Mains PYQs
UPSC Mains Civil Engineering paper 1 2016 questions
- For a two-dimensional irrotational flow in the x-y plane, the velocity component in the x-direction is given by $v_x = -x$. Obtain expressions for the stream function $\psi$ and the velocity potential $\phi$, if it is given that $\psi = 0$ for $y = 0$ and $\phi = 0$ at the origin. What type of flow pattern is represented by this ?
- A reinforced concrete rectangular section of size $300\,\mathrm{mm} \times 600\,\mathrm{mm}$ (effective) is reinforced with 4 bars of 20 mm dia on the tension side. Determine the safe uniformly distributed load that the beam can carry over a simply supported effective span of 8 m. The grade of concrete and steel used are M 20 and Fe 415 respectively. For the given environmental exposure, the effective cover to reinforcement is 50 mm.
- For the system shown in Figure 1(c), a small block of mass m and a smooth irregular shaped block of mass M, both free to move, are placed on a smooth horizontal plane. Find the minimum velocity ($v$) to be imparted to the smaller block so that it reaches the highest point of the larger block.
[Figure] Small block m moving with velocity v towards the larger block M of height h.
- Draw the Bending Moment diagram for the CD portion only for the beam shown in Figure 1(d).
[Figure] Beam A to D: A fixed support, AB span 4.0 m with 10 kN/m udl and flexural rigidity 2 EI, free roller at B and C, BD span 2.0 m with 10 kN/m udl and flexural rigidity EI, D fixed support.
- An excavation is made in a soil whose porosity is 30% and the specific gravity of soil solids = 2.6. A 1.5 m thick layer of this soil is subjected to an upward seepage head of 2.0 m. Find out what factor of safety exists against the piping (boiling). If a factor of safety of 2 is needed against the piping, what depth of gravel is required to be placed above the soil layer ? Assume the unit weight of gravel to be the same as that of the soil and negligible loss of head in the gravel layer.
- Check the stability requirements for a cantilever type retaining wall of the dimensions as shown in Figure 2(a) to retain the levelled earth for a height of 4 m above G.L. The safe bearing capacity of soil available at a depth of 1.2 m below the G.L. is $165\,\mathrm{kN/m^2}$. The angle of repose of soil is $30^\circ$ and the coefficient of friction between the soil and concrete is 0.52. The unit weight of the soil is $18\,\mathrm{kN/m^3}$.
[Figure] Dimensions in mm: stem top width 200, retained height 4000 above G.L., 1200 below G.L., base slab 400 thick and 3500 long, toe 1000, heel 2100, stem base width 200 + 200.
- The details of the subsoil conditions at a site are shown in Figure 2(b) together with the details of the soil properties. The ground water level is 1.2 m below the upper surface of the silt. It can be assumed that the gravel has a degree of saturation of 50% and that the silt layer is fully saturated. Plot the total vertical stress, neutral stress (pore pressure) and effective vertical stress over the entire depth of subsoil up to the rock layer. Also, determine the effective vertical stress at a point 1.0 m above the rock layer.
[Figure] Gravel layer 1.8 m thick, $G_s = 2.65$, $e = 0.650$; Silt layer 4.0 m thick, $G_s = 2.58$, $e = 0.76$, W.T. 1.2 m below the top of the silt; Rock below.
- A square foundation has to be constructed on a thick deposit of uniform cohesionless soil with angle of internal friction, $\phi = 34^\circ$. The depth of foundation is 1.2 m. The water table is at a great depth and its effect can be neglected. The allowable design load of the footing with a factor of safety of 3 is 700 kN. Determine the size of the foundation.
Given $\phi = 34^\circ$, $N_c = 52.6$, $N_q = 36.5$ and $N_\gamma = 37.0$ and unit weight of soil, $\gamma = 18\,\mathrm{kN/m^3}$.
- Two moving loads of 100 kN each are moving from left to right on the truss shown in Figure 3(a). Calculate the maximum load in member BG due to the moving loads.
[Figure] Truss with bottom chord A-B-C-D-E, panels of 5 m each, height 5 m, top joints F, G, H above B, C, D; verticals BF, CG, DH; diagonals AF, BG, GD, HE (as drawn); A hinged support, E roller support; two moving loads of 100 kN each, 5 m apart, moving left to right.
- A reinforced concrete beam of rectangular section has a width of 230 mm and an effective depth of 500 mm. The effective covers to tension and compression reinforcements are 40 mm and 30 mm respectively. The beam is reinforced with 3 bars of 20 mm dia in tension and 3 bars of 16 mm dia in compression. Find the limiting moment carrying capacity of the beam. The grade of concrete used is M 20 and steel grade is Fe 415.
