Mains PYQs
UPSC IFoS Mains Chemical Engineering paper 1 2018 questions
- State Fick's first law of diffusion. Prove that $D_{AB} = D_{BA}$.
- Calculate the critical speed of a ball mill, 1200 mm in diameter, charged with 75 mm balls.
- Air at 300 K and 1.0 atm pressure flows over a flat plate at a speed of 3.0 m/sec. Find out whether the flow would be laminar or turbulent at a distance of 40 cm from the leading edge of the plate. Consider momentum diffusivity of air as = $1.572 \times 10^{-5}\,\mathrm{m^2/s}$.
- Give the selection criteria of choosing the solvent in gas absorption column.
- A solution of organic colloids; 10,000 kg/hr is to be concentrated from 15% to 50% solids in a vertical tube evaporator by supplying heat of 4.624 MW. The saturated steam is available at 0.8 atm absolute pressure, latent heat = 2272.62 J/kg. Calculate the economy for the evaporator.
- Draw and explain the characteristic curves for centrifugal pump.
- The x-directed momentum transfer equation for constant density and viscosity is given by
$$\rho\left(\frac{\partial v_x}{\partial t} + v_x\frac{\partial v_x}{\partial x} + v_y\frac{\partial v_x}{\partial y} + v_z\frac{\partial v_x}{\partial z}\right) = -\frac{\partial p}{\partial x} + \mu\left[\frac{\partial^2 v_x}{\partial x^2} + \frac{\partial^2 v_x}{\partial y^2} + \frac{\partial^2 v_x}{\partial z^2}\right] + \rho g_x$$
Write the assumptions of creeping flow and inviscid flow. Also reduce the above expression for both types of flows.
- For fluid allocation in a shell and tube heat exchanger, discuss the general design criteria considering corrosion, fouling, fluid temperature and operating pressure.
- Differentiate between the following :
(i) Dropwise condensation and Film condensation
(ii) Space and Surface resistance
(iii) Forced and Free convection
(iv) Black body and Grey body
(v) Conduction and Convection
- A liquid mixture of benzene and toluene containing 50 mole percent benzene is to be separated in a distillation column to achieve 98 mole percent benzene in distillate and 2 mole percent benzene in residue. The feed is a saturated liquid. If the reflux ratio of 4.0 is to be used, find the number of theoretical plates needed for a feed rate of 100 kmoles/hr by McCabe-Thiele method. Use relative volatility of benzene-toluene = 2.16. Also, calculate the production rates.
- Explain the batch sedimentation process showing different zones formed at various stages of settling.
- Explain the working of rotary vacuum drum filter with the help of neat sketch.
- Suppose a 3 inch schedule 80 pipe (inside diameter = 73.66 mm; outside diameter = 88.9 mm) having thermal conductivity of $43\,\mathrm{W/m\,^\circ C}$ is covered with 25.4 mm of an insulation having thermal conductivity of $0.06\,\mathrm{W/m\,^\circ C}$. The outside of the insulation is exposed to an environment having heat transfer coefficient of $10\,\mathrm{W/m^2\,^\circ C}$ and temperature is 20°C. The temperature of the inside surface of the pipe is 250°C. Calculate the overall thermal resistance and heat loss for unit length of the pipe with insulation.
- Oxalic acid is to be crystallized from a saturated aqueous solution initially at 80°C. To what temperature does the solution have to be cooled to crystallize 95% of the oxalic acid as the dihydrate ?
