Mains PYQs
UPSC IFoS Mains Chemical Engineering paper 2 2020 questions
- Define 'wet bulb' and 'dry bulb' temperatures. Dry mixture of HCl gas and air is passed over a heated catalyst, which promotes oxidation of acid. Air is used in 20% excess of that theoretically required. Calculate the weight of air supplied per kg of acid.
- A sample of limestone has $\mathrm{CaCO_3}$ (84% w/w), $\mathrm{MgCO_3}$ (12% w/w) and inert (4% w/w). Calculate the weight of CaO, obtained by 250 kg of sample limestone.
- Explain the need of equations of state for real gases, and discuss the limiting conditions that should be satisfied by an equation of state.
- For a reaction $A \rightarrow 4R$, occurring in a variable volume batch reactor, derive the following expression :
$$C_A = C_{A_0}\left(\frac{1 - X_A}{1 + \varepsilon_A X_A}\right)$$
where $C_{A_0}$ and $C_A$ are concentrations at $t = 0$ and time $t$; $\varepsilon_A$ is fractional change in volume; $X_A$ is the conversion.
- What is degree of dissociation? A vessel has one mole $\mathrm{N_2O_4}$ at $27\,^\circ\mathrm{C}$ and one atmospheric pressure. The dissociation reaction takes place as
$$\mathrm{N_2O_4 \rightleftharpoons 2NO_2}\;(g)$$
Calculate the degree of dissociation, if $K_p$ for the above reaction is 0.114.
- A 500 lit/s of gaseous mixture of the following composition (v/v) is at $27\,^\circ\mathrm{C}$ and 2000 mm Hg gauge :
$\mathrm{CH_4}$ = 20%, $\mathrm{C_2H_6}$ = 30%, $\mathrm{H_2}$ = 50%
Calculate-
(i) the mole fraction of each component;
(ii) the molar density of the mixture.
- Discuss the term 'enthalpy of gaseous component'. $\mathrm{C_8H_{18}}$ is burnt with 20% excess air. Calculate the air/fuel ratio by weight. The average molecular weight of air is 28.84.
- Define the term 'adiabatic flame temperature'. A biogas sample has the following molar composition :
$\mathrm{CH_4}$ = 64%
$\mathrm{CO_2}$ = 36%
Calculate the average molecular weight of this sample.
- In a steam power plant, superheated steam at 673 K and 2 MPa enters the turbine and it is expanded to the condenser pressure of 7.5 kPa. Assuming an isentropic pump efficiency of 85% and an isentropic turbine efficiency of 90%, calculate the following :
(i) The ideal Rankine cycle efficiency for the given conditions
(ii) The thermal efficiency of the plant
Additional data :
The specific volume of saturated liquid at 7.5 kPa is $1.008 \times 10^{-3}\,\mathrm{m^3/kg}$.
| | Temperature (K) | Pressure (kPa) | Enthalpy (kJ/kg) | Entropy (kJ/kg-K) |
|---|---|---|---|---|
| Saturated liquid | 313.44 | 7.5 | 168.79 | 0.5764 |
| Saturated vapour | 313.44 | 7.5 | 2574.80 | 8.2515 |
| Superheated steam | 673 | 2000 | 3247.60 | 7.1271 |
- Conventionally a partial property $\overline{M}_i$ of species $i$ in solution is defined as $\overline{M}_i \equiv \left[\frac{\partial (nM)}{\partial n_i}\right]_{P,T,n_j}$. Correspondingly, a constant-$T$, $V$ partial property $\hat{M}_i$ may be defined as $\hat{M}_i \equiv \left[\frac{\partial (nM)}{\partial n_i}\right]_{T,V,n_j}$. Show that $\overline{M}_i$ and $\hat{M}_i$ are related by the equation $\hat{M}_i = \overline{M}_i + (V - \overline{V}_i)\left(\frac{\partial M}{\partial V}\right)_{T,x}$.
- Consider a reaction being carried out in gas phase :
$$aA + bB \rightarrow cC + dD$$
where $a$, $b$, $c$ and $d$ are the stoichiometric coefficients of the chemical species $A$, $B$, $C$ and $D$, respectively. Given that the reactants and the products are at their standard state. Develop a series of speculative steps for carrying out this reaction, and show that the free energy changes calculated for these series of steps add up to conform the relationship $\Delta G^\circ = -RT \ln K$.
- What do you understand by 'plug flow'? Derive the design equation of a plug flow reactor (PFR) with the help of suitable assumptions.
- Define the term 'effectiveness factor' in heterogeneous catalysis. Also calculate the activation energy and frequency factor from the following data :
| $k$, $\mathrm{sec^{-1}}$ | $T$, K |
|---|---|
| $4.4 \times 10^{-4}$ | 312 |
| $7.2 \times 10^{-3}$ | 332 |
- What do you understand by 'cascading of CSTRs'? $A + B \rightarrow C$ takes place in a two-stage CSTR, having volume of 100 $\mathrm{m^3}$ and 25 $\mathrm{m^3}$, respectively. The volumetric feed rate is 20 lit/min. $C_A = C_B = 1.5$ g mol/lit and overall rate constant is 0.010 lit/g mol min. Calculate the overall conversion.
- Differentiate between soap and detergent. Discuss the reactions involved in the detergent manufacturing process from coconut oil.
- Describe coking of coal process. Also account for the major engineering problems associated with the process.
- A cyclone has an inlet width of 10 cm and four effective turns ($N$ = 4). The gas temperature is 350 K and the inlet velocity is 10 m/s. The average particle diameter is 8 $\mu$m and the average density is 1.5 $\mathrm{g/cm^3}$. What is the collection efficiency? The viscosity of air at 350 K is 0.0748 kg/m-h. We can assume that $\rho_{air}$ is negligible compared to $\rho_{particles}$.
[Figure]
Cyclone efficiency: collection efficiency (percent, 10 to 100) against particle-size ratio $d/d_c$ (0.3 to 10).
- A clean filter is found to weigh 10.00 g. After 24 hr in a high-volume sampler, the filter plus dust weighs 10.10 g. The air flow at start and end of test was 60 $\mathrm{ft^3/min}$ and 40 $\mathrm{ft^3/min}$, respectively. What is the concentration of particulate matter?
- State and explain different types of depreciation.
- Discuss the importance of cracking process in petroleum refining. Describe in detail and compare hydrocracking and catalytic cracking processes with appropriate diagrams.
- Discuss and differentiate the structural, physical and mechanical properties of LDPE, HDPE and LLDPE. Also mention the general applications of various types of polyethylenes.
- What are antibiotics? Describe the production of antibiotics in industry by fermentation.
- Discuss the classification of air pollutants and water pollutants with proper examples.
- Discuss the Environment Protection Acts for air, water and forest conservation.
- Describe solid waste management. Also discuss the 'integrated solid waste management system' with suitable diagram and table.
- Write a note on 'estimation of purchase equipment cost'. Explain CPM and PERT with proper examples.
- Write a note on plant layout. During the design of a new project, make a decision regarding which type of pump should be used for a corrosive service. The options are as follows :
| | Capital cost | Operating cost (per year) | Equipment life (years) |
|---|---|---|---|
| Carbon steel pump | $ 8,000 | $ 1,800 | 4 |
| Stainless steel pump | $ 16,000 | $ 1,600 | 7 |
- Explain non-discounted profitability criterion with the help of suitable example and diagrammatic illustration.