Mains PYQs
UPSC Mains Civil Engineering paper 1 2018 questions
- Draw the free body diagram for lower and upper parts of the system. Calculate all reactions for the figure shown below.
[Figure] Beam ABC with fixed support at A and roller support at B, hinge at C joined to upper beam CDE fixed at E; 5 kN load at D; spans 0.3 m, 0.5 m, 0.3 m, 0.5 m.
- 16 mm plates are joined together by single riveted lap joint in one of the following ways. Calculate which of the two ways will give a stronger joint :
(i) 24 mm rivets at 60 mm pitch
(ii) 30 mm rivets at 90 mm pitch
Given : $p_t = 150$ MPa, $p_s = 102.5$ MPa, $p_b = 236$ MPa
- Calculate the ultimate flexural strength of a T-beam section having the following sectional properties :
Width of the flange = 1200 mm
Depth of the flange = 120 mm
Width of the rib = 300 mm
Effective depth = 600 mm
Area of tensile steel = 8 bars of 25 mm diameter
Materials : M 20 grade concrete and Fe 415 HYSD bars
- The velocity distribution for the flow of a Newtonian fluid between two fixed wide, parallel plates is given by the following equation :
$$u = \frac{3V}{2}\left[1 - \left(\frac{y}{h}\right)^2\right]$$
where V is the mean velocity.
If the fluid viscosity is $2\,\mathrm{Ns/m^2}$, $V = 0.6\,\mathrm{m/s}$ and $h = 5$ mm, determine
(i) the shearing stress acting on the bottom wall, and
(ii) the shearing stress acting on a plane parallel to the wall and passing through the centre line (mid-plane).
[Figure] Parabolic velocity profile u between two parallel plates, distance h on each side of the centre line, y measured from the centre line, x along the flow.
- During a compaction work, a 1 m thick stratum of soil was compacted to a total of 30 mm via a roller. Initially the void ratio of soil was 0.9, and the water content was 15%. Determine the final void ratio of the compacted stratum. Also determine the dry unit weight of the soil before and after the construction and initial and final degree of saturation of the soil. Assume the specific gravity of the soil particles, $G = 2.7$ and unit weight of water, $\gamma_w = 9.81\,\mathrm{kN/m^3}$.
- Calculate maximum force in the diagonal member $U_2L_2$ of the truss shown in the figure below, for a moving load of 20 kN/m (intensity) and 50.0 m in length. It is proposed that this moving load will be transmitted through the bottom chord. (Neglect the self-weight of truss)
[Figure] Pratt-type truss with top joints $U_1$ to $U_5$ and bottom joints $L_0$ to $L_5$, five panels of 10.0 m each (total 50.0 m), 60 degree angles at $L_0$ and $U_1$; hinge support at $L_0$, roller at $L_5$; moving load 20 kN/m over 50.0 m.
- Design a circular column of diameter 400 mm with helical reinforcement subjected to a working load of 1200 kN. Use M 20 concrete and Fe 415 steel. The column has unsupported length of 3 m and is effectively held in position at both ends, but not restrained against rotation.
- An inclined tube reservoir manometer is constructed as shown. Derive a general expression for the liquid deflection, L, in the inclined tube, due to the applied pressure difference, $\Delta p$.
[Figure] Reservoir of diameter D with gauge liquid of density $\rho_l$, level change $h_1$ at section 1; inclined tube of diameter d at angle $\theta$, liquid deflection L along the tube, level change $h_2$ at section 2; equilibrium liquid level marked; pressure difference $\Delta p$ applied at the reservoir.
- At a given site, an 8 m thick saturated clay is underlain by a sand layer. The natural water content of the clay soil was 30% and the specific gravity of soil particles was 2.7. The sand layer is under artesian pressure equivalent to 3 m of water head. It is proposed to make an excavation in the clay layer. How deep can the excavation be made before the bursting of the clay layer by bottom heave ? If a factor of safety of 1.5 is desired, what would be the depth of excavation for the same clay layer ? Assume unit weight of water, $\gamma_w = 9.81\,\mathrm{kN/m^3}$.
