft with 100 kPa load at 2 m depth; WT at the raft base level; 2 m above; four 4 m layers: $e_0$ = 0.9, $c_c$ = 0.15, r = 17.0 kN/m$^3$; $e_0$ = 0.85, $c_c$ = 0.14, r = 17.5 kN/m$^3$; $e_0$ = 0.75, $c_c$ = 0.12, r = 18.0 kN/m$^3$; $e_0$ = 0.70, $c_c$ = 0.10, r = 18.5 kN/m$^3$; r above the water table = 17.0 kN/m$^3$
- A discharge of 16 m$^3$/sec flows with a depth of 2.0 m in rectangular channel of width 4.0 m. At a downstream section, the width of channel is reduced to 3.5 m, and the channel bed is raised by 0.20 m. Analyse the water surface elevation in the transition.
- Design a floor slab for an interior roof slab with clear dimensions of 8.5 m $\times$ 3.5 m for a building located in Delhi. The slab is resting on 230 mm thick masonry walls. The superimposed load may be taken as 5 kN/m$^2$. Use M 25 grade of concrete and Fe 415 grade of steel.
The following data may be used :
| Exposure | Moderate | Severe | Very Severe |
|---|---|---|---|
| Nominal concrete cover (in mm), not less than | 30 | 45 | 50 |
| Basic values of span to effective depth ratios for spans up to 10 m | Cantilever | Simply Supported | Continuous |
|---|---|---|---|
| | 7 | 20 | 26 |
[Figure] Modification Factor for Tension Reinforcement: modification factor (0 to 2.0) against percentage tension reinforcement (0 to 3.0), curves for $f_s$ = 120, 145, 190, 240, 290. Note : $f_s$ is steel stress of service loads in N/mm$^2$. $f_s = 0.58 f_y \frac{\text{Area of cross-section of steel required}}{\text{Area of cross-section of steel provided}}$
- Calculate the flexural stiffness at point 'D' of the three span continuous beam ABCD shown in the figure below.
[Figure] Continuous beam ABCD with supports at B, C and D, A free end; spans AB = 10 m (2I), BC = 10 m (I), CD = 10 m (2I)
- The earth retaining wall shown in the figure is to support a backfill of granular soil, which has unit weight of 17.0 kN/m$^3$ and angle of internal friction of 40$^\circ$. The wall also supports a surcharge of 25.0 kN/m$^2$ as shown in the figure. The coefficient of base friction is 0.5. Determine the factor of safety against sliding and overturning for the wall. Also determine the maximum and minimum vertical pressure below the base of the retaining wall.
[Figure] Retaining wall 6.0 m high, top width 1.2 m, base width 3.3 m, $r_c$ = 24.0 kN/m$^3$; backfill r = 17.0 kN/m$^3$, $\phi$ = 40$^\circ$; surcharge 25.0 kN/m$^2$
- Find the collapse load for the portal frame loaded as shown in the figure below.
[Figure] Portal frame, width 2l, height 2l, fixed bases; horizontal load F at beam level, vertical load 4F at beam mid-span; plastic moment $M_p$ in columns and $2M_p$ in beam
- A vertical shaft Kaplan turbine operating under a head of 9.8 m has a runner diameter of 9.3 m. The turbine runs at 51.7 rpm and develops 45000 kW power by discharging 535 m$^3$/sec of water. Determine the values of unit speed, unit discharge, unit power and specific speed of the turbine.
If the critical value of cavitation coefficient for runner is 0.95, determine the location of the runner with respect to the tail water level. Assume atmospheric pressure head as 9.8 m and saturation vapour pressure head as 2.5 m.