Solubility data vs Temperature of oxalic acid
| Temp °C | 0 | 10 | 20 | 40 | 60 | 80 |
|---|---|---|---|---|---|---|
| Solubility c gms/100 gmol $\mathrm{H_2O}$ | 3.5 | 6 | 9.5 | 21.6 | 44.3 | 84.4 |
- Explain briefly the following terms :
(i) Relative humidity
(ii) Adiabatic saturation temperature
(iii) Wet bulb temperature
(iv) Equilibrium moisture content
(v) HETP
- A shell and tube heat exchanger with one shell pass and two tube passes is used to heat 5 kg/s of water from 30°C to 80°C. The water flows in the tubes and condensing steam at 1 atm is used in the shell side. Calculate the area of the heat exchanger, if overall heat transfer coefficient is $900\,\mathrm{W/m^2\,^\circ C}$. Suppose, this same heat exchanger is used with entering water at 30°C, but with a water flow rate of 1.3 kg/s. What would be the exit water temperature under these conditions, if overall heat transfer coefficient is $700\,\mathrm{W/m^2\,^\circ C}$ ? The specific heat of water may be considered as $4179\,\mathrm{J/kg\,^\circ C}$. The relation of effectiveness ($\varepsilon$) and number of transfer units (NTU) may be expressed as $\varepsilon = 1 - \exp[-\mathrm{NTU}]$.
- Water at 20°C is being pumped from a tank to an elevated tank at the rate of 5 litre/s through a 4 inch schedule 40 pipe (Inside Diameter = 0.1023 m) as shown in the figure below. Calculate the power required for the pump considering pump efficiency as 65%.
Given Data :
density of water = $998.2\,\mathrm{kg/m^3}$
viscosity of water = $1.005 \times 10^{-3}$ Pa-s
loss coefficient for elbow = 0.75
friction factor (f) = $\dfrac{16}{N_{Re}}$ (Laminar flow)
$f = 0.079\,N_{Re}^{-0.25}$ ($4000 < N_{Re} < 10^5$)
Neglect contraction and expansion losses.
[Figure] Lower tank with pump; 5 m of pipe then 50 m run; elevated tank 15 m above the lower tank's liquid level; 100 m horizontal distance marked.
- List the important characteristics to be considered while selecting a material of construction.
- Define the following :
(i) Flux
(ii) Permeability
(iii) Trans-membrane pressure
(iv) Molecular weight cut-off
- Estimate the thickness of the cylindrical vessel having 1.5 m diameter. The vessel is to operate at a pressure of 15 bar absolute and temperature of 300°C.
Given – MOC : Steel (Design stress = 85 $\mathrm{N/mm^2}$); A corrosion allowance of 3 mm and Joint efficiency (J) = 1.0.
- What are Horton spheres ? Give its applications.
- Define controller's gain, $K_c$ and discuss the effect of value of $K_c$ on the offset.
- Find the transfer function Y(s)/X(s) of the system shown in the figure.
[Figure] Block diagram: input X into a summing junction (minus sign), then a second summing junction (plus sign), then block $\frac{1}{\tau_1 s + 1}$ in series with block $\frac{0.5}{\frac{\tau_1 s}{2} + 1}$ to output Y; the output of the second block is fed back to the second junction and the output Y is fed back to the first junction.
- List the devices used for high temperature measurement in industry giving their applications.
- A step change of magnitude 40 is introduced into a system having transfer function $\dfrac{Y(s)}{X(s)} = \dfrac{10}{s^2 + 1.6s + 4}$.
Determine :
(i) Overshoot
(ii) Maximum value of y(t)
(iii) Ultimate value of y(t)
- Discuss the algorithm for the design of a skirt support for a tall vertical vessel.
- Find the value of $K_c$ for a stable system having the characteristic equation
$$s^3 + 6s^2 + 12s + 6(1 + K_c) = 0$$
using Routh Array test.
- Discuss the different membrane modules used for reverse osmosis.
- Construct the Bode plot for the system having $G(s) = \dfrac{1}{(s+1)(s+5)}$.
Semi log graph paper
[Figure] Semi-log graph paper grid. Log log graph paper grid on the next page.
- What are the advantages of supercritical fluid separation technique ? List four applications for the same.
- List the different types of closures used for vessels under internal pressure. Draw neat sketches of the same. On what factors does the choice of closure depend ?
- Describe the working of Bourdon tube pressure gauge with the help of a neat diagram.
- Explain the principles of ion-exchange method and its application to water softening process.
- Answer the following in brief :
(i) What are the various losses encountered while storing volatile liquids ?
(ii) What are wind girders ? Why are they provided ?
(iii) What is reinforcement ? Why is it provided ?