- A three-hinge parabolic arch, $y = \frac{2x}{3} - \frac{x^2}{45}$ has a span of 30.0 m and maximum rise of 5.0 m at centre. Arch is having uniform cross-section throughout. It is subjected to uniformly distributed load of 10 kN/m (dead load + live load).
Prove that Bending moment will be zero at all sections of arch.
[Figure] Three-hinge parabolic arch with hinge supports A and C and crown hinge B, span 30.0 m, rise 5.0 m, curve $y = \left(\frac{2x}{3} - \frac{x^2}{45}\right)$, UDL 10 kN/m over the span.
- Check the adequacy of the hanger connection shown in the figure below. The end plate welded connection shown in the figure need not be designed. The end distance of the bolt is 35 mm. Two bolts of 30 mm diameter are used to make the connection. The end plate is 230 mm $\times$ 150 mm in size. For 30 mm bolt, $A_{nb} = 561\,\mathrm{mm^2}$, $d_h$ and $d_0$ = 33 mm, $f_{ub}$ = 400 MPa.
[Figure] Hanger connection: end plate 230 mm wide, 25 mm thick, with two bolts, end distance 35 mm, 16 mm thick hanger plate attached by 8 mm fillet weld, carrying 200 kN.
- The drag force F, on a smooth sphere depends on the relative speed V, the sphere diameter D, the fluid density $\rho$ and the fluid viscosity $\mu$. Using Buckingham $\pi$-theorem, obtain a set of dimensionless groups that can be used to correlate experimental data. Select the repeating parameters as $\rho$, V, D.
- A square footing rests on a uniform thick deposit of stiff clay with an unconfined compressive strength of 120 kPa. The footing is located at 1.2 m below the ground surface and is to carry a total load of 1000 kN. The unit weight of clay soil is $20\,\mathrm{kN/m^3}$ and ground water level is at a great depth and its effect can be ignored. Determine the dimension of square footing required for the loading and soil conditions given with a factor of safety of 3. What would be the diameter of the footing if a circular footing is used instead of square footing at the same depth ?
- Bending moment diagram for a beam carrying uniformly distributed load has been shown below. Bending moment diagram curve is parabolic and follows the equation $y = \frac{ax^2}{2}$ in AB and DE portion.
Calculate the values of load and plot loading and shear force diagram.
[Figure] Bending moment diagram over points A, B, C, D, E: AB = 2.0 m and DE = 2.0 m with negative parabolic curve $y = \frac{ax^2}{2}$, BD = 6.0 m, moment 20 kN-m (negative) at B and at D, positive peak 25 kN-m at C, with 3.0 m dimension marked at the centre.
- A cantilever beam carries a uniformly distributed load over its entire length. Maximum possible deflection at the free end 'B' is limited to 40 mm. Calculate the magnitude of maximum possible uniformly distributed load (dead load + live load) for a combined factor of safety of 1.5 on this beam.
$E = 200 \times 10^6\,\mathrm{kN/m^2}$
Size of beam = 200 mm $\times$ 400 mm
[Figure] Cantilever AB fixed at A, length 5.0 m, with UDL; cross-section 200 mm wide and 400 mm deep.
- Channel section shown in the figure is carrying water to full depth. Permissible stress in channel material is limited to 200 MPa. Channel will be simply supported at its ends. Calculate this support spacing for a factor of safety 1.5 to the loads. Neglect self-weight of channel. Unit weight of water is $10\,\mathrm{kN/m^3}$.
[Figure] U-shaped channel section: overall width 1020 mm, overall height 1010 mm, wall thickness 10 mm on each side and 10 mm at the bottom, water level at top.
- A prestressed concrete beam of span 10 m is prestressed by a parabolic cable of cross-sectional area $200\,\mathrm{mm^2}$. The eccentricity of cable at support sections is 50 mm above and at mid-span section 50 mm below the neutral axis.
Given : Cross-section of beam = 100 mm $\times$ 300 mm, $\mu = 0.35$, $K = 0.15/100$ m. If the cable is jacked from one end only, calculate friction loss.
- A turbine develops 107 kW running at 100 rev/min under a head of 7.6 m.
(i) What power would be developed under a head of 11 m assuming the same flow ?
(ii) At what speed should the turbine run ?
