Mains PYQs
UPSC Mains Civil Engineering paper 2 2016 questions
- Write the full form and very briefly explain the underlined terms in the following sentences (Not more than 20 words should be written for each term) :
(i) The DPR for the project had to be revised. [2] [20 words]
(ii) The contractor should provide appropriate PPE to the workers at site. [2] [20 words]
(iii) Building bye-laws may permit a different FAR depending on the use of a building. [2] [20 words]
(iv) The project is being executed under the PPP scheme. [2] [20 words]
(v) An adjustment for TDS had to be made in the final bill paid. [2] [20 words]
- Indian codes give specifications for a minimum IST and a maximum FST for cements. Why? (Not exceeding 100 words)
- (i) Differentiate between systematic errors and accidental errors in survey work. [5]
(ii) A line $AB$ measures 10 cm on a photograph taken with a camera having a focal length of 22 cm. The same line measures 4 cm on a map drawn to a scale of $1/40000$. Calculate the flying height of the aircraft, if the average altitude is 400 m. [5]
- (i) Briefly explain the relevance of coning of wheels of a railway vehicle. [5]
(ii) Differentiate between wooden and concrete sleepers. [5]
- Explain with sketches the various factors controlling the highway alignment. What are their impacts on requirements of an ideal alignment?
- From workability and strength considerations, it is found that a concrete should have a unit water content and water-cement ratio of $180\,\mathrm{kg/m^3}$ and 0.50, respectively. Also, from a durability point of view, the maximum water-cement ratio allowed is 0.45.
Now, assuming that the mortar content of the mix should be 60% (by volume), determine the content of cement, sand and coarse aggregate in $\mathrm{kg/m^3}$ of concrete. Take specific gravity of cement, sand and coarse aggregate to be 3.14, 2.65 and 2.71, respectively, and ignore air content.
- Answer the following questions briefly :
(i) What tests are carried out to determine the mechanical properties of coarse aggregates used in concrete? (Not exceeding 50 words) [5] [50 words]
(ii) What is the purpose of the 'frog' provided in a brick used in masonry construction? (Not exceeding 50 words) [5] [50 words]
(iii) An equipment purchased for ₹ 5,00,000 has a useful life of 3 years and a salvage value of ₹ 50,000. Compare the book value of the equipment at the end of 2 years, determined using 'linear' depreciation and 'sum of digits' depreciation. [5]
- A steel tape 20 m long of standard length at $90\,^\circ\mathrm{F}$ was used for measuring a line, the mean temperature during measurement being $60\,^\circ\mathrm{F}$. The measured distance was 1550 m, the following being the slopes :
$1^\circ 50'$ for 100 m
$2^\circ 30'$ for 200 m
$3^\circ 10'$ for 300 m
$4^\circ 00'$ for 200 m
$5^\circ 30'$ for 400 m
$6^\circ 20'$ for 350 m
Compute the true length of the line, if the coefficient of expansion is $60 \times 10^{-7}$ per $1\,^\circ\mathrm{F}$.
- (i) What are the merits of CMS crossings over cast steel crossings? [5]
(ii) What would be the equilibrium cant on a curved BG track with a $2^\circ$ curve for an average speed of 70 kmph? Calculate the minimum permissible speed after allowing a maximum cant deficiency of 2.0 cm. [10]
- Consider the network for a construction project given below with the durations of activities $A$ through $F$ given in weeks :
[Figure] Network from a start node to an end node through three intermediate nodes: A (6 weeks) and B (4 weeks) through the top node, C (5 weeks) and D (3 weeks) through the middle node, E (7 weeks) and F (4 weeks) through the bottom node.
(i) What is the minimum time required for completion of the project? [3]
(ii) What is the earliest time ($T_E$) that activity $D$ can be started? [3]
(iii) What is the latest time ($T_L$) that activity $D$ must be started to ensure that the project is not delayed? [3]
(iv) Do questions (ii) and (iii) need the information obtained in question (i) above? [1]
- Define fibre reinforced concrete. Briefly explain how the presence of fibres in the matrix affects the properties of concrete.
- The following staff readings are observed successively with a levelling instrument. The levelling instrument has been moved after third, seventh and ninth readings :
1.568, 1.964, 0.898, 2.124, 2.986, 1.148,
0.746, 2.118, 1.444, 2.648, 2.248, 1.876
Calculate the RL of points, if the first reading is taken with a staff held on a BM of 842.248 m.
- (i) Analyze relative damage caused by axle loads of 4080 kg and 16320 kg to the flexible pavement. [5]
(ii) A four-lane divided NH need to be constructed for the following traffic volumes observed in 2014 :
| Vehicle type | Volume (vehicles/day) | Annual growth rate | VDF |
| --- | --- | --- | --- |
| Light CV | 4500 | 8% | 0.5 |
| Medium CV | 3000 | 6% | 1.5 |
| Heavy CV | 1500 | 4% | 3.5 |
Construction period : 2 years
Design life : 20 years
Determine the design traffic in terms of cumulative standard axles (CSA). [10]
- Discuss briefly the provisions in IS 456-2000 to ensure durability of reinforced concrete structures.
- Write brief answers to the following questions (not exceeding 50 words in each case) :
(i) What is 'escalation' in the context of construction contracts? [5] [50 words]
(ii) What is EPF in the context of welfare measures for construction workers? [5] [50 words]
(iii) In what kind of construction is a 'tremie' used? [5] [50 words]
- A NH, passing through a plain terrain with light rainfall intensity, has to be constructed with bituminous concrete surface. What should be the minimum radius of horizontal curve, when normal camber section is permitted?
