Mains PYQs
UPSC IFoS Mains Chemical Engineering paper 2 2016 questions
- Explain the following terms with suitable illustrations for an operation involving reaction with recycle :
(i) Overall conversion
(ii) Single-pass conversion
- Define the following terms for combustion reaction :
(i) Theoretical oxygen demand
(ii) Percentage of excess air
- Define degrees of freedom of each of the following equilibrium systems using Gibbs' phase rule :
(i) A vapour-liquid mixture of four hydrocarbons
(ii) $\mathrm{NaCl}$ crystals suspended in an aqueous $\mathrm{NaCl}$ solution
- State Raoult's law and indicate its applications in vapour-liquid equilibrium calculations.
- Define half-life time $[t_{1/2}]$ of a reaction and derive the half-life time expression for first-order reaction.
- What are the factors that influence the selection of a catalyst for a catalytic reaction?
- What is an equation of state? What is the ideal gas equation? At what conditions does the ideal gas equation provide the most accurate estimates?
- What are the factors that influence the choice of good refrigerant for a refrigeration unit?
- Methane burns in a reactor according to the following stoichiometry :
$$\mathrm{CH_4 + 2O_2 \rightarrow CO_2 + 2H_2O}$$
$$\mathrm{CH_4 + 1.5O_2 \rightarrow CO + 2H_2O}$$
One hundred mol/h of methane is fed to a reactor.
(i) What is the theoretical $\mathrm{O_2}$ flow rate if the complete combustion occurs in the reactor?
(ii) What is the theoretical $\mathrm{O_2}$ flow rate assuming that only 70% methane reacts?
(iii) What is the theoretical flow rate of air?
(iv) If the actual flow rate of air is such that $300\,\mathrm{mol}\ \mathrm{O_2/h}$ enters the reactor, what is the percent excess air?
- Explain Hess' law of heat summation with its significance. Suppose heats of reaction at $25\,^\circ\mathrm{C}$ are measured experimentally for the following set of reactions :
$$2A + B \rightarrow 2C \quad : \Delta\hat{H}^{\circ}_{r_1} = -1000\,\mathrm{kJ/mol}$$
$$A + D \rightarrow C + 3E \quad : \Delta\hat{H}^{\circ}_{r_2} = -2000\,\mathrm{kJ/mol}$$
Using Hess' law, calculate the heats of reaction for the following reaction at $25\,^\circ\mathrm{C}$ :
$$B + 6E \rightarrow 2D$$
- An ice plant working on a reversed Carnot cycle heat pump produces 20 tonnes of ice per day. The ice is maintained at $0\,^\circ\mathrm{C}$. The heat is rejected to the atmosphere at $27\,^\circ\mathrm{C}$. The heat pump which is used to run the ice plant is coupled to a Carnot engine which absorbs heat from a source which is maintained at $227\,^\circ\mathrm{C}$ by burning fuel of $45000\,\mathrm{kJ/kg}$ calorific value and rejects the heat to the atmosphere. Determine the consumption of fuel per hour and the power developed by the engine. Take enthalpy of fusion of ice $= 334.5\,\mathrm{kJ/kg}$.
- An equimolar liquid mixture of Benzene (B) and Toluene (T) is in equilibrium with its vapour. What is the system pressure and the composition of vapour?
Hint : The Antoine equation may be used to estimate the vapour pressure of Benzene (B) and Toluene (T) :
$$\log_{10} P_B^* = 6.906 - \frac{1211}{T + 220.8}$$
$$\log_{10} P_T^* = 6.9533 - \frac{1343.9}{T + 219.38}$$
where $P_B^*$ and $P_T^*$ are vapour pressures of Benzene and Toluene in mm Hg and $T$ is the temperature in $^\circ\mathrm{C}$.
- In a batch reactor, decomposition reaction in liquid phase takes place with a first-order kinetics. 50% of the reactant is converted to product in 5 minutes experimental run.
(i) What is the value of rate constant?
(ii) How much longer would it take to reach 75% conversion?
- Consider a series reaction with the following stoichiometry which takes place in an ideal plug flow reactor :
$$A \xrightarrow{k_1 = 0.1\,\mathrm{min^{-1}}} R \xrightarrow{k_2 = 0.1\,\mathrm{min^{-1}}} S$$
The feed is introduced into the reactor at 1000 litres/h and the feed contains only the reactant with the concentration of 1 g mole/litre.
(i) What is the maximum concentration of $R$ in the product stream?
(ii) What is the volume of the reactor?
- Discuss in detail about setting and hardening of cement.
- Describe the various methods for extraction of vegetable oils.
- Differentiate between hazards, risk and safety. Give the classification of hazards.
- What are the by-products of sugar industry? Mention their utilizations.
- What are the preventive and protective measures to prevent fire in chemical industry?
- Discuss in detail about various legislations for safety control presently applicable in chemical process plants.
- Explain the different methods for determining the depreciation of process equipments and compare them.
- Explain the various factors to be considered while deciding the plant location.
- What are the characteristics of alkaline pulp? Explain in detail about the kraft pulping process with a neat sketch.
- Differentiate between soaps and detergents. Explain the continuous process for the production of fatty acids and soap in detail.
- Compare aerobic and anaerobic methods for composting of municipal solid wastes. Discuss in detail about various treatments adopted for the treatment of industrial wastewater with neat sketch.
- Discuss the safety aspects in the design of chemical plants and suggest a suitable control scheme for safe operation of chemical reactor.
- The following equation shows the effect of variables $x$ and $y$ on the total cost for a particular operation :
$$C_T = 2.33x + \frac{11900}{xy} + 1.86y + 10$$
Determine the values of $x$ and $y$ which will give the least total cost.
- A chemical plant requires ₹50,00,000 of fixed capital investment. If annual profits and annual depreciation costs are ₹15,00,000 and ₹7,50,000 respectively, find the payback period on total investment.
- Explain the break-even chart for the production schedule with neat sketch and explain its significance for optimum analysis.