- Steady, two-dimensional, fully developed laminar flow of a fluid (mass density $\rho$, dynamic viscosity $\mu$) is taking place on an infinite plate inclined at an angle of $30^\circ$ from the horizontal. The thickness of the fluid layer is h and the top surface has atmospheric pressure. Obtain an expression for the average flow velocity in the direction of flow.
- Water flows through a 1.0 m diameter pipe which has a roughness height, $\varepsilon$, of 0.1 mm. What will be the maximum possible flow rate if the head loss is to be limited to 5 m per km ? Use the following equation for the friction factor :
$$f = \frac{0.25}{\left[\log_{10}\left(\frac{\varepsilon}{3.7\,D} + \frac{5.7}{R_e^{0.9}}\right)\right]^2}$$
Symbols have their usual meanings.
- A submarine is travelling at a large depth in the sea (seawater $\rho = 1030\,\mathrm{kg/m^3}$, $\mu = 1.15 \times 10^{-3}\,\mathrm{N\text{-}s/m^2}$) with a speed of 5 m/s. It is desired to estimate the drag force on the submarine by conducting experiments in a freshwater tank on a scaled model of the submarine. If the length scale is 1 : 25, what should be the speed in the model ? If the drag force on the model is measured as 1000 N, what is the drag force on the submarine ?
- The following results were obtained from a series of consolidated undrained triaxial tests on specimens of saturated clay. Determine the shear strength parameters (both effective stress and total stress) of the soil.
| $\sigma_3$ (kPa) | $(\sigma_1' - \sigma_3')$ at peak (kPa) | u at peak (kPa) |
| --- | --- | --- |
| 100 | 137 | 28 |
| 200 | 210 | 86 |
| 300 | 283 | 147 |
- Sketch the variation of shear stresses for the cross-sections of the beams shown in Figure 5(a) at the point of maximum shear force.
[Figure] Four cross-sections: (i) cross (plus) shaped section, (ii) I-section with the web horizontal between two vertical flanges, (iii) square section with a circular hole, (iv) solid square placed as a diamond.
- A 5 mm diameter nozzle is discharging a vertically upward jet of water with a velocity of 10 m/s at the nozzle. What is the maximum height to which this jet will reach ? If a flat plate weighing 1.5 N is balanced on the jet, what will be its height from the nozzle ?
- A pretensioned prestressed concrete beam, 250 mm wide and 450 mm deep, is prestressed with wires (area $420\,\mathrm{mm^2}$) located at a constant eccentricity of 50 mm and carrying an initial stress of $1\,\mathrm{kN/mm^2}$. The span of the beam is 12 m. Calculate the percentage losses of stress in the wires using the following data :
Modulus of Elasticity of steel $E_s = 200\,\mathrm{kN/m^2}$
Modulus of Elasticity of concrete $E_c = 40\,\mathrm{kN/m^2}$
Coefficient of shrinkage $= 280 \times 10^{-6}$
Coefficient of creep $= 1.6$
- In Figure 5(d), an inclined plane is kept at an angle of $45^\circ$ from horizontal plane at the bottom edge of a smooth wall. A uniform ladder of length $l$ and mass M rests on the inclined plane against the wall such that it is perpendicular to the incline. What is the minimum coefficient of friction necessary so that the ladder does not slip on the incline ?
[Figure] Smooth wall on the left, inclined plane at $45^\circ$ from the horizontal at the wall's bottom, ladder from the wall meeting the incline at a right angle.
- A site with a large areal extent underlain by 10 m thick, horizontal deposit of dry sand over bed rock, initially at a relative density of 50%, was compacted to a final relative density of 80%. The sand was characterised with the maximum and minimum void ratios of 1.0 and 0.5, respectively. Find the surface settlement following compaction.
- Three metal cubes are arranged as shown in Figure 6(a). The central metal cube is subjected to a uniform compressive stress of $1000\,\mathrm{N/mm^2}$. Calculate the volumetric strain of cube 2, if displacement is restrained about the x-axis.
(i) $A_1 = A_2 = A_3 = A$
(ii) $l_1 = l_2 = l_3 = l$
(iii) $E_1 = E_3 = 1.2 \times 10^5\,\mathrm{N/mm^2}$
(iv) $E_2 = 2.1 \times 10^5\,\mathrm{N/mm^2}$
(v) $N_1 = N_3 = 0.20$
(vi) $N_2 = 0.3$
[Figure] Three cubes 1, 2, 3 side by side between two rigid faces, on a rigid base; $\sigma_y = 1000\,\mathrm{N/mm^2}$ acting on the top of cube 2; each cube labelled with $A$, $l$, $E$, $N$; axes x, y, z shown.
- A 500 mm diameter concrete pile is to be driven in a clayey soil. The design capacity of the pile is 500 kN. The soil conditions are shown in Figure 6(b). Determine the length required for the pile for the above design capacity. (Assume $\alpha = 0.75$)
[Figure] Pile of length L in clay with $Q_{design} = 500\,\mathrm{kN}$; clay with $q_u = 115\,\mathrm{kN/m^2}$ and $\gamma = 18.1\,\mathrm{kN/m^3}$.