- (i) Briefly explain the role of 'desire line diagram' in highway network planning. [5]
(ii) Design details of a rotary intersection are given below :
Design speed = 40 kmph
Width of weaving section = 9.0 m
Average width of entry and non-weaving section = 7.0 m
Length of weaving section = 36 m
Proportion of weaving traffic = 40%
What is the practical capacity of the weaving section? What measures would you suggest to enhance the practical capacity? [10]
- (i) What do you understand by hardness in water? Briefly explain the difference in total hardness, carbonate hardness and non-carbonate hardness. [4]
(ii) Calculate total hardness, carbonate hardness and non-carbonate hardness for a sample of water having following characteristics :
Alkalinity = 200 mg/L as $\mathrm{CaCO_3}$
$\mathrm{Ca^{2+}}$ concentration = 160 mg/L as the ion
$\mathrm{Mg^{2+}}$ concentration = 40 mg/L as the ion
pH = 8.1 [6]
- (i) Explain in brief various types of disinfectants and their mechanism, which are used for purification of water at water treatment plants. [4]
(ii) Calculate the chlorine dosage and chlorine demand in mg/L for the chlorine usage of 8 kg/day for treatment of $20000\,\mathrm{m^3}$/day of water when the residual chlorine after 10 min contact is 0.20 mg/L. [6]
- (i) Explain the problems associated with expansive soils while laying the canal lining and remedial measures. [6]
(ii) Discuss the purpose of safety ladders in lined canals along with details. [4]
- The discharge of a tube well is 0.035 cumec and the infiltration capacity of soil is 6 cm/hr. The average depth of flow in the field is 15 cm. Calculate the time required to irrigate the strip of land of 0.06 hectare.
- The initial rainfall intensities of a storm during dry weather flow are 12, 16, 22, 45, 42, 38, 29, 15, 18, 25, 42, 38, 24, 12 and 3 mm/hr at 20 minutes interval. The area of basin is $750\,\mathrm{km^2}$ and $\phi$ index is 18 mm/hr. What will be the runoff volume of the basin, if the initial abstraction is 10 mm?
- (i) Explain well loss and aquifer loss along with figures and equations. [10]
(ii) Explain well development and list the well development methods. [5]
- (i) What do you understand by sludge digestion? [2]
(ii) Briefly explain the distinct stages of sludge digestion and the factors affecting the sludge digestion. [4+4=8]
(iii) Design a circular sludge digestion tank with 6 m depth for the following parameters, when 3.5% of the digester volume is filled on daily basis with the fresh sludge, which is mixed with the digested sludge :
Sludge content per capita per day = 0.68 kg
Moisture of the sludge = 94%
Specific gravity of wet sludge = 1.02
Provide 30% additional capacity for fluctuations. [10]
- (i) Differentiate between stilling basin and cistern, and their application. [7]
(ii) Under what conditions is the hydraulic jump type stilling basin type-1 proposed? Explain with figure. [8]
- (i) Define primary and secondary air pollutants with appropriate examples. [3]
(ii) Name at least five greenhouse gases (GHGs). How do greenhouse gases (GHGs) play role in climate change? [3]
(iii) Illustrate with diagrams the influence of environmental lapse rates on shape and dispersion of plume emitted from stack of a thermal power plant. [9]
- (i) Explain how the water pressure is resisted by the following dams :
1. Gravity dams
2. Earth dams [2]
(ii) How do you arrive the base width of an elementary profile of gravity dam? [8]
(iii) Explain the reasons for cracking of concrete in concrete gravity dams and remedial measures. [10]
- (i) What do you mean by coagulation and flocculation? How do they play role in water purification? Provide a list of most common coagulants used at water treatment plants along with their relative merits or demerits. [5]
(ii) At a water treatment plant, the coagulation-sedimentation unit clarifies 40 million litres of water each day. The quantity of alum required at the plant is 18 mg/L. If the alkalinity of raw water is 5 mg/L as $\mathrm{CaCO_3}$, find out the quantity of alum and quicklime (having 85% of CaO) required on yearly basis at the plant. [10]
- Discuss various maintenance problems posed by irrigation canals during their use and write the remedial measures.
- (i) What are different unit operations and processes used at a typical wastewater treatment plant? [5]
(ii) Draw typical cross-section of a circular trickling filter. Also, briefly describe the merits and demerits of conventional trickling filters. [5]
(iii) Design a high-rate single-stage circular trickling filter to treat wastewater generated by a town having population of 40000 persons. Necessary data are given below to be used for the design purpose :
1. Domestic sewage = 150 lpcd having BOD of 200 mg/L
2. Industrial wastewater = 0.25 million litres/day with BOD of 600 mg/L
3. BOD removal in primary clarifier = 35%
4. Permissible organic loading of the filter = 800 kg/hec-m/day (this does not include recirculated sewage)
5. Recirculation ratio = 1.0
6. Permissible surface loading = 160 million litres/hec/day (this includes recirculated sewage)
Also, find out the efficiency of the filter and BOD of the effluent. [10]
- (i) Differentiate between a weir and a barrage. How do you decide which structure among them is needed at a site of diversion headwork? [5]
(ii) What are the causes of failure of weirs and their remedies? [10]