- A rigid retaining wall of height 6 m retains a dry cohesionless levelled backfill with angle of internal friction, $\phi = 30^\circ$ and unit weight, $\gamma_s = 18\,\mathrm{kN/m^3}$. A support is to be provided behind the wall to prevent from yielding of wall. Determine the force on the support if used to prevent yielding of wall for a unit length of wall. Also, determine the point of application of the support from the base of the wall.
- A straight stair in a residential building is supported on a wall at one side and by a stinger beam on the other side, with a horizontal span of 1.2 m. The risers are 150 mm and treads 300 mm. Design the steps. Use M 20 concrete and Fe 415 steel. Take live load as $3\,\mathrm{kN/m^2}$.
- A cylindrical chimney 1 m in diameter and 25 m tall is exposed to a uniform 50 km/h wind at standard atmospheric conditions. End effects and gusts may be neglected. Estimate the bending moment at the base of the chimney.
Given :
$P$ = 101 kPa (abs)
$C_D$ = 0.35
$\rho = 1.23\,\mathrm{kg/m^3}$
$\mu = 1.79 \times 10^{-5}\,\mathrm{kg/ms}$
[Figure] Vertical chimney of diameter d = 1 m and height L = 25 m, drag force $F_D$ acting at L/2.
- A sample of dry cohesionless soil is subjected to a triaxial test. From another test on a sample of same soil, the angle of internal friction of the soil was estimated as $40^\circ$. If the minor principal stress of 100 kPa is applied on the sample during the test, at what values of deviator stress ($\Delta p$) and major principal stress will the test specimen fail ?
- Calculate the value of Plastic Moment '$M_p$' for the beam shown below.
[Figure] Beam A to F fixed at A, point loads 100 kN at B, 100 kN at C and 200 kN at E acting downward, supports (upward arrows) at D and F; spacings 1.0 m, 2.0 m, 1.0 m, 2.0 m, 1.0 m; total 7.0 m.
- Explain the principles of working stress method and limit state method of design of R.C. members.
- A laboratory wind tunnel has a test section that is 305 mm square. Boundary-layer velocity profiles are measured at two cross-sections and displacement thicknesses are evaluated from the measured profiles. At section (1), where the free stream speed is $u_1 = 26$ m/s, the displacement thickness is $\delta_1^* = 1.5$ mm. At section (2), located downstream from section (1), $\delta_2^* = 2.1$ mm. Calculate the change in static pressure between section (1) and section (2). Express the result as a fraction of the free stream dynamic pressure at section (1). Assume standard atmospheric conditions.
- A square pile group consists of four friction piles, constructed on a cohesive soil deposit. Diameter of each pile was 300 mm, length was 10 m and centre-to-centre spacing between the piles was 750 mm. Unconfined compressive strength of the cohesive soil was determined as 200 kPa. Assuming adhesion factor = 0.6, determine :
(i) Group capacity of the piles based on block failure criterion with a factor of safety of 3.
(ii) Group capacity based on the individual pile failure criterion. Assume factor of safety for single pile = 2 and estimating group efficiency by the Converse-Labarre equation or any other method.
(iii) Design capacity of the pile.
- A rectangular channel 12.2 m wide carries $25.47\,\mathrm{m^3/s}$ of water. The slope of the channel is 0.00283. At section (1) the depth is 1.37 m and at section (2), 92 m downstream, the depth is 1.52 m. What is the average value of Manning's roughness factor 'n' ? Take $g = 9.81\,\mathrm{m/s^2}$.
- A square footing of size 3 m $\times$ 3 m is placed on a sand and gravel layer at a depth of 1.5 m from the ground surface. Below the sand and gravel layer, a layer of normally consolidated soil of thickness 3 m is present. Details of soil properties and the footing loading are shown in the figure. Determine the total expected consolidation settlement for the clay layer because of the footing loading.
[Figure] Footing 3 m wide at 1.5 m depth carrying Q = 1100 kN; soil above footing level $\gamma = 18.5\,\mathrm{kN/m^3}$; water table (WT) at footing level; sand and gravel 4.5 m thick, $\gamma = 20.5\,\mathrm{kN/m^3}$; normally consolidated clay 3.0 m thick, $\gamma = 17.0\,\mathrm{kN/m^3}$, $e_0 = 1.2$, $C_c = 0.6$.