- Determine the shear reinforcement required for a reinforced concrete beam of T-shaped cross-section with a flange width of 1500 mm, a flange thickness of 100 mm, a web width of 300 mm and an effective depth of 600 mm. The beam is reinforced with 8 bars of 25 mm $\phi$ on the tension side and 4 bars of 16 mm $\phi$ on the compression side. The reinforcements continue uninterrupted into the supports. The beam supports a factored u.d.l. of 80 kN/m over a clear span of 10 m. The grade of concrete is M 20 and steel is Fe 415. The shear strength of concrete is given below :
| Percentage of Steel | Permissible Shear Stress for M 20 in $\mathrm{N/mm^2}$ |
| --- | --- |
| 2.10 | 0.797 |
| 2.12 | 0.799 |
| 2.14 | 0.802 |
| 2.16 | 0.804 |
| 2.18 | 0.806 |
| 2.20 | 0.808 |
- A hydraulic jump is formed in a 2 m wide rectangular channel carrying water at a flow rate of $2\,\mathrm{m^3/s}$. It was found that the velocity head after the jump is only 5% of that before the jump. What are the pre-jump and post-jump depths ?
- Design a simply supported beam with an effective span of 8 m carrying a factored u.d.l. of 10 kN/m. The compression flange is restrained laterally along its entire length and the yield stress of steel is 250 MPa.
The properties of ISMB 300 section are given below :
Area $= 5870\,\mathrm{mm^2}$
D = 300 mm
$b_f$ = 140 mm
$t_f$ = 13.1 mm
$t_w$ = 7.7 mm
$I_{xx} = 8985.7\,\mathrm{cm^4}$
$r_{xx}$ = 124 mm
$r_{yy}$ = 28.6 mm
Unit weight w = 0.461 kN/m
$Z_e = 599 \times 10^3\,\mathrm{mm^3}$
- The coordinates of two points on the virgin compression line are as below :
$\sigma_1' = 400\,\mathrm{kPa}$, $e_1 = 0.8$; $\sigma_2' = 800\,\mathrm{kPa}$, $e_2 = 0.75$
In the field, a 3 m thick normally consolidated layer of this soil subjected to construction load and the average effective vertical stress increased from 250 kPa to 450 kPa. Determine
(i) the compression index and initial void ratio of the clay layer,
(ii) the consolidation settlement of the layer, and
(iii) the load increment to cause 25 mm final consolidation settlement to occur and the corresponding void ratio.
- (i) A long column is initially straight and hinged at both ends. Consider, least moment of inertia I, Young's modulus E, homogeneous material and centre-to-centre distance of hinge support L. Prove that the critical load for the column will be $W_c = \dfrac{\pi^2 EI}{L^2}$. [10]
(ii) A simply supported beam of homogeneous cross-section and material is subjected to axial and transverse loads as shown in Figure 8(a)(ii). Calculate the total stresses at points (1) and (2) of the section C as shown in the figure. [10]
[Figure] Simply supported beam AB of span 10.0 m (C at mid-span, 5.0 m from A), 10 kN/m udl including self-weight of beam, axial compressive loads of 100 kN at each end; section at C is 100 mm wide and 200 mm deep with point 1 at the top left corner and point 2 at the bottom of the section on the axis.
- (i) Flow of air (mass density $1.2\,\mathrm{kg/m^3}$, dynamic viscosity $1.8 \times 10^{-5}\,\mathrm{N\text{-}s/m^2}$) takes place over a rectangular flat plate kept parallel to the flow direction. The flow velocity is 10 m/s and the length of the plate is such that the Reynolds number is critical at the trailing edge (i.e., the boundary layer is laminar throughout). The width of the plate is half of its length. The plate is then rotated by $90^\circ$ in its plane so that the flow is now taking place along the shorter side. Find the ratio of the drag forces under these two flow situations. [10]
(ii) Why are the characteristic curves needed for a turbine ? What are the various types of characteristic curves ? Show a typical constant head characteristic curve between unit speed and unit power for a Pelton wheel turbine. [10]
- A circular copper bar is carrying a tensile load of 200 kN as shown in Figure 8(c). Calculate the displacement of point B of the copper bar.
Cross-sectional area of the copper bar $= 5000\,\mathrm{mm^2}$
Cross-sectional area of each of the steel bars $= 5000\,\mathrm{mm^2}$
Length of the copper bar = 3.0 m
Length of each of the steel bars = 1.0 m
$E_{steel}$ = 210 GPa, $E_{copper}$ = 120 GPa
[Figure] Rigid plate at A with two steel bars (1.0 m long) and a central copper bar (3.0 m long) hanging from it through a fixed support; 200 kN load at the lower end B of the copper bar.